[PATCH v4 12/12] ARM: mvebu: Relocate Armada XP PCIe device tree nodes
Ezequiel Garcia
ezequiel.garcia at free-electrons.com
Wed Jun 19 16:07:26 EDT 2013
Now that mbus has been added to the device tree, it's possible to
move the PCIe nodes out of internal registers, placing it directly
below the mbus. This is a more accurate representation of the
hardware.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia at free-electrons.com>
---
arch/arm/boot/dts/armada-xp-db.dts | 67 ++--
arch/arm/boot/dts/armada-xp-gp.dts | 43 +--
arch/arm/boot/dts/armada-xp-mv78230.dtsi | 209 ++++++-------
arch/arm/boot/dts/armada-xp-mv78260.dtsi | 245 +++++++--------
arch/arm/boot/dts/armada-xp-mv78460.dtsi | 377 ++++++++++++-----------
arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts | 19 +-
6 files changed, 483 insertions(+), 477 deletions(-)
diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts
index d157387..ef0d2c5 100644
--- a/arch/arm/boot/dts/armada-xp-db.dts
+++ b/arch/arm/boot/dts/armada-xp-db.dts
@@ -31,8 +31,42 @@
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+ MBUS_ID(0xf0, 0x02) 0xe0000000 0 0xe0000000 0x8100000
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
+ pcie-controller {
+ status = "okay";
+
+ /*
+ * All 6 slots are physically present as
+ * standard PCIe slots on the board.
+ */
+ pcie at 1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ pcie at 2,0 {
+ /* Port 0, Lane 1 */
+ status = "okay";
+ };
+ pcie at 3,0 {
+ /* Port 0, Lane 2 */
+ status = "okay";
+ };
+ pcie at 4,0 {
+ /* Port 0, Lane 3 */
+ status = "okay";
+ };
+ pcie at 9,0 {
+ /* Port 2, Lane 0 */
+ status = "okay";
+ };
+ pcie at 10,0 {
+ /* Port 3, Lane 0 */
+ status = "okay";
+ };
+ };
+
internal-regs {
serial at 12000 {
clock-frequency = <250000000>;
@@ -125,39 +159,6 @@
spi-max-frequency = <20000000>;
};
};
-
- pcie-controller {
- status = "okay";
-
- /*
- * All 6 slots are physically present as
- * standard PCIe slots on the board.
- */
- pcie at 1,0 {
- /* Port 0, Lane 0 */
- status = "okay";
- };
- pcie at 2,0 {
- /* Port 0, Lane 1 */
- status = "okay";
- };
- pcie at 3,0 {
- /* Port 0, Lane 2 */
- status = "okay";
- };
- pcie at 4,0 {
- /* Port 0, Lane 3 */
- status = "okay";
- };
- pcie at 9,0 {
- /* Port 2, Lane 0 */
- status = "okay";
- };
- pcie at 10,0 {
- /* Port 3, Lane 0 */
- status = "okay";
- };
- };
};
};
};
diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts
index 30bf645..c328538 100644
--- a/arch/arm/boot/dts/armada-xp-gp.dts
+++ b/arch/arm/boot/dts/armada-xp-gp.dts
@@ -40,6 +40,7 @@
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+ MBUS_ID(0xf0, 0x02) 0xe0000000 0 0xe0000000 0x8100000
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>;
@@ -71,6 +72,27 @@
};
};
+ pcie-controller {
+ status = "okay";
+
+ /*
+ * The 3 slots are physically present as
+ * standard PCIe slots on the board.
+ */
+ pcie at 1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ pcie at 9,0 {
+ /* Port 2, Lane 0 */
+ status = "okay";
+ };
+ pcie at 10,0 {
+ /* Port 3, Lane 0 */
+ status = "okay";
+ };
+ };
+
internal-regs {
serial at 12000 {
clock-frequency = <250000000>;
@@ -144,27 +166,6 @@
spi-max-frequency = <108000000>;
};
};
-
- pcie-controller {
- status = "okay";
-
- /*
- * The 3 slots are physically present as
- * standard PCIe slots on the board.
- */
- pcie at 1,0 {
- /* Port 0, Lane 0 */
- status = "okay";
- };
- pcie at 9,0 {
- /* Port 2, Lane 0 */
- status = "okay";
- };
- pcie at 10,0 {
- /* Port 3, Lane 0 */
- status = "okay";
- };
- };
};
};
};
diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
index f8eaa38..448b826 100644
--- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
@@ -44,6 +44,111 @@
};
soc {
+ /*
+ * MV78230 has 2 PCIe units Gen2.0: One unit can be
+ * configured as x4 or quad x1 lanes. One unit is
+ * x4/x1.
+ */
+ pcie-controller {
+ compatible = "marvell,armada-xp-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000 /* Port 2.0 registers */
+ 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 /* Port 0.1 registers */
+ 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */
+ 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */
+ 0x82000000 0 0xe0000000 MBUS_ID(0xf0, 0x02) 0xe0000000 0 0x08000000 /* non-prefetchable memory */
+ 0x81000000 0 0 MBUS_ID(0xf0, 0x02) 0xe8000000 0 0x00100000>; /* downstream I/O */
+
+ pcie at 1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+
+ pcie at 2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 59>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 6>;
+ status = "disabled";
+ };
+
+ pcie at 3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+ reg = <0x1800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 60>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 7>;
+ status = "disabled";
+ };
+
+ pcie at 4,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+ reg = <0x2000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 61>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 8>;
+ status = "disabled";
+ };
+
+ pcie at 9,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+ reg = <0x4800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 99>;
+ marvell,pcie-port = <2>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 26>;
+ status = "disabled";
+ };
+ };
+
internal-regs {
pinctrl {
compatible = "marvell,mv78230-pinctrl";
@@ -77,110 +182,6 @@
#interrupts-cells = <2>;
interrupts = <87>, <88>, <89>;
};
-
- /*
- * MV78230 has 2 PCIe units Gen2.0: One unit can be
- * configured as x4 or quad x1 lanes. One unit is
- * x4/x1.
- */
- pcie-controller {
- compatible = "marvell,armada-xp-pcie";
- status = "disabled";
- device_type = "pci";
-
-#address-cells = <3>;
-#size-cells = <2>;
-
- bus-range = <0x00 0xff>;
-
- ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
- 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */
- 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */
- 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */
- 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */
- 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
- 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
-
- pcie at 1,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
- reg = <0x0800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 58>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 5>;
- status = "disabled";
- };
-
- pcie at 2,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
- reg = <0x1000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 59>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <1>;
- clocks = <&gateclk 6>;
- status = "disabled";
- };
-
- pcie at 3,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
- reg = <0x1800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 60>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <2>;
- clocks = <&gateclk 7>;
- status = "disabled";
- };
-
- pcie at 4,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
- reg = <0x2000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 61>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <3>;
- clocks = <&gateclk 8>;
- status = "disabled";
- };
-
- pcie at 9,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
- reg = <0x4800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 99>;
- marvell,pcie-port = <2>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 26>;
- status = "disabled";
- };
- };
};
};
};
diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
index c80c60e..f0d29dd 100644
--- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
@@ -45,6 +45,129 @@
};
soc {
+ /*
+ * MV78260 has 3 PCIe units Gen2.0: Two units can be
+ * configured as x4 or quad x1 lanes. One unit is
+ * x4/x1.
+ */
+ pcie-controller {
+ compatible = "marvell,armada-xp-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000 /* Port 2.0 registers */
+ 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 /* Port 0.1 registers */
+ 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */
+ 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */
+ 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */
+ 0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000 /* Port 3.0 registers */
+ 0x82000000 0 0xe0000000 MBUS_ID(0xf0, 0x02) 0xe0000000 0 0x08000000 /* non-prefetchable memory */
+ 0x81000000 0 0 MBUS_ID(0xf0, 0x02) 0xe8000000 0 0x00100000>; /* downstream I/O */
+
+ pcie at 1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+
+ pcie at 2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 59>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 6>;
+ status = "disabled";
+ };
+
+ pcie at 3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+ reg = <0x1800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 60>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 7>;
+ status = "disabled";
+ };
+
+ pcie at 4,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+ reg = <0x2000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 61>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 8>;
+ status = "disabled";
+ };
+
+ pcie at 9,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+ reg = <0x4800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 99>;
+ marvell,pcie-port = <2>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 26>;
+ status = "disabled";
+ };
+
+ pcie at 10,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x82000 0 0x2000>;
+ reg = <0x5000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 103>;
+ marvell,pcie-port = <3>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 27>;
+ status = "disabled";
+ };
+ };
+
internal-regs {
pinctrl {
compatible = "marvell,mv78260-pinctrl";
@@ -97,128 +220,6 @@
clocks = <&gateclk 1>;
status = "disabled";
};
-
- /*
- * MV78260 has 3 PCIe units Gen2.0: Two units can be
- * configured as x4 or quad x1 lanes. One unit is
- * x4/x1.
- */
- pcie-controller {
- compatible = "marvell,armada-xp-pcie";
- status = "disabled";
- device_type = "pci";
-
- #address-cells = <3>;
- #size-cells = <2>;
-
- bus-range = <0x00 0xff>;
-
- ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
- 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */
- 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */
- 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */
- 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */
- 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */
- 0x82000000 0 0x82000 0x82000 0 0x00002000 /* Port 3.0 registers */
- 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
- 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
-
- pcie at 1,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
- reg = <0x0800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 58>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 5>;
- status = "disabled";
- };
-
- pcie at 2,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
- reg = <0x1000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 59>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <1>;
- clocks = <&gateclk 6>;
- status = "disabled";
- };
-
- pcie at 3,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
- reg = <0x1800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 60>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <2>;
- clocks = <&gateclk 7>;
- status = "disabled";
- };
-
- pcie at 4,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
- reg = <0x2000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 61>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <3>;
- clocks = <&gateclk 8>;
- status = "disabled";
- };
-
- pcie at 9,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
- reg = <0x4800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 99>;
- marvell,pcie-port = <2>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 26>;
- status = "disabled";
- };
-
- pcie at 10,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x82000 0 0x2000>;
- reg = <0x5000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 103>;
- marvell,pcie-port = <3>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 27>;
- status = "disabled";
- };
- };
};
};
};
diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
index 3874548..ac10503 100644
--- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
@@ -60,6 +60,195 @@
};
soc {
+ /*
+ * MV78460 has 4 PCIe units Gen2.0: Two units can be
+ * configured as x4 or quad x1 lanes. Two units are
+ * x4/x1.
+ */
+ pcie-controller {
+ compatible = "marvell,armada-xp-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000 /* Port 2.0 registers */
+ 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 /* Port 0.1 registers */
+ 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */
+ 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */
+ 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */
+ 0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000 /* Port 3.0 registers */
+ 0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000 /* Port 1.1 registers */
+ 0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000 /* Port 1.2 registers */
+ 0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000 /* Port 1.3 registers */
+ 0x82000000 0 0xe0000000 MBUS_ID(0xf0, 0x02) 0xe0000000 0 0x08000000 /* non-prefetchable memory */
+ 0x81000000 0 0 MBUS_ID(0xf0, 0x02) 0xe8000000 0 0x00100000>; /* downstream I/O */
+
+ pcie at 1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+
+ pcie at 2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 59>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 6>;
+ status = "disabled";
+ };
+
+ pcie at 3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
+ reg = <0x1800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 60>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 7>;
+ status = "disabled";
+ };
+
+ pcie at 4,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
+ reg = <0x2000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 61>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 8>;
+ status = "disabled";
+ };
+
+ pcie at 5,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+ reg = <0x2800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 62>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 9>;
+ status = "disabled";
+ };
+
+ pcie at 6,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
+ reg = <0x3000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 63>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 10>;
+ status = "disabled";
+ };
+
+ pcie at 7,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
+ reg = <0x3800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 64>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 11>;
+ status = "disabled";
+ };
+
+ pcie at 8,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
+ reg = <0x4000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 65>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 12>;
+ status = "disabled";
+ };
+ pcie at 9,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
+ reg = <0x4800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 99>;
+ marvell,pcie-port = <2>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 26>;
+ status = "disabled";
+ };
+
+ pcie at 10,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
+ reg = <0x5000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 103>;
+ marvell,pcie-port = <3>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 27>;
+ status = "disabled";
+ };
+ };
+
internal-regs {
pinctrl {
compatible = "marvell,mv78460-pinctrl";
@@ -112,194 +301,6 @@
clocks = <&gateclk 1>;
status = "disabled";
};
-
- /*
- * MV78460 has 4 PCIe units Gen2.0: Two units can be
- * configured as x4 or quad x1 lanes. Two units are
- * x4/x1.
- */
- pcie-controller {
- compatible = "marvell,armada-xp-pcie";
- status = "disabled";
- device_type = "pci";
-
- #address-cells = <3>;
- #size-cells = <2>;
-
- bus-range = <0x00 0xff>;
-
- ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
- 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */
- 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */
- 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */
- 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */
- 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */
- 0x82000000 0 0x82000 0x82000 0 0x00002000 /* Port 3.0 registers */
- 0x82000000 0 0x84000 0x84000 0 0x00002000 /* Port 1.1 registers */
- 0x82000000 0 0x88000 0x88000 0 0x00002000 /* Port 1.2 registers */
- 0x82000000 0 0x8c000 0x8c000 0 0x00002000 /* Port 1.3 registers */
- 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
- 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
-
- pcie at 1,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
- reg = <0x0800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 58>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 5>;
- status = "disabled";
- };
-
- pcie at 2,0 {
- device_type = "pci";
- assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
- reg = <0x1000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 59>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <1>;
- clocks = <&gateclk 6>;
- status = "disabled";
- };
-
- pcie at 3,0 {
- device_type = "pci";
- assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
- reg = <0x1800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 60>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <2>;
- clocks = <&gateclk 7>;
- status = "disabled";
- };
-
- pcie at 4,0 {
- device_type = "pci";
- assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
- reg = <0x2000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 61>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <3>;
- clocks = <&gateclk 8>;
- status = "disabled";
- };
-
- pcie at 5,0 {
- device_type = "pci";
- assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
- reg = <0x2800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 62>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 9>;
- status = "disabled";
- };
-
- pcie at 6,0 {
- device_type = "pci";
- assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
- reg = <0x3000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 63>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <1>;
- clocks = <&gateclk 10>;
- status = "disabled";
- };
-
- pcie at 7,0 {
- device_type = "pci";
- assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
- reg = <0x3800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 64>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <2>;
- clocks = <&gateclk 11>;
- status = "disabled";
- };
-
- pcie at 8,0 {
- device_type = "pci";
- assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
- reg = <0x4000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 65>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <3>;
- clocks = <&gateclk 12>;
- status = "disabled";
- };
- pcie at 9,0 {
- device_type = "pci";
- assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
- reg = <0x4800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 99>;
- marvell,pcie-port = <2>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 26>;
- status = "disabled";
- };
-
- pcie at 10,0 {
- device_type = "pci";
- assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
- reg = <0x5000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 103>;
- marvell,pcie-port = <3>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 27>;
- status = "disabled";
- };
- };
};
};
};
diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
index 565765c..cebc27e 100644
--- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
+++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
@@ -28,6 +28,7 @@
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+ MBUS_ID(0xf0, 0x02) 0xe0000000 0 0xe0000000 0x8100000
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x8000000>;
@@ -59,6 +60,15 @@
};
};
+ pcie-controller {
+ status = "okay";
+ /* Internal mini-PCIe connector */
+ pcie at 1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ };
+
internal-regs {
serial at 12000 {
clock-frequency = <250000000>;
@@ -172,15 +182,6 @@
usb at 51000 {
status = "okay";
};
-
- pcie-controller {
- status = "okay";
- /* Internal mini-PCIe connector */
- pcie at 1,0 {
- /* Port 0, Lane 0 */
- status = "okay";
- };
- };
};
};
};
--
1.8.1.5
More information about the linux-arm-kernel
mailing list