[PATCH v2 1/4] ARM: dts: omap4-panda: Add USB Host support

Tony Lindgren tony at atomide.com
Wed Jun 19 03:46:06 EDT 2013


* Roger Quadros <rogerq at ti.com> [130619 00:42]:
> Hi Benoit,
> 
> On 06/19/2013 04:17 AM, Benoit Cousson wrote:
> > Hi Roger,
> > 
> > On 06/18/2013 11:04 AM, Roger Quadros wrote:
> >> Provide the RESET and Power regulators for the USB PHY,
> >> the USB Host port mode and the PHY device.
> >>
> >> Also provide pin multiplexer information for the USB host
> >> pins.
> >>
> >> Signed-off-by: Roger Quadros <rogerq at ti.com>
> >> ---
> >>   arch/arm/boot/dts/omap4-panda-common.dtsi |   62 +++++++++++++++++++++++++++++
> >>   1 files changed, 62 insertions(+), 0 deletions(-)
> >>
> >> diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
> >> index 00cbaa5..7a21e8e 100644
> >> --- a/arch/arm/boot/dts/omap4-panda-common.dtsi
> >> +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
> >> @@ -59,6 +59,42 @@
> >>               "AFML", "Line In",
> >>               "AFMR", "Line In";
> >>       };
> >> +
> >> +    /* HS USB Port 1 RESET */
> >> +    hsusb1_reset: hsusb1_reset_reg {
> >> +        compatible = "regulator-fixed";
> >> +        regulator-name = "hsusb1_reset";
> >> +        regulator-min-microvolt = <3300000>;
> >> +        regulator-max-microvolt = <3300000>;
> >> +        gpio = <&gpio2 30 0>;    /* gpio_62 */
> >> +        startup-delay-us = <70000>;
> >> +        enable-active-high;
> >> +    };
> > 
> > Is this really a regulator? Or just a GPIO line used to reset the USB PHY?
> 
> It is in fact a GPIO line used as reset.
> > 
> > If this is the case, I don't think it should be represented as a regulator.
> 
> Why not? I think it fits very well in the regulator device model. I couldn't find a better
> way to represent this. It gives us a way to specify not only the GPIO line but also
> the polarity. I know mostly reset is active low but still there is flexibility as you never
> know for sure.

I think it's really a mux + a comparator. But from Linux driver point of view
a regulator fits well as we don't have anything better. After all, the pin
voltage changes, and then something can be done based on the comparator
value.
 
> Do you have any better ideas?

We have a similar issue with the MMC1 PBIAS. I think in the long run we
should expand regulator (and possibly pinctrl) framework(s) to handle
comparators. We could just assume that a comparatator is a regulator,
and have a comparator binding that just uses the regulator code.
 
> FYI. The USB PHY driver is already treating reset as a regulator and is into 3.10. Reworking that
> will take some time. Not getting these in will prevent USB host/ethernet support on panda.

Yes and we need to have some solution for v3.11 as we've dropped the
legacy data for omap4. Otherwise things won't work properly.

Regards,

Tony



More information about the linux-arm-kernel mailing list