[PATCH 1/2] Initial support for Allwinner's Security ID fuses

Oliver Schinagl oliver+list at schinagl.nl
Mon Jun 17 06:36:47 EDT 2013


On 15-06-13 12:28, Tomasz Figa wrote:
> Hi,
>
> Some comments inline.
Thank you
>
> On Saturday 15 of June 2013 01:16:20 Oliver Schinagl wrote:
>> From: Oliver Schinagl <oliver at schinagl.nl>
>>
>> Allwinner has electric fuses (efuse) on their line of chips. This driver
>> reads those fuses, seeds the kernel entropy and exports them as a sysfs
>> node.
>>
>> These fuses are most likly to be programmed at the factory, encoding
>> things like Chip ID, some sort of serial number etc and appear to be
>> reasonable unique.
>> While in theory, these should be writeable by the user, it will probably
>> be inconvinient to do so. Allwinner recommends that a certain input
>> pin, labeled 'efuse_vddq', be connected to GND. To write these fuses,
>> 2.5 V needs to be applied to this pin.
>>
>> Even so, they can still be used to generate a board-unique mac from,
>> board unique RSA key and seed the kernel RNG.
>>
>> Currently supported are the following known chips:
>> Allwinner sun4i (A10)
>> Allwinner sun5i (A10s, A13)
>>
>> Signed-off-by: Oliver Schinagl <oliver at schinagl.nl>
>> ---
>>   drivers/misc/eeprom/Kconfig     |  17 ++++
>>   drivers/misc/eeprom/Makefile    |   1 +
>>   drivers/misc/eeprom/sunxi_sid.c | 167
>> ++++++++++++++++++++++++++++++++++++++++ 3 files changed, 185
>> insertions(+)
>>   create mode 100644 drivers/misc/eeprom/sunxi_sid.c
>>
>> diff --git a/drivers/misc/eeprom/Kconfig b/drivers/misc/eeprom/Kconfig
>> index 04f2e1f..c7bc6ed 100644
>> --- a/drivers/misc/eeprom/Kconfig
>> +++ b/drivers/misc/eeprom/Kconfig
>> @@ -96,4 +96,21 @@ config EEPROM_DIGSY_MTC_CFG
>>
>>   	  If unsure, say N.
>>
>> +config EEPROM_SUNXI_SID
>> +	tristate "Allwinner sunxi security ID support"
>> +	depends on ARCH_SUNXI && SYSFS
>> +	help
>> +	  This is a driver for the 'security ID' available on various
>> Allwinner +	  devices. Currently supported are:
>> +		sun4i (A10)
>> +		sun5i (A13)
>> +
>> +	  Due to the potential risks involved with changing e-fuses,
>> +	  this driver is read-only
>> +
>> +	  For more information visit http://linux-sunxi.org/SID
>> +
>> +	  This driver can also be built as a module. If so, the module
>> +	  will be called sunxi_sid.
>> +
>>   endmenu
>> diff --git a/drivers/misc/eeprom/Makefile b/drivers/misc/eeprom/Makefile
>> index fc1e81d..9507aec 100644
>> --- a/drivers/misc/eeprom/Makefile
>> +++ b/drivers/misc/eeprom/Makefile
>> @@ -4,4 +4,5 @@ obj-$(CONFIG_EEPROM_LEGACY)	+= eeprom.o
>>   obj-$(CONFIG_EEPROM_MAX6875)	+= max6875.o
>>   obj-$(CONFIG_EEPROM_93CX6)	+= eeprom_93cx6.o
>>   obj-$(CONFIG_EEPROM_93XX46)	+= eeprom_93xx46.o
>> +obj-$(CONFIG_EEPROM_SUNXI_SID)	+= sunxi_sid.o
>>   obj-$(CONFIG_EEPROM_DIGSY_MTC_CFG) += digsy_mtc_eeprom.o
>> diff --git a/drivers/misc/eeprom/sunxi_sid.c
>> b/drivers/misc/eeprom/sunxi_sid.c new file mode 100644
>> index 0000000..f014e1b
>> --- /dev/null
>> +++ b/drivers/misc/eeprom/sunxi_sid.c
>> @@ -0,0 +1,167 @@
>> +/*
>> + * Copyright (c) 2013 Oliver Schinagl
>> + * http://www.linux-sunxi.org
>> + *
>> + * Oliver Schinagl <oliver at schinagl.nl>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published
>> by + * the Free Software Foundation; either version 2 of the License,
>> or + * (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * This driver exposes the Allwinner security ID, a 128 bit eeprom, in
>> byte + * sized chunks.
>> + */
>> +
>> +#include <linux/compiler.h>
>> +#include <linux/device.h>
>> +#include <linux/err.h>
>> +#include <linux/errno.h>
>> +#include <linux/export.h>
>> +#include <linux/fs.h>
>> +#include <linux/init.h>
>> +#include <linux/io.h>
>> +#include <linux/kernel.h>
>> +#include <linux/kobject.h>
>> +#include <linux/module.h>
>> +#include <linux/of_address.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/random.h>
>> +#include <linux/stat.h>
>> +#include <linux/sysfs.h>
>> +#include <linux/types.h>
>> +
>> +#define DRV_NAME "sunxi-sid"
>> +#define DRV_VERSION "1.0"
>
> What is this version thingy?
>
> Is there a versioning scheme defined for this driver? Do you expect it to
> be changed every modification of this driver?
>
> I don't see any point of having such thing in a project with a version
> control system, where you have all change history.
Well we export something to userspace, while trivial there is the 
possibility it changes over time. Say A40 which outputs 256 bits instead 
of the current 128 bits. That would validate a bump in version number. 
It's purely so the user can be aware of differences in the driver. So 
maybe DRV_A[BP]I_VERSION would be better?
>
>> +
>> +/* There are 4 32-bit keys */
>> +#define SID_KEYS 4
>> +/* and 4 byte sized keys per 32-bit key */
>> +#define SID_SIZE (SID_KEYS * 4)
>
>  From this definition it looks like there are just 4 32-bit keys, I don't
> see those extra four byte-sized keys accounted by this size.
I will change the comment, 'and 4 byte sized keys per SID' is probably 
better
The array is 128 bits split into 32 bit words. Each 32 bit word consists 
of 8 bits (1 byte).
So 4 * 4 = 16 bytes (SID_SIZE), is 128 bits.
>
>> +
>> +
>
> One _empty_ line is enough to separate definitions from code.
Okay, I find it personally a little clearer to separate them, but sure.
>
>> +/* We read the entire key, but only return the requested byte. This is
>> of + * course slower then it could be and uses 4 times more reads as
>> needed but + * keeps code simpler.
>
> I have no idea how often this is going to be read, but since the whole sid
> is really small (16 bytes), maybe it would be better to simply read the ID
> in probe to a buffer and then just memcpy from it in read().
The sid will be read once (well all 16 bytes) during probe and after 
that only on user request. Right now we don't have a user (yet) other 
then the sysfs entry.

In future, this key can be used to read the MAC (low reads) or AES keys 
for example (also low reads).

Initially I had such an approach, but Maxime recommended against having 
the value cached.

As I wrote to andy, the only 'more efficient' way would be to store the 
previously read key and see on the next read if its the same, So best 
case, we could save 4 reads. I think it makes the code unnecessarily 
complex for something that is read so little.
>
>> + */
>> +static u8 sunxi_sid_read_byte(const void __iomem *sid_reg_base,
>> +			      const unsigned int offset)
>> +{
>> +	u32 sid_key = 0;
>
> 	u32 sid_key; ...
Indeed, a left over from a previous version. It does no longer need to 
be initted.
>
>> +
>> +	if (offset >= SID_SIZE)
>> +		goto exit;
>
> 		return 0; ...
I did say in the changelog I opted for goto over return. But since 
everybody keeps preferring returns (I personally like 'one single exit 
point much more' I have already changed it all over to many returns, who 
am I to argue :)
>
>> +
>> +	sid_key = ioread32be(sid_reg_base + round_down(offset, 4));
>> +	sid_key >>= (offset % 4) * 8;
>> +	sid_key &= 0xff;
>> +	/* fall through */
>> +
>> +exit:
>
> ...and now magically here you can remove two unneeded lines.
>
>> +	return (u8)sid_key;
>
> Unnecessary casting.
Unnecessary because of the &= 0xff above, or because you can put a 32bit 
int in an 8bit int without worries? (we only want the last byte).
>
>> +}
>> +
>> +static ssize_t sid_read(struct file *fd, struct kobject *kobj,
>> +			struct bin_attribute *attr, char *buf,
>> +			loff_t pos, size_t size)
>> +{
>> +	int i;
>> +	struct platform_device *pdev;
>> +	void __iomem *sid_reg_base;
>> +
>> +	pdev = (struct platform_device
>> *)to_platform_device(kobj_to_dev(kobj)); +	sid_reg_base = (void
> __iomem
>> *)platform_get_drvdata(pdev);
>> +
>> +	for (i = 0; i < size; i++) {
>> +		if ((pos + i) >= SID_SIZE || (pos < 0))
>> +			break;
>> +		buf[i] = sunxi_sid_read_byte(sid_reg_base, pos + i);
>> +	}
>
> This could be greatly simplified if you just read the whole sid to memory
> in probe and memcpy from it here.
But can't because we don't want to cache it.
>
>> +	return i;
>> +}
>> +
>> +static const struct of_device_id sunxi_sid_of_match[] = {
>> +	{
>> +		.compatible = "allwinner,sun4i-sid",
>> +	},
>
> Above 3 lines could be put in single line.
okay
>
>> +	{/* sentinel */}
>> +};
>> +MODULE_DEVICE_TABLE(of, sunxi_sid_of_match);
>> +
>> +static const struct bin_attribute sid_bin_attr = {
>> +	.attr = {
>> +		.name = "eeprom",
>> +		.mode = S_IRUGO,
>> +	},
>> +	.size = SID_SIZE,
>> +	.read = sid_read,
>> +};
>> +
>> +static int sunxi_sid_remove(struct platform_device *pdev)
>> +{
>> +	device_remove_bin_file(&pdev->dev, &sid_bin_attr);
>> +	dev_info(&pdev->dev, "sunxi SID driver unloaded\n");
>
> Please either make this dev_dbg or remove it completely, as it is not
> something that users should be concerned about.
dev_dbg might be better for the remove, thanks
>
>> +	return 0;
>> +}
>> +
>> +static int __init sunxi_sid_probe(struct platform_device *pdev)
>> +{
>> +	int entropy[SID_SIZE], i;
>> +	struct resource *res;
>> +	void __iomem *sid_reg_base;
>> +	int ret;
>> +
>> +	if (!pdev->dev.of_node) {
>> +		dev_err(&pdev->dev, "No devicetree data available\n");
>> +		ret = -ENXIO;
>> +		goto exit;
>> +	}
>
> What is this check for? You don't seem to need anything from dev.of_node
> in this driver.
My understanding was, that when using the device tree, we check if the 
device tree is atleast available. And we use platform_get_resource, 
doesn't that get the data from the device tree?
>
>> +
>> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +	sid_reg_base = devm_ioremap_resource(&pdev->dev, res);
>> +	if (IS_ERR(sid_reg_base)) {
>> +		ret = PTR_ERR(sid_reg_base);
>> +		goto exit;
>> +	}
>
> One of the points of having devm_ helpers was removing the need to use
> error paths at functions end. You can save 2 lines of code by changing
> this check to:
>
> 	if (IS_ERR(sid_reg_base))
> 		return PTR_ERR(sid_reg_base);
Okay
>
>> +	platform_set_drvdata(pdev, sid_reg_base);
>> +
>> +	ret = device_create_bin_file(&pdev->dev, &sid_bin_attr);
>> +	if (ret) {
>> +		dev_err(&pdev->dev, "Unable to create sysfs bin entry\n");
>> +		goto exit;
>> +	}
>
> Same here.
Yeah, many returns, check
>
>> +
>> +	for (i = 0; i < SID_SIZE; i++)
>> +		entropy[i] = sunxi_sid_read_byte(sid_reg_base, i);
>
> You seem to read bytes into an array of ints. Your entropy data will
> always have most significant 24-bits cleared. Is this behavior correct?
Yes, though I changed it so that entropy is an array of u8's, since 
that's what sunxi_sid_read_byte returns.
>
>> +	add_device_randomness(entropy, SID_SIZE);
>
> Now I'm pretty sure that above is not the correct behavior. You are adding
> here first 16 bytes (=SID_SIZE) of entropy[], while it is an array of 16
> ints (=4*SID_SIZE)...
Well technically, doesn't to compiler see that entropy is never larger 
then 8 bits and thus uses only 8 bits? uint8_atleast or something. But 
yeah, it's better to use the specified size to not waste 24 empty bits.
>
>> +	dev_info(&pdev->dev, "sunxi SID ver %s loaded\n", DRV_VERSION);
>
> Same comment as for the message in remove().
Though with the DRV_(A[BP]I_)VERSION this is purly informational, I 
changed it to only show in the dev_dbg as requested.
>
>> +	ret = 0;
>> +	/* fall through */
>> +
>> +exit:
>> +	return ret;
>
> Above 4 non-empty lines can be replaced by a single
>
> 	return 0;
>
>> +}
>> +
>> +static struct platform_driver sunxi_sid_driver = {
>> +	.probe = sunxi_sid_probe,
>> +	.remove = sunxi_sid_remove,
>> +	.driver = {
>> +		.name = DRV_NAME,
>> +		.owner = THIS_MODULE,
>> +		.of_match_table = sunxi_sid_of_match,
>> +	},
>> +};
>> +module_platform_driver(sunxi_sid_driver);
>> +
>> +
>
> One empty line is enough.
Okay
>
> Best regards,
> Tomasz
>
>> +MODULE_AUTHOR("Oliver Schinagl <oliver at schinagl.nl>");
>> +MODULE_DESCRIPTION("Allwinner sunxi security id driver");
>> +MODULE_VERSION(DRV_VERSION);
>> +MODULE_LICENSE("GPL");




More information about the linux-arm-kernel mailing list