[PATCH] pinctrl: establish pull-up/pull-down terminology

Linus Walleij linus.walleij at stericsson.com
Sun Jun 16 06:45:48 EDT 2013


From: Linus Walleij <linus.walleij at linaro.org>

It is counter-intuitive to have "0" mean disable in a boolean
manner for electronic properties of pins such as pull-up and
pull-down. Therefore, define that a pull-up/pull-down argument
of 0 to such a generic option means that the pin is
short-circuited to VDD or GROUND. Pull disablement shall be
done using PIN_CONFIG_BIAS_DISABLE.

Cc: Heiko Stübner <heiko at sntech.de>
Cc: James Hogan <james.hogan at imgtec.com>
Cc: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
 include/linux/pinctrl/pinconf-generic.h | 13 +++++++------
 1 file changed, 7 insertions(+), 6 deletions(-)

diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
index d414a77..67780f5 100644
--- a/include/linux/pinctrl/pinconf-generic.h
+++ b/include/linux/pinctrl/pinconf-generic.h
@@ -36,14 +36,15 @@
  *	tristate. The argument is ignored.
  * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
  *	impedance to VDD). If the argument is != 0 pull-up is enabled,
- *	if it is 0, pull-up is disabled.
+ *	if it is 0, pull-up it total, i.e. the pin is connected to VDD.
  * @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high
  *	impedance to GROUND). If the argument is != 0 pull-down is enabled,
- *	if it is 0, pull-down is disabled.
+ *	if it is 0, pull-down is total, i.e. the pin is connected to GROUND.
  * @PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: the pin will be pulled up or down based
  *	on embedded knowledge of the controller, like current mux function.
- *	If the argument is != 0 pull up/down is enabled, if it is 0,
- *	the pull is disabled.
+ *	If the argument is != 0 pull up/down is enabled, if it is 0, the
+ *	configuration is ignored. The proper way to disable it is to use
+ *	@PIN_CONFIG_BIAS_DISABLE.
  * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and
  *	low, this is the most typical case and is typically achieved with two
  *	active transistors on the output. Setting this config will enable
@@ -72,8 +73,8 @@
  *	supplies, the argument to this parameter (on a custom format) tells
  *	the driver which alternative power source to use.
  * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
- * 	this parameter (on a custom format) tells the driver which alternative
- * 	slew rate to use.
+ *	this parameter (on a custom format) tells the driver which alternative
+ *	slew rate to use.
  * @PIN_CONFIG_LOW_POWER_MODE: this will configure the pin for low power
  *	operation, if several modes of operation are supported these can be
  *	passed in the argument on a custom form, else just use argument 1
-- 
1.7.11.3




More information about the linux-arm-kernel mailing list