[PATCH 04/12] phy-rcar-usb: remove EHCI internal buffer setup

Simon Horman horms+renesas at verge.net.au
Thu Jun 13 03:00:28 EDT 2013


From: Sergei Shtylyov <sergei.shtylyov at cogentembedded.com>

Now that the EHCI internal  buffer setup is done by the platform code,  we  can
remove  such code from this driver as it  never  really belonged here.  We also
no longer need the 2nd memory region now (2nd EHCI controller is simply missing
in e.g. R8A7778 SoC).

The patch has been tested on the Marzen and BOCK-W boards.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov at cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx at renesas.com>
Acked-by: Felipe Balbi <balbi at ti.com>
Signed-off-by: Simon Horman <horms+renesas at verge.net.au>
---
 drivers/usb/phy/phy-rcar-usb.c | 28 ++++------------------------
 1 file changed, 4 insertions(+), 24 deletions(-)

diff --git a/drivers/usb/phy/phy-rcar-usb.c b/drivers/usb/phy/phy-rcar-usb.c
index a35681b..4893dbd 100644
--- a/drivers/usb/phy/phy-rcar-usb.c
+++ b/drivers/usb/phy/phy-rcar-usb.c
@@ -23,8 +23,6 @@
 #define USBEH0		0x080C
 #define USBOH0		0x081C
 #define USBCTL0		0x0858
-#define EIIBC1		0x0094
-#define EIIBC2		0x009C
 
 /* USBPCTRL1 */
 #define PHY_RST		(1 << 2)
@@ -40,7 +38,6 @@ struct rcar_usb_phy_priv {
 	spinlock_t lock;
 
 	void __iomem *reg0;
-	void __iomem *reg1;
 	int counter;
 };
 
@@ -59,7 +56,6 @@ static int rcar_usb_phy_init(struct usb_phy *phy)
 	struct rcar_usb_phy_priv *priv = usb_phy_to_priv(phy);
 	struct device *dev = phy->dev;
 	void __iomem *reg0 = priv->reg0;
-	void __iomem *reg1 = priv->reg1;
 	int i;
 	u32 val;
 	unsigned long flags;
@@ -97,19 +93,6 @@ static int rcar_usb_phy_init(struct usb_phy *phy)
 		iowrite32(0x00000000, (reg0 + USBPCTRL0));
 
 		/*
-		 * EHCI IP internal buffer setting
-		 * EHCI IP internal buffer enable
-		 *
-		 * These are recommended value of a datasheet
-		 * see [USB :: EHCI internal buffer setting]
-		 */
-		iowrite32(0x00ff0040, (reg0 + EIIBC1));
-		iowrite32(0x00ff0040, (reg1 + EIIBC1));
-
-		iowrite32(0x00000001, (reg0 + EIIBC2));
-		iowrite32(0x00000001, (reg1 + EIIBC2));
-
-		/*
 		 * Bus alignment settings
 		 */
 
@@ -145,14 +128,13 @@ static void rcar_usb_phy_shutdown(struct usb_phy *phy)
 static int rcar_usb_phy_probe(struct platform_device *pdev)
 {
 	struct rcar_usb_phy_priv *priv;
-	struct resource *res0, *res1;
+	struct resource *res0;
 	struct device *dev = &pdev->dev;
-	void __iomem *reg0, *reg1;
+	void __iomem *reg0;
 	int ret;
 
 	res0 = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	res1 = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	if (!res0 || !res1) {
+	if (!res0) {
 		dev_err(dev, "Not enough platform resources\n");
 		return -EINVAL;
 	}
@@ -164,8 +146,7 @@ static int rcar_usb_phy_probe(struct platform_device *pdev)
 	 * this driver can't use devm_request_and_ioremap(dev, res) here
 	 */
 	reg0 = devm_ioremap_nocache(dev, res0->start, resource_size(res0));
-	reg1 = devm_ioremap_nocache(dev, res1->start, resource_size(res1));
-	if (!reg0 || !reg1) {
+	if (!reg0) {
 		dev_err(dev, "ioremap error\n");
 		return -ENOMEM;
 	}
@@ -177,7 +158,6 @@ static int rcar_usb_phy_probe(struct platform_device *pdev)
 	}
 
 	priv->reg0		= reg0;
-	priv->reg1		= reg1;
 	priv->counter		= 0;
 	priv->phy.dev		= dev;
 	priv->phy.label		= dev_name(dev);
-- 
1.8.2.1




More information about the linux-arm-kernel mailing list