[RFC PATCH 1/1] ARM: at91: drop rm9200dk board support

Jean-Christophe PLAGNIOL-VILLARD plagnioj at jcrosoft.com
Mon Jun 10 10:42:25 EDT 2013


This board is impossible to found anymore

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre at atmel.com>
---
 arch/arm/configs/at91rm9200_defconfig |    1 -
 arch/arm/mach-at91/Kconfig.non_dt     |    7 -
 arch/arm/mach-at91/Makefile           |    1 -
 arch/arm/mach-at91/board-rm9200dk.c   |  228 ---------------------------------
 4 files changed, 237 deletions(-)
 delete mode 100644 arch/arm/mach-at91/board-rm9200dk.c

diff --git a/arch/arm/configs/at91rm9200_defconfig b/arch/arm/configs/at91rm9200_defconfig
index 43834a7..3b76a63 100644
--- a/arch/arm/configs/at91rm9200_defconfig
+++ b/arch/arm/configs/at91rm9200_defconfig
@@ -17,7 +17,6 @@ CONFIG_MODULE_SRCVERSION_ALL=y
 # CONFIG_IOSCHED_CFQ is not set
 CONFIG_ARCH_AT91=y
 CONFIG_ARCH_AT91RM9200=y
-CONFIG_ARCH_AT91RM9200DK=y
 CONFIG_MACH_AT91RM9200EK=y
 CONFIG_MACH_CSB337=y
 CONFIG_MACH_CSB637=y
diff --git a/arch/arm/mach-at91/Kconfig.non_dt b/arch/arm/mach-at91/Kconfig.non_dt
index 8d84324..867c547 100644
--- a/arch/arm/mach-at91/Kconfig.non_dt
+++ b/arch/arm/mach-at91/Kconfig.non_dt
@@ -56,13 +56,6 @@ if ARCH_AT91RM9200
 
 comment "AT91RM9200 Board Type"
 
-config ARCH_AT91RM9200DK
-	bool "Atmel AT91RM9200-DK Development board"
-	select HAVE_AT91_DATAFLASH_CARD
-	help
-	  Select this if you are using Atmel's AT91RM9200-DK Development board.
-	  (Discontinued)
-
 config MACH_AT91RM9200EK
 	bool "Atmel AT91RM9200-EK Evaluation Kit"
 	select HAVE_AT91_DATAFLASH_CARD
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 1429985..dc2308b 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -33,7 +33,6 @@ obj-$(CONFIG_ARCH_AT91SAM9G45)	+= at91sam9g45_devices.o
 obj-$(CONFIG_ARCH_AT91X40)	+= at91x40.o at91x40_time.o
 
 # AT91RM9200 board-specific support
-obj-$(CONFIG_ARCH_AT91RM9200DK)	+= board-rm9200dk.o
 obj-$(CONFIG_MACH_AT91RM9200EK)	+= board-rm9200ek.o
 obj-$(CONFIG_MACH_CSB337)	+= board-csb337.o
 obj-$(CONFIG_MACH_CSB637)	+= board-csb637.o
diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c
deleted file mode 100644
index 690541b..0000000
--- a/arch/arm/mach-at91/board-rm9200dk.c
+++ /dev/null
@@ -1,228 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-rm9200dk.c
- *
- *  Copyright (C) 2005 SAN People
- *
- *  Epson S1D framebuffer glue code is:
- *     Copyright (C) 2005 Thibaut VARENE <varenet at parisc-linux.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91_ramc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-
-
-static void __init dk_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-static struct macb_platform_data __initdata dk_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PC4,
-	.is_rmii	= 1,
-};
-
-static struct at91_usbh_data __initdata dk_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata dk_udc_data = {
-	.vbus_pin	= AT91_PIN_PD4,
-	.pullup_pin	= AT91_PIN_PD5,
-};
-
-static struct at91_cf_data __initdata dk_cf_data = {
-	.irq_pin	= -EINVAL,
-	.det_pin	= AT91_PIN_PB0,
-	.vcc_pin	= -EINVAL,
-	.rst_pin	= AT91_PIN_PC5,
-};
-
-#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
-static struct mci_platform_data __initdata dk_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= -EINVAL,
-		.wp_pin		= -EINVAL,
-	},
-};
-#endif
-
-static struct spi_board_info dk_spi_devices[] = {
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-	},
-	{	/* UR6HCPS2-SP40 PS2-to-SPI adapter */
-		.modalias	= "ur6hcps2",
-		.chip_select	= 1,
-		.max_speed_hz	= 250 *  1000,
-	},
-	{	/* TLV1504 ADC, 4 channels, 10 bits; one is a temp sensor */
-		.modalias	= "tlv1504",
-		.chip_select	= 2,
-		.max_speed_hz	= 20 * 1000 * 1000,
-	},
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-	{	/* DataFlash card */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 3,
-		.max_speed_hz	= 15 * 1000 * 1000,
-	}
-#endif
-};
-
-static struct i2c_board_info __initdata dk_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("ics1523", 0x26),
-	},
-	{
-		I2C_BOARD_INFO("x9429", 0x28),
-	},
-	{
-		I2C_BOARD_INFO("24c1024", 0x50),
-	}
-};
-
-static struct mtd_partition __initdata dk_nand_partition[] = {
-	{
-		.name	= "NAND Partition 1",
-		.offset	= 0,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct atmel_nand_data __initdata dk_nand_data = {
-	.ale		= 22,
-	.cle		= 21,
-	.det_pin	= AT91_PIN_PB1,
-	.rdy_pin	= AT91_PIN_PC2,
-	.enable_pin	= -EINVAL,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.on_flash_bbt	= 1,
-	.parts		= dk_nand_partition,
-	.num_parts	= ARRAY_SIZE(dk_nand_partition),
-};
-
-#define DK_FLASH_BASE	AT91_CHIPSELECT_0
-#define DK_FLASH_SIZE	SZ_2M
-
-static struct physmap_flash_data dk_flash_data = {
-	.width		= 2,
-};
-
-static struct resource dk_flash_resource = {
-	.start		= DK_FLASH_BASE,
-	.end		= DK_FLASH_BASE + DK_FLASH_SIZE - 1,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device dk_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-				.platform_data	= &dk_flash_data,
-			},
-	.resource	= &dk_flash_resource,
-	.num_resources	= 1,
-};
-
-static struct gpio_led dk_leds[] = {
-	{
-		.name			= "led0",
-		.gpio			= AT91_PIN_PB2,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-static void __init dk_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-	at91_add_device_serial();
-	/* Ethernet */
-	at91_add_device_eth(&dk_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&dk_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&dk_udc_data);
-	at91_set_multi_drive(dk_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
-	/* Compact Flash */
-	at91_add_device_cf(&dk_cf_data);
-	/* I2C */
-	at91_add_device_i2c(dk_i2c_devices, ARRAY_SIZE(dk_i2c_devices));
-	/* SPI */
-	at91_add_device_spi(dk_spi_devices, ARRAY_SIZE(dk_spi_devices));
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-	/* DataFlash card */
-	at91_set_gpio_output(AT91_PIN_PB7, 0);
-#else
-	/* MMC */
-	at91_set_gpio_output(AT91_PIN_PB7, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
-	at91_add_device_mci(0, &dk_mci0_data);
-#endif
-	/* NAND */
-	at91_add_device_nand(&dk_nand_data);
-	/* NOR Flash */
-	platform_device_register(&dk_flash);
-	/* LEDs */
-	at91_gpio_leds(dk_leds, ARRAY_SIZE(dk_leds));
-	/* VGA */
-//	dk_add_device_video();
-}
-
-MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK")
-	/* Maintainer: SAN People/Atmel */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= dk_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= dk_board_init,
-MACHINE_END
-- 
1.7.10.4




More information about the linux-arm-kernel mailing list