[PATCH 14/14] ARM: mvebu: Relocate Armada XP PCIe device tree nodes

Ezequiel Garcia ezequiel.garcia at free-electrons.com
Fri Jun 7 12:47:51 EDT 2013


Now that mbus has been added to the device tree, it's possible to
move the PCIe nodes out of internal registers, placing it directly
below the mbus. This is a more accurate representation of the
hardware.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia at free-electrons.com>
---
 arch/arm/boot/dts/armada-xp-db.dts               |  66 ++--
 arch/arm/boot/dts/armada-xp-gp.dts               |  42 +--
 arch/arm/boot/dts/armada-xp-mv78230.dtsi         | 209 ++++++-------
 arch/arm/boot/dts/armada-xp-mv78260.dtsi         | 245 +++++++--------
 arch/arm/boot/dts/armada-xp-mv78460.dtsi         | 377 ++++++++++++-----------
 arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts |  18 +-
 6 files changed, 480 insertions(+), 477 deletions(-)

diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts
index d6cc8bf..32e25fe 100644
--- a/arch/arm/boot/dts/armada-xp-db.dts
+++ b/arch/arm/boot/dts/armada-xp-db.dts
@@ -30,6 +30,39 @@
 	};
 
 	soc {
+		pcie-controller {
+			status = "okay";
+
+			/*
+			 * All 6 slots are physically present as
+			 * standard PCIe slots on the board.
+			 */
+			pcie at 1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+			pcie at 2,0 {
+				/* Port 0, Lane 1 */
+				status = "okay";
+			};
+			pcie at 3,0 {
+				/* Port 0, Lane 2 */
+				status = "okay";
+			};
+			pcie at 4,0 {
+				/* Port 0, Lane 3 */
+				status = "okay";
+			};
+			pcie at 9,0 {
+				/* Port 2, Lane 0 */
+				status = "okay";
+			};
+			pcie at 10,0 {
+				/* Port 3, Lane 0 */
+				status = "okay";
+			};
+		};
+
 		internal-regs {
 			serial at 12000 {
 				clock-frequency = <250000000>;
@@ -122,39 +155,6 @@
 					spi-max-frequency = <20000000>;
 				};
 			};
-
-			pcie-controller {
-				status = "okay";
-
-				/*
-				 * All 6 slots are physically present as
-				 * standard PCIe slots on the board.
-				 */
-				pcie at 1,0 {
-					/* Port 0, Lane 0 */
-					status = "okay";
-				};
-				pcie at 2,0 {
-					/* Port 0, Lane 1 */
-					status = "okay";
-				};
-				pcie at 3,0 {
-					/* Port 0, Lane 2 */
-					status = "okay";
-				};
-				pcie at 4,0 {
-					/* Port 0, Lane 3 */
-					status = "okay";
-				};
-				pcie at 9,0 {
-					/* Port 2, Lane 0 */
-					status = "okay";
-				};
-				pcie at 10,0 {
-					/* Port 3, Lane 0 */
-					status = "okay";
-				};
-			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts
index d045d6e..333dd3b 100644
--- a/arch/arm/boot/dts/armada-xp-gp.dts
+++ b/arch/arm/boot/dts/armada-xp-gp.dts
@@ -68,6 +68,27 @@
 			};
 		};
 
+		pcie-controller {
+			status = "okay";
+
+			/*
+			 * The 3 slots are physically present as
+			 * standard PCIe slots on the board.
+			 */
+			pcie at 1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+			pcie at 9,0 {
+				/* Port 2, Lane 0 */
+				status = "okay";
+			};
+			pcie at 10,0 {
+				/* Port 3, Lane 0 */
+				status = "okay";
+			};
+		};
+
 		internal-regs {
 			serial at 12000 {
 				clock-frequency = <250000000>;
@@ -141,27 +162,6 @@
 					spi-max-frequency = <108000000>;
 				};
 			};
-
-			pcie-controller {
-				status = "okay";
-
-				/*
-				 * The 3 slots are physically present as
-				 * standard PCIe slots on the board.
-				 */
-				pcie at 1,0 {
-					/* Port 0, Lane 0 */
-					status = "okay";
-				};
-				pcie at 9,0 {
-					/* Port 2, Lane 0 */
-					status = "okay";
-				};
-				pcie at 10,0 {
-					/* Port 3, Lane 0 */
-					status = "okay";
-				};
-			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
index f8eaa38..e0265e5 100644
--- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
@@ -44,6 +44,111 @@
 	};
 
 	soc {
+		/*
+		 * MV78230 has 2 PCIe units Gen2.0: One unit can be
+		 * configured as x4 or quad x1 lanes. One unit is
+		 * x4/x1.
+		 */
+		pcie-controller {
+			compatible = "marvell,armada-xp-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x40000 0 0x40000 0 0x00002000   /* Port 0.0 registers */
+				0x82000000 0 0x42000 0 0x42000 0 0x00002000   /* Port 2.0 registers */
+				0x82000000 0 0x44000 0 0x44000 0 0x00002000   /* Port 0.1 registers */
+				0x82000000 0 0x48000 0 0x48000 0 0x00002000   /* Port 0.2 registers */
+				0x82000000 0 0x4c000 0 0x4c000 0 0x00002000   /* Port 0.3 registers */
+				0x82000000 0 0xe0000000 0xffff0000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
+				0x81000000 0 0	  0xffff0000 0xe8000000 0 0x00100000>; /* downstream I/O */
+
+			pcie at 1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 58>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			pcie at 2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 59>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <1>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+
+			pcie at 3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				reg = <0x1800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 60>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <2>;
+				clocks = <&gateclk 7>;
+				status = "disabled";
+			};
+
+			pcie at 4,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+				reg = <0x2000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 61>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <3>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			pcie at 9,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+				reg = <0x4800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 99>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 26>;
+				status = "disabled";
+			};
+		};
+
 		internal-regs {
 			pinctrl {
 				compatible = "marvell,mv78230-pinctrl";
@@ -77,110 +182,6 @@
 				#interrupts-cells = <2>;
 				interrupts = <87>, <88>, <89>;
 			};
-
-			/*
-			 * MV78230 has 2 PCIe units Gen2.0: One unit can be
-			 * configured as x4 or quad x1 lanes. One unit is
-			 * x4/x1.
-			 */
-			pcie-controller {
-				compatible = "marvell,armada-xp-pcie";
-				status = "disabled";
-				device_type = "pci";
-
-#address-cells = <3>;
-#size-cells = <2>;
-
-				bus-range = <0x00 0xff>;
-
-				ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000   /* Port 0.0 registers */
-					0x82000000 0 0x42000 0x42000 0 0x00002000   /* Port 2.0 registers */
-					0x82000000 0 0x44000 0x44000 0 0x00002000   /* Port 0.1 registers */
-					0x82000000 0 0x48000 0x48000 0 0x00002000   /* Port 0.2 registers */
-					0x82000000 0 0x4c000 0x4c000 0 0x00002000   /* Port 0.3 registers */
-					0x82000000 0 0xe0000000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
-					0x81000000 0 0	  0xe8000000 0 0x00100000>; /* downstream I/O */
-
-				pcie at 1,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
-					reg = <0x0800 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 58>;
-					marvell,pcie-port = <0>;
-					marvell,pcie-lane = <0>;
-					clocks = <&gateclk 5>;
-					status = "disabled";
-				};
-
-				pcie at 2,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
-					reg = <0x1000 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 59>;
-					marvell,pcie-port = <0>;
-					marvell,pcie-lane = <1>;
-					clocks = <&gateclk 6>;
-					status = "disabled";
-				};
-
-				pcie at 3,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
-					reg = <0x1800 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 60>;
-					marvell,pcie-port = <0>;
-					marvell,pcie-lane = <2>;
-					clocks = <&gateclk 7>;
-					status = "disabled";
-				};
-
-				pcie at 4,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
-					reg = <0x2000 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 61>;
-					marvell,pcie-port = <0>;
-					marvell,pcie-lane = <3>;
-					clocks = <&gateclk 8>;
-					status = "disabled";
-				};
-
-				pcie at 9,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
-					reg = <0x4800 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 99>;
-					marvell,pcie-port = <2>;
-					marvell,pcie-lane = <0>;
-					clocks = <&gateclk 26>;
-					status = "disabled";
-				};
-			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
index f4029f0..f2bb74b 100644
--- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
@@ -45,6 +45,129 @@
 	};
 
 	soc {
+		/*
+		 * MV78260 has 3 PCIe units Gen2.0: Two units can be
+		 * configured as x4 or quad x1 lanes. One unit is
+		 * x4/x1.
+		 */
+		pcie-controller {
+			compatible = "marvell,armada-xp-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x40000 0 0x40000 0 0x00002000   /* Port 0.0 registers */
+				0x82000000 0 0x42000 0 0x42000 0 0x00002000   /* Port 2.0 registers */
+				0x82000000 0 0x44000 0 0x44000 0 0x00002000   /* Port 0.1 registers */
+				0x82000000 0 0x48000 0 0x48000 0 0x00002000   /* Port 0.2 registers */
+				0x82000000 0 0x4c000 0 0x4c000 0 0x00002000   /* Port 0.3 registers */
+				0x82000000 0 0x80000 0 0x80000 0 0x00002000   /* Port 1.0 registers */
+				0x82000000 0 0x82000 0 0x82000 0 0x00002000   /* Port 3.0 registers */
+				0x82000000 0 0xe0000000 0xffff0000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
+				0x81000000 0 0	  0xffff0000 0xe8000000 0 0x00100000>; /* downstream I/O */
+
+			pcie at 1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 58>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			pcie at 2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 59>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <1>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+
+			pcie at 3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				reg = <0x1800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 60>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <2>;
+				clocks = <&gateclk 7>;
+				status = "disabled";
+			};
+
+			pcie at 4,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+				reg = <0x2000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 61>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <3>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			pcie at 9,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+				reg = <0x4800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 99>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 26>;
+				status = "disabled";
+			};
+
+			pcie at 10,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x82000 0 0x2000>;
+				reg = <0x5000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 103>;
+				marvell,pcie-port = <3>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 27>;
+				status = "disabled";
+			};
+		};
+
 		internal-regs {
 			pinctrl {
 				compatible = "marvell,mv78260-pinctrl";
@@ -97,128 +220,6 @@
 				clocks = <&gateclk 1>;
 				status = "disabled";
 			};
-
-			/*
-			 * MV78260 has 3 PCIe units Gen2.0: Two units can be
-			 * configured as x4 or quad x1 lanes. One unit is
-			 * x4/x1.
-			 */
-			pcie-controller {
-				compatible = "marvell,armada-xp-pcie";
-				status = "disabled";
-				device_type = "pci";
-
-				#address-cells = <3>;
-				#size-cells = <2>;
-
-				bus-range = <0x00 0xff>;
-
-				ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000   /* Port 0.0 registers */
-					0x82000000 0 0x42000 0x42000 0 0x00002000   /* Port 2.0 registers */
-					0x82000000 0 0x44000 0x44000 0 0x00002000   /* Port 0.1 registers */
-					0x82000000 0 0x48000 0x48000 0 0x00002000   /* Port 0.2 registers */
-					0x82000000 0 0x4c000 0x4c000 0 0x00002000   /* Port 0.3 registers */
-					0x82000000 0 0x80000 0x80000 0 0x00002000   /* Port 1.0 registers */
-					0x82000000 0 0x82000 0x82000 0 0x00002000   /* Port 3.0 registers */
-					0x82000000 0 0xe0000000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
-					0x81000000 0 0	  0xe8000000 0 0x00100000>; /* downstream I/O */
-
-				pcie at 1,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
-					reg = <0x0800 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 58>;
-					marvell,pcie-port = <0>;
-					marvell,pcie-lane = <0>;
-					clocks = <&gateclk 5>;
-					status = "disabled";
-				};
-
-				pcie at 2,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
-					reg = <0x1000 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 59>;
-					marvell,pcie-port = <0>;
-					marvell,pcie-lane = <1>;
-					clocks = <&gateclk 6>;
-					status = "disabled";
-				};
-
-				pcie at 3,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
-					reg = <0x1800 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 60>;
-					marvell,pcie-port = <0>;
-					marvell,pcie-lane = <2>;
-					clocks = <&gateclk 7>;
-					status = "disabled";
-				};
-
-				pcie at 4,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
-					reg = <0x2000 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 61>;
-					marvell,pcie-port = <0>;
-					marvell,pcie-lane = <3>;
-					clocks = <&gateclk 8>;
-					status = "disabled";
-				};
-
-				pcie at 9,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
-					reg = <0x4800 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 99>;
-					marvell,pcie-port = <2>;
-					marvell,pcie-lane = <0>;
-					clocks = <&gateclk 26>;
-					status = "disabled";
-				};
-
-				pcie at 10,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82000800 0 0x82000 0 0x2000>;
-					reg = <0x5000 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 103>;
-					marvell,pcie-port = <3>;
-					marvell,pcie-lane = <0>;
-					clocks = <&gateclk 27>;
-					status = "disabled";
-				};
-			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
index 488ca5e..21376c8 100644
--- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
@@ -60,6 +60,195 @@
 	};
 
 	soc {
+		/*
+		 * MV78460 has 4 PCIe units Gen2.0: Two units can be
+		 * configured as x4 or quad x1 lanes. Two units are
+		 * x4/x1.
+		 */
+		pcie-controller {
+			compatible = "marvell,armada-xp-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x40000 0 0x40000 0 0x00002000   /* Port 0.0 registers */
+				0x82000000 0 0x42000 0 0x42000 0 0x00002000   /* Port 2.0 registers */
+				0x82000000 0 0x44000 0 0x44000 0 0x00002000   /* Port 0.1 registers */
+				0x82000000 0 0x48000 0 0x48000 0 0x00002000   /* Port 0.2 registers */
+				0x82000000 0 0x4c000 0 0x4c000 0 0x00002000   /* Port 0.3 registers */
+				0x82000000 0 0x80000 0 0x80000 0 0x00002000   /* Port 1.0 registers */
+				0x82000000 0 0x82000 0 0x82000 0 0x00002000   /* Port 3.0 registers */
+				0x82000000 0 0x84000 0 0x84000 0 0x00002000   /* Port 1.1 registers */
+				0x82000000 0 0x88000 0 0x88000 0 0x00002000   /* Port 1.2 registers */
+				0x82000000 0 0x8c000 0 0x8c000 0 0x00002000   /* Port 1.3 registers */
+				0x82000000 0 0xe0000000 0xffff0000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
+				0x81000000 0 0	  0xffff0000 0xe8000000 0 0x00100000>; /* downstream I/O */
+
+			pcie at 1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 58>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			pcie at 2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 59>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <1>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+
+			pcie at 3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
+				reg = <0x1800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 60>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <2>;
+				clocks = <&gateclk 7>;
+				status = "disabled";
+			};
+
+			pcie at 4,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
+				reg = <0x2000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 61>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <3>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			pcie at 5,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+				reg = <0x2800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 62>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 9>;
+				status = "disabled";
+			};
+
+			pcie at 6,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
+				reg = <0x3000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 63>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <1>;
+				clocks = <&gateclk 10>;
+				status = "disabled";
+			};
+
+			pcie at 7,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
+				reg = <0x3800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 64>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <2>;
+				clocks = <&gateclk 11>;
+				status = "disabled";
+			};
+
+			pcie at 8,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
+				reg = <0x4000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 65>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <3>;
+				clocks = <&gateclk 12>;
+				status = "disabled";
+			};
+			pcie at 9,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
+				reg = <0x4800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 99>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 26>;
+				status = "disabled";
+			};
+
+			pcie at 10,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
+				reg = <0x5000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 103>;
+				marvell,pcie-port = <3>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 27>;
+				status = "disabled";
+			};
+		};
+
 		internal-regs {
 			pinctrl {
 				compatible = "marvell,mv78460-pinctrl";
@@ -112,194 +301,6 @@
 				clocks = <&gateclk 1>;
 				status = "disabled";
 			};
-
-			/*
-			 * MV78460 has 4 PCIe units Gen2.0: Two units can be
-			 * configured as x4 or quad x1 lanes. Two units are
-			 * x4/x1.
-			 */
-			pcie-controller {
-				compatible = "marvell,armada-xp-pcie";
-				status = "disabled";
-				device_type = "pci";
-
-				#address-cells = <3>;
-				#size-cells = <2>;
-
-				bus-range = <0x00 0xff>;
-
-				ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000   /* Port 0.0 registers */
-					0x82000000 0 0x42000 0x42000 0 0x00002000   /* Port 2.0 registers */
-					0x82000000 0 0x44000 0x44000 0 0x00002000   /* Port 0.1 registers */
-					0x82000000 0 0x48000 0x48000 0 0x00002000   /* Port 0.2 registers */
-					0x82000000 0 0x4c000 0x4c000 0 0x00002000   /* Port 0.3 registers */
-					0x82000000 0 0x80000 0x80000 0 0x00002000   /* Port 1.0 registers */
-					0x82000000 0 0x82000 0x82000 0 0x00002000   /* Port 3.0 registers */
-					0x82000000 0 0x84000 0x84000 0 0x00002000   /* Port 1.1 registers */
-					0x82000000 0 0x88000 0x88000 0 0x00002000   /* Port 1.2 registers */
-					0x82000000 0 0x8c000 0x8c000 0 0x00002000   /* Port 1.3 registers */
-					0x82000000 0 0xe0000000 0xe0000000 0 0x08000000   /* non-prefetchable memory */
-					0x81000000 0 0	  0xe8000000 0 0x00100000>; /* downstream I/O */
-
-				pcie at 1,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
-					reg = <0x0800 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 58>;
-					marvell,pcie-port = <0>;
-					marvell,pcie-lane = <0>;
-					clocks = <&gateclk 5>;
-					status = "disabled";
-				};
-
-				pcie at 2,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
-					reg = <0x1000 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 59>;
-					marvell,pcie-port = <0>;
-					marvell,pcie-lane = <1>;
-					clocks = <&gateclk 6>;
-					status = "disabled";
-				};
-
-				pcie at 3,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
-					reg = <0x1800 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 60>;
-					marvell,pcie-port = <0>;
-					marvell,pcie-lane = <2>;
-					clocks = <&gateclk 7>;
-					status = "disabled";
-				};
-
-				pcie at 4,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
-					reg = <0x2000 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 61>;
-					marvell,pcie-port = <0>;
-					marvell,pcie-lane = <3>;
-					clocks = <&gateclk 8>;
-					status = "disabled";
-				};
-
-				pcie at 5,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
-					reg = <0x2800 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 62>;
-					marvell,pcie-port = <1>;
-					marvell,pcie-lane = <0>;
-					clocks = <&gateclk 9>;
-					status = "disabled";
-				};
-
-				pcie at 6,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
-					reg = <0x3000 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 63>;
-					marvell,pcie-port = <1>;
-					marvell,pcie-lane = <1>;
-					clocks = <&gateclk 10>;
-					status = "disabled";
-				};
-
-				pcie at 7,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
-					reg = <0x3800 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 64>;
-					marvell,pcie-port = <1>;
-					marvell,pcie-lane = <2>;
-					clocks = <&gateclk 11>;
-					status = "disabled";
-				};
-
-				pcie at 8,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
-					reg = <0x4000 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 65>;
-					marvell,pcie-port = <1>;
-					marvell,pcie-lane = <3>;
-					clocks = <&gateclk 12>;
-					status = "disabled";
-				};
-				pcie at 9,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
-					reg = <0x4800 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 99>;
-					marvell,pcie-port = <2>;
-					marvell,pcie-lane = <0>;
-					clocks = <&gateclk 26>;
-					status = "disabled";
-				};
-
-				pcie at 10,0 {
-					device_type = "pci";
-					assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
-					reg = <0x5000 0 0 0 0>;
-					#address-cells = <3>;
-					#size-cells = <2>;
-					#interrupt-cells = <1>;
-					ranges;
-					interrupt-map-mask = <0 0 0 0>;
-					interrupt-map = <0 0 0 0 &mpic 103>;
-					marvell,pcie-port = <3>;
-					marvell,pcie-lane = <0>;
-					clocks = <&gateclk 27>;
-					status = "disabled";
-				};
-			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
index a895e1b..d2cb11e 100644
--- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
+++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
@@ -56,6 +56,15 @@
 			};
 		};
 
+		pcie-controller {
+			status = "okay";
+			/* Internal mini-PCIe connector */
+			pcie at 1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+		};
+
 		internal-regs {
 			serial at 12000 {
 				clock-frequency = <250000000>;
@@ -169,15 +178,6 @@
 			usb at 51000 {
 				status = "okay";
 			};
-
-			pcie-controller {
-				status = "okay";
-				/* Internal mini-PCIe connector */
-				pcie at 1,0 {
-					/* Port 0, Lane 0 */
-					status = "okay";
-				};
-			};
 		};
 	};
 };
-- 
1.8.1.5




More information about the linux-arm-kernel mailing list