[PATCH v7] tty: serial: add Freescale lpuart driver support
Jingchang Lu
b35083 at freescale.com
Thu Jun 6 21:20:40 EDT 2013
Add Freescale lpuart driver support. The lpuart device
can be found on Vybrid VF610 and Layerscape LS-1 SoCs.
Signed-off-by: Jingchang Lu <b35083 at freescale.com>
---
changes in v7:
Fix build error of "error: implicit declaration of function
"of_alias_get_id" on x86 system.
changes in v6:
Enable being built as a module support.
changes in v5:
Coding style fix, remove redundant code.
Checking clk_prepare_enable return value.
Using devm_ioremap_resource instead of devm_request_and_ioremap.
changes in v4:
Change Vybrid VF610 SoC compatible string to "fsl,vf610-lpuart"
changes in v3:
Use general driver name lpuart instead of mvf for further share between SoCs.
Add bind doc in Documentation/devicetree/bindings/tty/serial.
Remove unused #include header lines and clean up code.
changes in v2:
Remove unused variables and clean up the code.
.../devicetree/bindings/tty/serial/fsl-lpuart.txt | 14 +
drivers/tty/serial/Kconfig | 14 +
drivers/tty/serial/Makefile | 1 +
drivers/tty/serial/fsl_lpuart.c | 874 +++++++++++++++++++++
include/uapi/linux/serial_core.h | 3 +
5 files changed, 906 insertions(+)
create mode 100644 Documentation/devicetree/bindings/tty/serial/fsl-lpuart.txt
create mode 100644 drivers/tty/serial/fsl_lpuart.c
diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-lpuart.txt
new file mode 100644
index 0000000..6fd1dd1
--- /dev/null
+++ b/Documentation/devicetree/bindings/tty/serial/fsl-lpuart.txt
@@ -0,0 +1,14 @@
+* Freescale low power universal asynchronous receiver/transmitter (lpuart)
+
+Required properties:
+- compatible : Should be "fsl,<soc>-lpuart"
+- reg : Address and length of the register set for the device
+- interrupts : Should contain uart interrupt
+
+Example:
+
+uart0: serial at 40027000 {
+ compatible = "fsl,vf610-lpuart";
+ reg = <0x40027000 0x1000>;
+ interrupts = <0 61 0x00>;
+ };
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 7e7006f..8b756a8 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1484,6 +1484,20 @@ config SERIAL_RP2_NR_UARTS
If multiple cards are present, the default limit of 32 ports may
need to be increased.
+config SERIAL_FSL_LPUART
+ tristate "Freescale lpuart serial port support"
+ select SERIAL_CORE
+ help
+ Support for the on-chip lpuart on some Freescale SOCs.
+
+config SERIAL_FSL_LPUART_CONSOLE
+ bool "Console on Freescale lpuart serial port"
+ depends on SERIAL_FSL_LPUART=y
+ select SERIAL_CORE_CONSOLE
+ help
+ If you have enabled the lpuart serial port on the Freescale SoCs,
+ you can make it the console by answering Y to this option.
+
endmenu
endif # TTY
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index eedfec4..cf650f0 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -85,3 +85,4 @@ obj-$(CONFIG_SERIAL_AR933X) += ar933x_uart.o
obj-$(CONFIG_SERIAL_EFM32_UART) += efm32-uart.o
obj-$(CONFIG_SERIAL_ARC) += arc_uart.o
obj-$(CONFIG_SERIAL_RP2) += rp2.o
+obj-$(CONFIG_SERIAL_FSL_LPUART) += fsl_lpuart.o
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
new file mode 100644
index 0000000..263cfaa
--- /dev/null
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -0,0 +1,874 @@
+/*
+ * Freescale lpuart serial port driver
+ *
+ * Copyright 2012-2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#if defined(CONFIG_SERIAL_FSL_LPUART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/console.h>
+#include <linux/serial_core.h>
+#include <linux/tty_flip.h>
+
+/* All registers are 8-bit width */
+#define UARTBDH 0x00
+#define UARTBDL 0x01
+#define UARTCR1 0x02
+#define UARTCR2 0x03
+#define UARTSR1 0x04
+#define UARTCR3 0x06
+#define UARTDR 0x07
+#define UARTCR4 0x0a
+#define UARTCR5 0x0b
+#define UARTMODEM 0x0d
+#define UARTPFIFO 0x10
+#define UARTCFIFO 0x11
+#define UARTSFIFO 0x12
+#define UARTTWFIFO 0x13
+#define UARTTCFIFO 0x14
+#define UARTRWFIFO 0x15
+
+#define UARTBDH_LBKDIE 0x80
+#define UARTBDH_RXEDGIE 0x40
+#define UARTBDH_SBR_MASK 0x1f
+
+#define UARTCR1_LOOPS 0x80
+#define UARTCR1_RSRC 0x20
+#define UARTCR1_M 0x10
+#define UARTCR1_WAKE 0x08
+#define UARTCR1_ILT 0x04
+#define UARTCR1_PE 0x02
+#define UARTCR1_PT 0x01
+
+#define UARTCR2_TIE 0x80
+#define UARTCR2_TCIE 0x40
+#define UARTCR2_RIE 0x20
+#define UARTCR2_ILIE 0x10
+#define UARTCR2_TE 0x08
+#define UARTCR2_RE 0x04
+#define UARTCR2_RWU 0x02
+#define UARTCR2_SBK 0x01
+
+#define UARTSR1_TDRE 0x80
+#define UARTSR1_TC 0x40
+#define UARTSR1_RDRF 0x20
+#define UARTSR1_IDLE 0x10
+#define UARTSR1_OR 0x08
+#define UARTSR1_NF 0x04
+#define UARTSR1_FE 0x02
+#define UARTSR1_PE 0x01
+
+#define UARTCR3_R8 0x80
+#define UARTCR3_T8 0x40
+#define UARTCR3_TXDIR 0x20
+#define UARTCR3_TXINV 0x10
+#define UARTCR3_ORIE 0x08
+#define UARTCR3_NEIE 0x04
+#define UARTCR3_FEIE 0x02
+#define UARTCR3_PEIE 0x01
+
+#define UARTCR4_MAEN1 0x80
+#define UARTCR4_MAEN2 0x40
+#define UARTCR4_M10 0x20
+#define UARTCR4_BRFA_MASK 0x1f
+#define UARTCR4_BRFA_OFF 0
+
+#define UARTCR5_TDMAS 0x80
+#define UARTCR5_RDMAS 0x20
+
+#define UARTMODEM_RXRTSE 0x08
+#define UARTMODEM_TXRTSPOL 0x04
+#define UARTMODEM_TXRTSE 0x02
+#define UARTMODEM_TXCTSE 0x01
+
+#define UARTPFIFO_TXFE 0x80
+#define UARTPFIFO_FIFOSIZE_MASK 0x7
+#define UARTPFIFO_TXSIZE_OFF 4
+#define UARTPFIFO_RXFE 0x08
+#define UARTPFIFO_RXSIZE_OFF 0
+
+#define UARTCFIFO_TXFLUSH 0x80
+#define UARTCFIFO_RXFLUSH 0x40
+#define UARTCFIFO_RXOFE 0x04
+#define UARTCFIFO_TXOFE 0x02
+#define UARTCFIFO_RXUFE 0x01
+
+#define UARTSFIFO_TXEMPT 0x80
+#define UARTSFIFO_RXEMPT 0x40
+#define UARTSFIFO_RXOF 0x04
+#define UARTSFIFO_TXOF 0x02
+#define UARTSFIFO_RXUF 0x01
+
+#define DRIVER_NAME "fsl-lpuart"
+#define DEV_NAME "ttyLP"
+#define UART_NR 6
+
+struct lpuart_port {
+ struct uart_port port;
+ struct clk *clk;
+ unsigned int txfifo_size;
+ unsigned int rxfifo_size;
+};
+
+static struct of_device_id lpuart_dt_ids[] = {
+ {
+ .compatible = "fsl,vf610-lpuart",
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, lpuart_dt_ids);
+
+static void lpuart_stop_tx(struct uart_port *port)
+{
+ unsigned char temp;
+
+ temp = readb(port->membase + UARTCR2);
+ temp &= ~(UARTCR2_TIE | UARTCR2_TCIE);
+ writeb(temp, port->membase + UARTCR2);
+}
+
+static void lpuart_stop_rx(struct uart_port *port)
+{
+ unsigned char temp;
+
+ temp = readb(port->membase + UARTCR2);
+ writeb(temp & ~UARTCR2_RE, port->membase + UARTCR2);
+}
+
+static void lpuart_enable_ms(struct uart_port *port)
+{
+}
+
+static inline void lpuart_transmit_buffer(struct lpuart_port *sport)
+{
+ struct circ_buf *xmit = &sport->port.state->xmit;
+
+ while (!uart_circ_empty(xmit) &&
+ (readb(sport->port.membase + UARTTCFIFO) < sport->txfifo_size)) {
+ writeb(xmit->buf[xmit->tail], sport->port.membase + UARTDR);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ sport->port.icount.tx++;
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&sport->port);
+
+ if (uart_circ_empty(xmit))
+ lpuart_stop_tx(&sport->port);
+}
+
+static void lpuart_start_tx(struct uart_port *port)
+{
+ struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
+ unsigned char temp;
+
+ temp = readb(port->membase + UARTCR2);
+ writeb(temp | UARTCR2_TIE, port->membase + UARTCR2);
+
+ if (readb(port->membase + UARTSR1) & UARTSR1_TDRE)
+ lpuart_transmit_buffer(sport);
+}
+
+static irqreturn_t lpuart_txint(int irq, void *dev_id)
+{
+ struct lpuart_port *sport = dev_id;
+ struct circ_buf *xmit = &sport->port.state->xmit;
+ unsigned long flags;
+
+ spin_lock_irqsave(&sport->port.lock, flags);
+ if (sport->port.x_char) {
+ writeb(sport->port.x_char, sport->port.membase + UARTDR);
+ goto out;
+ }
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) {
+ lpuart_stop_tx(&sport->port);
+ goto out;
+ }
+
+ lpuart_transmit_buffer(sport);
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&sport->port);
+
+out:
+ spin_unlock_irqrestore(&sport->port.lock, flags);
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t lpuart_rxint(int irq, void *dev_id)
+{
+ struct lpuart_port *sport = dev_id;
+ unsigned int flg, ignored = 0;
+ struct tty_port *port = &sport->port.state->port;
+ unsigned long flags;
+ unsigned char rx, sr;
+
+ spin_lock_irqsave(&sport->port.lock, flags);
+
+ while (!(readb(sport->port.membase + UARTSFIFO) & UARTSFIFO_RXEMPT)) {
+ flg = TTY_NORMAL;
+ sport->port.icount.rx++;
+ /*
+ * to clear the FE, OR, NF, FE, PE flags,
+ * read SR1 then read DR
+ */
+ sr = readb(sport->port.membase + UARTSR1);
+ rx = readb(sport->port.membase + UARTDR);
+
+ if (uart_handle_sysrq_char(&sport->port, (unsigned char)rx))
+ continue;
+
+ if (sr & (UARTSR1_PE | UARTSR1_OR | UARTSR1_FE)) {
+ if (sr & UARTSR1_PE)
+ sport->port.icount.parity++;
+ else if (sr & UARTSR1_FE)
+ sport->port.icount.frame++;
+
+ if (sr & UARTSR1_OR)
+ sport->port.icount.overrun++;
+
+ if (sr & sport->port.ignore_status_mask) {
+ if (++ignored > 100)
+ goto out;
+ continue;
+ }
+
+ sr &= sport->port.read_status_mask;
+
+ if (sr & UARTSR1_PE)
+ flg = TTY_PARITY;
+ else if (sr & UARTSR1_FE)
+ flg = TTY_FRAME;
+
+ if (sr & UARTSR1_OR)
+ flg = TTY_OVERRUN;
+
+#ifdef SUPPORT_SYSRQ
+ sport->port.sysrq = 0;
+#endif
+ }
+
+ tty_insert_flip_char(port, rx, flg);
+ }
+
+out:
+ spin_unlock_irqrestore(&sport->port.lock, flags);
+
+ tty_flip_buffer_push(port);
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t lpuart_int(int irq, void *dev_id)
+{
+ struct lpuart_port *sport = dev_id;
+ unsigned char sts;
+
+ sts = readb(sport->port.membase + UARTSR1);
+
+ if (sts & UARTSR1_RDRF)
+ lpuart_rxint(irq, dev_id);
+
+ if (sts & UARTSR1_TDRE &&
+ !(readb(sport->port.membase + UARTCR5) & UARTCR5_TDMAS))
+ lpuart_txint(irq, dev_id);
+
+ return IRQ_HANDLED;
+}
+
+/* return TIOCSER_TEMT when transmitter is not busy */
+static unsigned int lpuart_tx_empty(struct uart_port *port)
+{
+ return (readb(port->membase + UARTSR1) & UARTSR1_TC) ?
+ TIOCSER_TEMT : 0;
+}
+
+static unsigned int lpuart_get_mctrl(struct uart_port *port)
+{
+ unsigned int temp = 0;
+ unsigned char reg;
+
+ reg = readb(port->membase + UARTMODEM);
+ if (reg & UARTMODEM_TXCTSE)
+ temp |= TIOCM_CTS;
+
+ if (reg & UARTMODEM_RXRTSE)
+ temp |= TIOCM_RTS;
+
+ return temp;
+}
+
+static void lpuart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ unsigned char temp;
+
+ temp = readb(port->membase + UARTMODEM) &
+ ~(UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
+
+ if (mctrl & TIOCM_RTS)
+ temp |= UARTMODEM_RXRTSE;
+
+ if (mctrl & TIOCM_CTS)
+ temp |= UARTMODEM_TXCTSE;
+
+ writeb(temp, port->membase + UARTMODEM);
+}
+
+static void lpuart_break_ctl(struct uart_port *port, int break_state)
+{
+ unsigned char temp;
+
+ temp = readb(port->membase + UARTCR2) & ~UARTCR2_SBK;
+
+ if (break_state != 0)
+ temp |= UARTCR2_SBK;
+
+ writeb(temp, port->membase + UARTCR2);
+}
+
+static void lpuart_setup_watermark(struct lpuart_port *sport)
+{
+ unsigned char val, cr2;
+
+ cr2 = readb(sport->port.membase + UARTCR2);
+ cr2 &= ~(UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_TE |
+ UARTCR2_RIE | UARTCR2_RE);
+ writeb(cr2, sport->port.membase + UARTCR2);
+
+ /* determine FIFO size and enable FIFO mode */
+ val = readb(sport->port.membase + UARTPFIFO);
+
+ sport->txfifo_size = 0x1 << (((val >> UARTPFIFO_TXSIZE_OFF) &
+ UARTPFIFO_FIFOSIZE_MASK) + 1);
+
+ sport->rxfifo_size = 0x1 << (((val >> UARTPFIFO_RXSIZE_OFF) &
+ UARTPFIFO_FIFOSIZE_MASK) + 1);
+
+ writeb(val | UARTPFIFO_TXFE | UARTPFIFO_RXFE,
+ sport->port.membase + UARTPFIFO);
+
+ /* flush Tx and Rx FIFO */
+ writeb(UARTCFIFO_TXFLUSH | UARTCFIFO_RXFLUSH,
+ sport->port.membase + UARTCFIFO);
+
+ writeb(2, sport->port.membase + UARTTWFIFO);
+ writeb(1, sport->port.membase + UARTRWFIFO);
+}
+
+static int lpuart_startup(struct uart_port *port)
+{
+ struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
+ int ret;
+ unsigned long flags;
+ unsigned char temp;
+
+ ret = devm_request_irq(port->dev, port->irq, lpuart_int, 0,
+ DRIVER_NAME, sport);
+ if (ret)
+ return ret;
+
+ spin_lock_irqsave(&sport->port.lock, flags);
+
+ lpuart_setup_watermark(sport);
+
+ temp = readb(sport->port.membase + UARTCR2);
+ temp |= (UARTCR2_RIE | UARTCR2_TIE | UARTCR2_RE | UARTCR2_TE);
+ writeb(temp, sport->port.membase + UARTCR2);
+
+ spin_unlock_irqrestore(&sport->port.lock, flags);
+ return 0;
+}
+
+static void lpuart_shutdown(struct uart_port *port)
+{
+ struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
+ unsigned char temp;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ /* disable Rx/Tx and interrupts */
+ temp = readb(port->membase + UARTCR2);
+ temp &= ~(UARTCR2_TE | UARTCR2_RE |
+ UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_RIE);
+ writeb(temp, port->membase + UARTCR2);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ devm_free_irq(port->dev, port->irq, sport);
+}
+
+static void
+lpuart_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
+{
+ struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
+ unsigned long flags;
+ unsigned char cr1, old_cr1, old_cr2, cr4, bdh, modem;
+ unsigned int baud;
+ unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
+ unsigned int sbr, brfa;
+
+ cr1 = old_cr1 = readb(sport->port.membase + UARTCR1);
+ old_cr2 = readb(sport->port.membase + UARTCR2);
+ cr4 = readb(sport->port.membase + UARTCR4);
+ bdh = readb(sport->port.membase + UARTBDH);
+ modem = readb(sport->port.membase + UARTMODEM);
+ /*
+ * only support CS8 and CS7, and for CS7 must enable PE.
+ * supported mode:
+ * - (7,e/o,1)
+ * - (8,n,1)
+ * - (8,m/s,1)
+ * - (8,e/o,1)
+ */
+ while ((termios->c_cflag & CSIZE) != CS8 &&
+ (termios->c_cflag & CSIZE) != CS7) {
+ termios->c_cflag &= ~CSIZE;
+ termios->c_cflag |= old_csize;
+ old_csize = CS8;
+ }
+
+ if ((termios->c_cflag & CSIZE) == CS8 ||
+ (termios->c_cflag & CSIZE) == CS7)
+ cr1 = old_cr1 & ~UARTCR1_M;
+
+ if (termios->c_cflag & CMSPAR) {
+ if ((termios->c_cflag & CSIZE) != CS8) {
+ termios->c_cflag &= ~CSIZE;
+ termios->c_cflag |= CS8;
+ }
+ cr1 |= UARTCR1_M;
+ }
+
+ if (termios->c_cflag & CRTSCTS) {
+ modem |= (UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
+ } else {
+ termios->c_cflag &= ~CRTSCTS;
+ modem &= ~(UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
+ }
+
+ if (termios->c_cflag & CSTOPB)
+ termios->c_cflag &= ~CSTOPB;
+
+ /* parity must be enabled when CS7 to match 8-bits format */
+ if ((termios->c_cflag & CSIZE) == CS7)
+ termios->c_cflag |= PARENB;
+
+ if ((termios->c_cflag & PARENB)) {
+ if (termios->c_cflag & CMSPAR) {
+ cr1 &= ~UARTCR1_PE;
+ cr1 |= UARTCR1_M;
+ } else {
+ cr1 |= UARTCR1_PE;
+ if ((termios->c_cflag & CSIZE) == CS8)
+ cr1 |= UARTCR1_M;
+ if (termios->c_cflag & PARODD)
+ cr1 |= UARTCR1_PT;
+ else
+ cr1 &= ~UARTCR1_PT;
+ }
+ }
+
+ /* ask the core to calculate the divisor */
+ baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 16);
+
+ spin_lock_irqsave(&sport->port.lock, flags);
+
+ sport->port.read_status_mask = 0;
+ if (termios->c_iflag & INPCK)
+ sport->port.read_status_mask |= (UARTSR1_FE | UARTSR1_PE);
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ sport->port.read_status_mask |= UARTSR1_FE;
+
+ /* characters to ignore */
+ sport->port.ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ sport->port.ignore_status_mask |= UARTSR1_PE;
+ if (termios->c_iflag & IGNBRK) {
+ sport->port.ignore_status_mask |= UARTSR1_FE;
+ /*
+ * if we're ignoring parity and break indicators,
+ * ignore overruns too (for real raw support).
+ */
+ if (termios->c_iflag & IGNPAR)
+ sport->port.ignore_status_mask |= UARTSR1_OR;
+ }
+
+ /* update the per-port timeout */
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ /* wait transmit engin complete */
+ while (!(readb(sport->port.membase + UARTSR1) & UARTSR1_TC))
+ barrier();
+
+ /* disable transmit and receive */
+ writeb(old_cr2 & ~(UARTCR2_TE | UARTCR2_RE),
+ sport->port.membase + UARTCR2);
+
+ sbr = sport->port.uartclk / (16 * baud);
+ brfa = ((sport->port.uartclk - (16 * sbr * baud)) * 2) / baud;
+ bdh &= ~UARTBDH_SBR_MASK;
+ bdh |= (sbr >> 8) & 0x1F;
+ cr4 &= ~UARTCR4_BRFA_MASK;
+ brfa &= UARTCR4_BRFA_MASK;
+ writeb(cr4 | brfa, sport->port.membase + UARTCR4);
+ writeb(bdh, sport->port.membase + UARTBDH);
+ writeb(sbr & 0xFF, sport->port.membase + UARTBDL);
+ writeb(cr1, sport->port.membase + UARTCR1);
+ writeb(modem, sport->port.membase + UARTMODEM);
+
+ /* restore control register */
+ writeb(old_cr2, sport->port.membase + UARTCR2);
+
+ spin_unlock_irqrestore(&sport->port.lock, flags);
+}
+
+static const char *lpuart_type(struct uart_port *port)
+{
+ return "FSL_LPUART";
+}
+
+static void lpuart_release_port(struct uart_port *port)
+{
+ /* nothing to do */
+}
+
+static int lpuart_request_port(struct uart_port *port)
+{
+ return 0;
+}
+
+/* configure/autoconfigure the port */
+static void lpuart_config_port(struct uart_port *port, int flags)
+{
+ if (flags & UART_CONFIG_TYPE)
+ port->type = PORT_LPUART;
+}
+
+static int lpuart_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ int ret = 0;
+
+ if (ser->type != PORT_UNKNOWN && ser->type != PORT_LPUART)
+ ret = -EINVAL;
+ if (port->irq != ser->irq)
+ ret = -EINVAL;
+ if (ser->io_type != UPIO_MEM)
+ ret = -EINVAL;
+ if (port->uartclk / 16 != ser->baud_base)
+ ret = -EINVAL;
+ if (port->iobase != ser->port)
+ ret = -EINVAL;
+ if (ser->hub6 != 0)
+ ret = -EINVAL;
+ return ret;
+}
+
+static struct uart_ops lpuart_pops = {
+ .tx_empty = lpuart_tx_empty,
+ .set_mctrl = lpuart_set_mctrl,
+ .get_mctrl = lpuart_get_mctrl,
+ .stop_tx = lpuart_stop_tx,
+ .start_tx = lpuart_start_tx,
+ .stop_rx = lpuart_stop_rx,
+ .enable_ms = lpuart_enable_ms,
+ .break_ctl = lpuart_break_ctl,
+ .startup = lpuart_startup,
+ .shutdown = lpuart_shutdown,
+ .set_termios = lpuart_set_termios,
+ .type = lpuart_type,
+ .request_port = lpuart_request_port,
+ .release_port = lpuart_release_port,
+ .config_port = lpuart_config_port,
+ .verify_port = lpuart_verify_port,
+};
+
+static struct lpuart_port *lpuart_ports[UART_NR];
+
+#ifdef CONFIG_SERIAL_FSL_LPUART_CONSOLE
+static void lpuart_console_putchar(struct uart_port *port, int ch)
+{
+ while (!(readb(port->membase + UARTSR1) & UARTSR1_TDRE))
+ barrier();
+
+ writeb(ch, port->membase + UARTDR);
+}
+
+static void
+lpuart_console_write(struct console *co, const char *s, unsigned int count)
+{
+ struct lpuart_port *sport = lpuart_ports[co->index];
+ unsigned char old_cr2, cr2;
+
+ /* first save CR2 and then disable interrupts */
+ cr2 = old_cr2 = readb(sport->port.membase + UARTCR2);
+ cr2 |= (UARTCR2_TE | UARTCR2_RE);
+ cr2 &= ~(UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_RIE);
+ writeb(cr2, sport->port.membase + UARTCR2);
+
+ uart_console_write(&sport->port, s, count, lpuart_console_putchar);
+
+ /* wait for transmitter finish complete and restore CR2 */
+ while (!(readb(sport->port.membase + UARTSR1) & UARTSR1_TC))
+ barrier();
+
+ writeb(old_cr2, sport->port.membase + UARTCR2);
+}
+
+/*
+ * if the port was already initialised (eg, by a boot loader),
+ * try to determine the current setup.
+ */
+static void __init
+lpuart_console_get_options(struct lpuart_port *sport, int *baud,
+ int *parity, int *bits)
+{
+ unsigned char cr, bdh, bdl, brfa;
+ unsigned int sbr, uartclk, baud_raw;
+
+ cr = readb(sport->port.membase + UARTCR2);
+ cr &= UARTCR2_TE | UARTCR2_RE;
+ if (!cr)
+ return;
+
+ /* ok, the port was enabled */
+
+ cr = readb(sport->port.membase + UARTCR1);
+
+ *parity = 'n';
+ if (cr & UARTCR1_PE) {
+ if (cr & UARTCR1_PT)
+ *parity = 'o';
+ else
+ *parity = 'e';
+ }
+
+ if (cr & UARTCR1_M)
+ *bits = 9;
+ else
+ *bits = 8;
+
+ bdh = readb(sport->port.membase + UARTBDH);
+ bdh &= UARTBDH_SBR_MASK;
+ bdl = readb(sport->port.membase + UARTBDL);
+ sbr = bdh;
+ sbr <<= 8;
+ sbr |= bdl;
+ brfa = readb(sport->port.membase + UARTCR4);
+ brfa &= UARTCR4_BRFA_MASK;
+
+ uartclk = clk_get_rate(sport->clk);
+ /*
+ * baud = mod_clk/(16*(sbr[13]+(brfa)/32)
+ */
+ baud_raw = uartclk / (16 * (sbr + brfa / 32));
+
+ if (*baud != baud_raw)
+ printk(KERN_INFO "Serial: Console lpuart rounded baud rate"
+ "from %d to %d\n", baud_raw, *baud);
+}
+
+static int __init lpuart_console_setup(struct console *co, char *options)
+{
+ struct lpuart_port *sport;
+ int baud = 115200;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ /*
+ * check whether an invalid uart number has been specified, and
+ * if so, search for the first available port that does have
+ * console support.
+ */
+ if (co->index == -1 || co->index >= ARRAY_SIZE(lpuart_ports))
+ co->index = 0;
+
+ sport = lpuart_ports[co->index];
+ if (sport == NULL)
+ return -ENODEV;
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+ else
+ lpuart_console_get_options(sport, &baud, &parity, &bits);
+
+ lpuart_setup_watermark(sport);
+
+ return uart_set_options(&sport->port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver lpuart_reg;
+static struct console lpuart_console = {
+ .name = DEV_NAME,
+ .write = lpuart_console_write,
+ .device = uart_console_device,
+ .setup = lpuart_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &lpuart_reg,
+};
+
+#define LPUART_CONSOLE (&lpuart_console)
+#else
+#define LPUART_CONSOLE NULL
+#endif
+
+static struct uart_driver lpuart_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = DRIVER_NAME,
+ .dev_name = DEV_NAME,
+ .nr = ARRAY_SIZE(lpuart_ports),
+ .cons = LPUART_CONSOLE,
+};
+
+static int lpuart_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct lpuart_port *sport;
+ struct resource *res;
+ int ret;
+
+ sport = devm_kzalloc(&pdev->dev, sizeof(*sport), GFP_KERNEL);
+ if (!sport)
+ return -ENOMEM;
+
+ pdev->dev.coherent_dma_mask = 0;
+
+ ret = of_alias_get_id(np, "serial");
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
+ return ret;
+ }
+ sport->port.line = ret;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res)
+ return -ENODEV;
+
+ sport->port.mapbase = res->start;
+ sport->port.membase = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(sport->port.membase))
+ return PTR_ERR(sport->port.membase);
+
+ sport->port.dev = &pdev->dev;
+ sport->port.type = PORT_LPUART;
+ sport->port.iotype = UPIO_MEM;
+ sport->port.irq = platform_get_irq(pdev, 0);
+ sport->port.ops = &lpuart_pops;
+ sport->port.flags = UPF_BOOT_AUTOCONF;
+
+ sport->clk = devm_clk_get(&pdev->dev, "ipg");
+ if (IS_ERR(sport->clk)) {
+ ret = PTR_ERR(sport->clk);
+ dev_err(&pdev->dev, "failed to get uart clk: %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(sport->clk);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to enable uart clk: %d\n", ret);
+ return ret;
+ }
+
+ sport->port.uartclk = clk_get_rate(sport->clk);
+
+ lpuart_ports[sport->port.line] = sport;
+
+ platform_set_drvdata(pdev, &sport->port);
+
+ ret = uart_add_one_port(&lpuart_reg, &sport->port);
+ if (ret) {
+ clk_disable_unprepare(sport->clk);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int lpuart_remove(struct platform_device *pdev)
+{
+ struct lpuart_port *sport = platform_get_drvdata(pdev);
+
+ uart_remove_one_port(&lpuart_reg, &sport->port);
+
+ clk_disable_unprepare(sport->clk);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int lpuart_suspend(struct device *dev)
+{
+ struct lpuart_port *sport = dev_get_drvdata(dev);
+
+ uart_suspend_port(&lpuart_reg, &sport->port);
+
+ return 0;
+}
+
+static int lpuart_resume(struct device *dev)
+{
+ struct lpuart_port *sport = dev_get_drvdata(dev);
+
+ uart_resume_port(&lpuart_reg, &sport->port);
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(lpuart_pm_ops, lpuart_suspend, lpuart_resume);
+
+static struct platform_driver lpuart_driver = {
+ .probe = lpuart_probe,
+ .remove = lpuart_remove,
+ .driver = {
+ .name = "fsl-lpuart",
+ .owner = THIS_MODULE,
+ .of_match_table = lpuart_dt_ids,
+ .pm = &lpuart_pm_ops,
+ },
+};
+
+static int __init lpuart_serial_init(void)
+{
+ int ret;
+
+ pr_info("serial: Freescale lpuart driver\n");
+
+ ret = uart_register_driver(&lpuart_reg);
+ if (ret)
+ return ret;
+
+ ret = platform_driver_register(&lpuart_driver);
+ if (ret)
+ uart_unregister_driver(&lpuart_reg);
+
+ return 0;
+}
+
+static void __exit lpuart_serial_exit(void)
+{
+ platform_driver_unregister(&lpuart_driver);
+ uart_unregister_driver(&lpuart_reg);
+}
+
+module_init(lpuart_serial_init);
+module_exit(lpuart_serial_exit);
+
+MODULE_DESCRIPTION("Freescale lpuart serial port driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
index 74c2bf7..c8eaeb5 100644
--- a/include/uapi/linux/serial_core.h
+++ b/include/uapi/linux/serial_core.h
@@ -226,4 +226,7 @@
/* Rocketport EXPRESS/INFINITY */
#define PORT_RP2 102
+/* Freescale lpuart */
+#define PORT_LPUART 103
+
#endif /* _UAPILINUX_SERIAL_CORE_H */
--
1.8.0
More information about the linux-arm-kernel
mailing list