[RESEND PATCH 1/3] ARM: EXYNOS: Move arm core power down clock to exynos5250 common clock

[Amit Daniel Kachhap]

Now with common clock support added for exynos5250 it is necessary to move
this code to exynos5250 common clock driver as clock registers should be
handled there. This change is tested in exynos5250 based arndale platform.

Cc: Abhilash Kesavan <a.kesavan at samsung.com>
Cc: Thomas Abraham <thomas.abraham at linaro.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel at samsung.com>
---
Re-based against linux for-next branch.
 
 arch/arm/mach-exynos/cpuidle.c       |   35 ----------------------------
 drivers/clk/samsung/clk-exynos5250.c |   42 ++++++++++++++++++++++++++++++++++
 2 files changed, 42 insertions(+), 35 deletions(-)

diff --git a/arch/arm/mach-exynos/cpuidle.c b/arch/arm/mach-exynos/cpuidle.c
index 17a18ff..4667907 100644
--- a/arch/arm/mach-exynos/cpuidle.c
+++ b/arch/arm/mach-exynos/cpuidle.c
@@ -159,46 +159,11 @@ static int exynos4_enter_lowpower(struct cpuidle_device *dev,
 		return exynos4_enter_core0_aftr(dev, drv, new_index);
 }
 
-static void __init exynos5_core_down_clk(void)
-{
-	unsigned int tmp;
-
-	/*
-	 * Enable arm clock down (in idle) and set arm divider
-	 * ratios in WFI/WFE state.
-	 */
-	tmp = PWR_CTRL1_CORE2_DOWN_RATIO | \
-	      PWR_CTRL1_CORE1_DOWN_RATIO | \
-	      PWR_CTRL1_DIV2_DOWN_EN	 | \
-	      PWR_CTRL1_DIV1_DOWN_EN	 | \
-	      PWR_CTRL1_USE_CORE1_WFE	 | \
-	      PWR_CTRL1_USE_CORE0_WFE	 | \
-	      PWR_CTRL1_USE_CORE1_WFI	 | \
-	      PWR_CTRL1_USE_CORE0_WFI;
-	__raw_writel(tmp, EXYNOS5_PWR_CTRL1);
-
-	/*
-	 * Enable arm clock up (on exiting idle). Set arm divider
-	 * ratios when not in idle along with the standby duration
-	 * ratios.
-	 */
-	tmp = PWR_CTRL2_DIV2_UP_EN	 | \
-	      PWR_CTRL2_DIV1_UP_EN	 | \
-	      PWR_CTRL2_DUR_STANDBY2_VAL | \
-	      PWR_CTRL2_DUR_STANDBY1_VAL | \
-	      PWR_CTRL2_CORE2_UP_RATIO	 | \
-	      PWR_CTRL2_CORE1_UP_RATIO;
-	__raw_writel(tmp, EXYNOS5_PWR_CTRL2);
-}
-
 static int __init exynos4_init_cpuidle(void)
 {
 	int cpu_id, ret;
 	struct cpuidle_device *device;
 
-	if (soc_is_exynos5250())
-		exynos5_core_down_clk();
-
 	ret = cpuidle_register_driver(&exynos4_idle_driver);
 	if (ret) {
 		printk(KERN_ERR "CPUidle failed to register driver\n");
diff --git a/drivers/clk/samsung/clk-exynos5250.c b/drivers/clk/samsung/clk-exynos5250.c
index 5c97e75..89f51e9 100644
--- a/drivers/clk/samsung/clk-exynos5250.c
+++ b/drivers/clk/samsung/clk-exynos5250.c
@@ -21,6 +21,8 @@
 
 #define SRC_CPU			0x200
 #define DIV_CPU0		0x500
+#define PWR_CTRL1		0x1020
+#define PWR_CTRL2		0x1024
 #define SRC_CORE1		0x4204
 #define SRC_TOP0		0x10210
 #define SRC_TOP2		0x10218
@@ -63,6 +65,23 @@
 #define PLL_DIV2_SEL		0x20a24
 #define GATE_IP_DISP1		0x10928
 
+/*Below definitions are used for PWR_CTRL settings*/
+#define PWR_CTRL1_CORE2_DOWN_RATIO		(7 << 28)
+#define PWR_CTRL1_CORE1_DOWN_RATIO		(7 << 16)
+#define PWR_CTRL1_DIV2_DOWN_EN			(1 << 9)
+#define PWR_CTRL1_DIV1_DOWN_EN			(1 << 8)
+#define PWR_CTRL1_USE_CORE1_WFE			(1 << 5)
+#define PWR_CTRL1_USE_CORE0_WFE			(1 << 4)
+#define PWR_CTRL1_USE_CORE1_WFI			(1 << 1)
+#define PWR_CTRL1_USE_CORE0_WFI			(1 << 0)
+
+#define PWR_CTRL2_DIV2_UP_EN			(1 << 25)
+#define PWR_CTRL2_DIV1_UP_EN			(1 << 24)
+#define PWR_CTRL2_DUR_STANDBY2_VAL		(1 << 16)
+#define PWR_CTRL2_DUR_STANDBY1_VAL		(1 << 8)
+#define PWR_CTRL2_CORE2_UP_RATIO		(1 << 4)
+#define PWR_CTRL2_CORE1_UP_RATIO		(1 << 0)
+
 /*
  * Let each supported clock get a unique id. This id is used to lookup the clock
  * for device tree based platforms. The clocks are categorized into three
@@ -110,6 +129,8 @@ enum exynos5250_clks {
 static __initdata unsigned long exynos5250_clk_regs[] = {
 	SRC_CPU,
 	DIV_CPU0,
+	PWR_CTRL1,
+	PWR_CTRL2,
 	SRC_CORE1,
 	SRC_TOP0,
 	SRC_TOP2,
@@ -474,6 +495,7 @@ void __init exynos5250_clk_init(struct device_node *np)
 {
 	void __iomem *reg_base;
 	struct clk *apll, *mpll, *epll, *vpll, *bpll, *gpll, *cpll;
+	unsigned int tmp;
 
 	if (np) {
 		reg_base = of_iomap(np, 0);
@@ -516,6 +538,26 @@ void __init exynos5250_clk_init(struct device_node *np)
 	samsung_clk_register_gate(exynos5250_gate_clks,
 			ARRAY_SIZE(exynos5250_gate_clks));
 
+	/*
+	 * Enable arm clock down (in idle) and set arm divider
+	 * ratios in WFI/WFE state.
+	 */
+	tmp = (PWR_CTRL1_CORE2_DOWN_RATIO | PWR_CTRL1_CORE1_DOWN_RATIO |
+		PWR_CTRL1_DIV2_DOWN_EN | PWR_CTRL1_DIV1_DOWN_EN |
+		PWR_CTRL1_USE_CORE1_WFE | PWR_CTRL1_USE_CORE0_WFE |
+		PWR_CTRL1_USE_CORE1_WFI | PWR_CTRL1_USE_CORE0_WFI);
+	__raw_writel(tmp, reg_base + PWR_CTRL1);
+
+	/*
+	 * Enable arm clock up (on exiting idle). Set arm divider
+	 * ratios when not in idle along with the standby duration
+	 * ratios.
+	 */
+	tmp = (PWR_CTRL2_DIV2_UP_EN | PWR_CTRL2_DIV1_UP_EN |
+		PWR_CTRL2_DUR_STANDBY2_VAL | PWR_CTRL2_DUR_STANDBY1_VAL |
+		PWR_CTRL2_CORE2_UP_RATIO | PWR_CTRL2_CORE1_UP_RATIO);
+	__raw_writel(tmp, reg_base + PWR_CTRL2);
+
 	pr_info("Exynos5250: clock setup completed, armclk=%ld\n",
 			_get_rate("armclk"));
 }
-- 
1.7.1