[PATCH 2/4] ARM: dts: omap5-uevm: Add USB Host support

[Sricharan R]

Hi Roger,

On Wednesday 05 June 2013 04:02 PM, Roger Quadros wrote:
> Hi Sricharan,
>
> Thanks for sending this, but some parts are outdated. See below.
>
> On 06/05/2013 09:46 AM, Sricharan R wrote:
>> From: Roger Quadros <rogerq at ti.com>
>>
>> Provide the RESET regulators for the USB PHYs, the USB Host
>> port modes and the PHY devices.
>>
>> Also provide pin multiplexer information for the USB host
>> pins.
>>
>> Cc: Roger Quadros <rogerq at ti.com>
>> Signed-off-by: Roger Quadros <rogerq at ti.com>
>> [Sricharan R <r.sricharan at ti.com>: Replaced constants with preprocessor macros]
>> Signed-off-by: Sricharan R <r.sricharan at ti.com>
>> ---
>>  arch/arm/boot/dts/omap5-uevm.dts |   77 ++++++++++++++++++++++++++++++++++++++
>>  arch/arm/boot/dts/omap5.dtsi     |   30 +++++++++++++++
>>  2 files changed, 107 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
>> index 843a001..cf862df 100644
>> --- a/arch/arm/boot/dts/omap5-uevm.dts
>> +++ b/arch/arm/boot/dts/omap5-uevm.dts
>> @@ -25,6 +25,47 @@
>>  		regulator-max-microvolt = <3000000>;
>>  	};
>>  
>> +	/* HS USB Port 2 RESET */
>> +	hsusb2_reset: hsusb2_reset_reg {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "hsusb2_reset";
>> +		regulator-min-microvolt = <3300000>;
>> +		regulator-max-microvolt = <3300000>;
>> +		gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 HUB_NRESET */
>> +		startup-delay-us = <70000>;
>> +		enable-active-high;
>> +	};
>> +
>> +	/* HS USB Host PHY on PORT 2 */
>> +	hsusb2_phy: hsusb2_phy {
>> +		compatible = "usb-nop-xceiv";
>> +		reset-supply = <&hsusb2_reset>;
>> +	};
>> +
>> +	/* HS USB Port 3 RESET */
>> +	hsusb3_reset: hsusb3_reset_reg {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "hsusb3_reset";
>> +		regulator-min-microvolt = <3300000>;
>> +		regulator-max-microvolt = <3300000>;
>> +		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>; /* gpio3_79 ETH_NRESET */
>> +		startup-delay-us = <70000>;
>> +		enable-active-high;
>> +	};
>> +
>> +	/* HS USB Host PHY on PORT 3 */
>> +	hsusb3_phy: hsusb3_phy {
>> +		compatible = "usb-nop-xceiv";
>> +		reset-supply = <&hsusb3_reset>;
>> +	};
>> +
>> +	/* hsusb2_phy is clocked by FREF_CLK1 i.e. auxclk1 */
>> +	clock_alias {
>> +		clock-name = "auxclk1_ck";
>> +		clock-alias = "main_clk";
>> +		device = <&hsusb2_phy>;
>> +		clock-frequency = <19200000>; /* 19.2 MHz */
>> +	};
> clock_alias node is not required. Instead we need to rely on proper clock binding
> and provide reference to the clock phandle in the PHY node.
>
> as an example please see here
> https://lkml.org/lkml/2013/4/19/124
>
> However this clock binding technique is still under discussion/transition.
> https://patchwork.kernel.org/patch/2541331/
>
> So, I suggest you leave the auxclk1 part out for now and we can get it in later once
> the clock binding stuff is sorted out. The side effect of this is that PORT 2 (i.e. USB Hub)
> will not work. USB Ethernet should still work IMO.
  Ok will drop that part then.

Thanks,
 Sricharan