[PATCH 11/11] i2c: omap: enhance pinctrl support

Hebbar, Gururaja gururaja.hebbar at ti.com
Wed Jun 5 05:05:37 EDT 2013


On Fri, May 31, 2013 at 23:04:59, Kevin Hilman wrote:
> Hebbar Gururaja <gururaja.hebbar at ti.com> writes:
> 
> > Amend the I2C omap pin controller to optionally take a pin control
> > handle and set the state of the pins to:
> >
> > - "default" on boot, resume and before performing an i2c transfer
> > - "idle" after initial default, after resume default, and after each
> > i2c xfer
> > - "sleep" on suspend()
> >
> > By optionally putting the pins into sleep state in the suspend callback
> > we can accomplish two things.
> > - One is to minimize current leakage from pins and thus save power,
> > - second, we can prevent the IP from driving pins output in an
> > uncontrolled manner, which may happen if the power domain drops the
> > domain regulator.
> >
> > Note:
> > A .suspend & .resume callback is added which simply puts the pins to sleep
> > state upon suspend & are moved to default & idle state upon resume.
> >
> > If any of the above pin states are missing in dt, a warning message
> > about the missing state is displayed.
> > If certain pin-states are not available, to remove this warning message
> > pass respective state name with null phandler.
> >
> > (Changes based on i2c-nomadik.c)
> >
> > Signed-off-by: Hebbar Gururaja <gururaja.hebbar at ti.com>
> > Cc: Tony Lindgren <tony at atomide.com>
> > Cc: Wolfram Sang <wsa at the-dreams.de>
> > Cc: linux-omap at vger.kernel.org
> > Cc: linux-i2c at vger.kernel.org
> 
> [...]
> 
> > @@ -664,7 +673,13 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
> >  
> >  out:
> >  	pm_runtime_mark_last_busy(dev->dev);
> > +
> >  	pm_runtime_put_autosuspend(dev->dev);
> > +	/* Optionally let pins go into idle state */
> > +	if (!IS_ERR(dev->pins_idle))
> > +		if (pinctrl_select_state(dev->pinctrl, dev->pins_idle))
> > +			dev_err(dev->dev, "could not set pins to idle state\n");
> 
> This is wrong.  You're changing the muxing before the device actually
> goes idle.  Anything you want to happen when the device actually idles
> for real has to be in runtime PM callbacks.
> 
> Looking below, I see it's already in the callbacks, so why is it here also?

Just to be double sure. Seems it is unwanted.

> 
> [...]
> 
> > @@ -1300,6 +1348,10 @@ static int omap_i2c_runtime_suspend(struct device *dev)
> >  		omap_i2c_read_reg(_dev, OMAP_I2C_STAT_REG);
> >  	}
> >  
> > +	if (!IS_ERR(_dev->pins_idle))
> > +		if (pinctrl_select_state(_dev->pinctrl, _dev->pins_idle))
> > +			dev_err(dev, "could not set pins to idle state\n");
> > +
> >  	return 0;
> >  }
> >  
> 
> Kevin
> 


Regards, 
Gururaja



More information about the linux-arm-kernel mailing list