[PATCHv4 22/33] CLK: OMAP: update gate clock setup for OMAP3

[Tero Kristo]

On 07/30/2013 11:13 PM, Nishanth Menon wrote:
> On 07/23/2013 02:20 AM, Tero Kristo wrote:
>> OMAP3 gate clocks are handled through the clk driver now. Basic gate
>> clock can't be used as the OMAP3 gate clocks have some special features,
>> namely the idle status linkage which is on separate register.
>>
>> Signed-off-by: Tero Kristo <t-kristo at ti.com>
>> ---
>>   drivers/clk/omap/gate.c |   27 +++++++++++++++++++++++++--
>>   1 file changed, 25 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/clk/omap/gate.c b/drivers/clk/omap/gate.c
>> index 7186bb2..b560ff4 100644
>> --- a/drivers/clk/omap/gate.c
>> +++ b/drivers/clk/omap/gate.c
>> @@ -28,12 +28,19 @@
>>
>>   #ifdef CONFIG_OF
>>
>> -static const struct clk_ops omap_gate_clk_ops = {
>> +static const struct clk_ops omap_gate_clkdm_clk_ops = {
>>       .init        = &omap2_init_clk_clkdm,
>>       .enable        = &omap2_clkops_enable_clkdm,
>>       .disable    = &omap2_clkops_disable_clkdm,
>>   };
>>
>> +static const struct clk_ops omap_gate_clk_ops = {
>> +    .init        = &omap2_init_clk_clkdm,
>> +    .enable        = &omap2_dflt_clk_enable,
>> +    .disable    = &omap2_dflt_clk_disable,
>> +    .is_enabled    = &omap2_dflt_clk_is_enabled,
>> +};
>> +
>>   void __init of_omap_gate_clk_setup(struct device_node *node)
>>   {
>>       struct clk *clk;
>> @@ -43,6 +50,7 @@ void __init of_omap_gate_clk_setup(struct
>> device_node *node)
>>       int num_parents;
>>       const char **parent_names;
>>       int i;
>> +    u32 val;
>>
>>       clk_hw = kzalloc(sizeof(struct clk_hw_omap), GFP_KERNEL);
>>       if (!clk_hw) {
>> @@ -56,7 +64,22 @@ void __init of_omap_gate_clk_setup(struct
>> device_node *node)
>>       of_property_read_string(node, "ti,clkdm-name",
>> &clk_hw->clkdm_name);
>>
>>       init.name = clk_name;
>> -    init.ops = &omap_gate_clk_ops;
>> +    init.flags = 0;
>> +
>> +    if (of_property_read_u32_index(node, "reg", 0, &val)) {
>> +        /* No register, clkdm control only */
>> +        init.ops = &omap_gate_clkdm_clk_ops;
>> +    } else {
>> +        init.ops = &omap_gate_clk_ops;
>> +        clk_hw->enable_reg = of_iomap(node, 0);
>> +        of_property_read_u32(node, "ti,enable-bit", &val);
>> +        clk_hw->enable_bit = val;
>> +
>> +        if (of_property_read_bool(node, "ti,dss-clk"))
>> +            clk_hw->ops = &clkhwops_omap3430es2_dss_usbhost_wait;
>
> umm, it was going relatively ok so far, till i hit this :( it is
> probably a quirk... but still..

Some of the clocks need special hwops for them to work properly it 
seems... It looks nasty yea but the best I could think of.

>
>> +        else
>> +            clk_hw->ops = &clkhwops_wait;
>> +    }
>>
>>       num_parents = of_clk_get_parent_count(node);
>>       if (num_parents < 1) {
>>
>
> but still no usage of "ti,omap-gate-clock" makes me question the need
> for this file.
>

Yea, no ti,omap-gate-clock, but there is ti,gate-clock. Just look harder.