[PATCH v2 8/8] ARM: DRA7: dts: Add the dts files for dra7 SoC and dra7-evm board
Nishanth Menon
nm at ti.com
Tue Jul 30 08:30:24 EDT 2013
On 07/30/2013 06:25 AM, Rajendra Nayak wrote:
> From: R Sricharan <r.sricharan at ti.com>
>
> Add minimal device tree source needed for DRA7 based SoCs.
> Also add a board dts file for the dra7-evm (based on dra752)
> which contains 1.5G of memory with 1G interleaved and 512MB
> non-interleaved. Also added in the board file are pin configuration
> details for i2c, mcspi and uart devices on board.
>
> Signed-off-by: R Sricharan <r.sricharan at ti.com>
> Signed-off-by: Rajendra Nayak <rnayak at ti.com>
> Signed-off-by: Sourav Poddar <sourav.poddar at ti.com>
> ---
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/dra7-evm.dts | 163 ++++++++++++++
> arch/arm/boot/dts/dra7.dtsi | 488 ++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 653 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/dra7-evm.dts
> create mode 100644 arch/arm/boot/dts/dra7.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 641b3c9..e2f8566 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -173,7 +173,8 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
> am335x-bone.dtb \
> am3517-evm.dtb \
> am3517_mt_ventoux.dtb \
> - am43x-epos-evm.dtb
> + am43x-epos-evm.dtb \
> + dra7-evm.dtb
> dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
> dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
> dtb-$(CONFIG_ARCH_U8500) += snowball.dtb \
> diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
> new file mode 100644
> index 0000000..7b0b563
> --- /dev/null
> +++ b/arch/arm/boot/dts/dra7-evm.dts
> @@ -0,0 +1,163 @@
> +/*
> + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +/dts-v1/;
> +
> +/include/ "dra7.dtsi"
> +
> +/ {
> + model = "TI DRA7";
> + compatible = "ti,dra7-evm", "ti,dra7";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x80000000 0x60000000>; /* 1536 MB */
> + };
> +};
> +
> +&dra7_pmx_core {
> + i2c1_pins: pinmux_i2c1_pins {
> + pinctrl-single,pins = <
> + 0x400 0x60000 /* i2c1_sda */
> + 0x404 0x60000 /* i2c1_scl */
> + >;
> + };
> +
> + i2c2_pins: pinmux_i2c2_pins {
> + pinctrl-single,pins = <
> + 0x408 0x60000 /* i2c2_sda */
> + 0x40c 0x60000 /* i2c2_scl */
> + >;
> + };
> +
> + i2c3_pins: pinmux_i2c3_pins {
> + pinctrl-single,pins = <
> + 0x410 0x60000 /* i2c3_sda */
> + 0x414 0x60000 /* i2c3_scl */
> + >;
> + };
> +
> + mcspi1_pins: pinmux_mcspi1_pins {
> + pinctrl-single,pins = <
> + 0x3a4 0x40000 /* spi2_clk */
> + 0x3a8 0x40000 /* spi2_d1 */
> + 0x3ac 0x40000 /* spi2_d0 */
> + 0x3b0 0xc0000 /* spi2_cs0 */
> + 0x3b4 0xc0000 /* spi2_cs1 */
> + 0x3b8 0xe0006 /* spi2_cs2 */
> + 0x3bc 0xe0006 /* spi2_cs3 */
> + >;
> + };
> +
> + mcspi2_pins: pinmux_mcspi2_pins {
> + pinctrl-single,pins = <
> + 0x3c0 0x40000 /* spi2_sclk */
> + 0x3c4 0xc0000 /* spi2_d1 */
> + 0x3c8 0xc0000 /* spi2_d1 */
> + 0x3cc 0xe0000 /* spi2_cs0 */
> + >;
> + };
> +
> + uart1_pins: pinmux_uart1_pins {
> + pinctrl-single,pins = <
> + 0x3e0 0xe0000 /* uart1_rxd */
> + 0x3e4 0xe0000 /* uart1_txd */
> + 0x3e8 0x60003 /* uart1_ctsn */
> + 0x3ec 0x60003 /* uart1_rtsn */
> + >;
> + };
> +
> + uart2_pins: pinmux_uart2_pins {
> + pinctrl-single,pins = <
> + 0x3f0 0x60000 /* uart2_rxd */
> + 0x3f4 0x60000 /* uart2_txd */
> + 0x3f8 0x60000 /* uart2_ctsn */
> + 0x3fc 0x60000 /* uart2_rtsn */
> + >;
> + };
> +
> + uart3_pins: pinmux_uart3_pins {
> + pinctrl-single,pins = <
> + 0x248 0xc0000 /* uart3_rxd */
> + 0x24c 0xc0000 /* uart3_txd */
> + >;
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> +
> + clock-frequency = <400000>;
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins>;
> +
> + clock-frequency = <400000>;
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c3_pins>;
> +
> + clock-frequency = <3400000>;
> +};
> +
> +&i2c4 {
> + status = "disabled";
> +};
> +
> +&i2c5 {
> + status = "disabled";
> +};
> +
> +&mcspi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcspi1_pins>;
> +};
> +
> +&mcspi2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcspi2_pins>;
> +};
> +
> +&mcspi3 {
> + status = "disabled";
> +};
> +
> +&mcspi4 {
> + status = "disabled";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_pins>;
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart2_pins>;
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart3_pins>;
> +};
> +
> +&uart4 {
> + status = "disabled";
> +};
> +
> +&uart5 {
> + status = "disabled";
> +};
> +
> +&uart6 {
> + status = "disabled";
> +};
> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
> new file mode 100644
> index 0000000..8a0c08e
> --- /dev/null
> +++ b/arch/arm/boot/dts/dra7.dtsi
> @@ -0,0 +1,488 @@
> +/*
> + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + * Based on "omap4.dtsi"
> + */
> +
> +/include/ "skeleton.dtsi"
> +
> +/ {
> + compatible = "ti,dra7xx";
> + interrupt-parent = <&gic>;
> +
> + aliases {
> + serial0 = &uart1;
> + serial1 = &uart2;
> + serial2 = &uart3;
> + serial3 = &uart4;
> + serial4 = &uart5;
> + serial5 = &uart6;
> + };
> +
> + cpus {
> + cpu at 0 {
> + compatible = "arm,cortex-a15";
> + timer {
> + compatible = "arm,armv7-timer";
> + /*
> + * PPI secure/nonsecure IRQ,
> + * active low level-sensitive
> + */
> + interrupts = <1 13 0x308>,
> + <1 14 0x308>;
> + clock-frequency = <6144000>;
> + };
> + };
> + cpu at 1 {
> + compatible = "arm,cortex-a15";
> + timer {
> + compatible = "arm,armv7-timer";
> + /*
> + * PPI secure/nonsecure IRQ,
> + * active low level-sensitive
> + */
> + interrupts = <1 13 0x308>,
> + <1 14 0x308>;
> + clock-frequency = <6144000>;
> + };
> + };
> + };
> +
> + gic: interrupt-controller at 48211000 {
> + compatible = "arm,cortex-a15-gic";
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + reg = <0x48211000 0x1000>,
> + <0x48212000 0x1000>;
> + };
> +
> + /*
> + * The soc node represents the soc top level view. It is uses for IPs
> + * that are not memory mapped in the MPU view or for the MPU itself.
> + */
> + soc {
> + compatible = "ti,omap-infra";
> + mpu {
> + compatible = "ti,omap5-mpu";
> + ti,hwmods = "mpu";
> + };
> + };
> +
> + /*
> + * XXX: Use a flat representation of the SOC interconnect.
> + * The real OMAP interconnect network is quite complex.
> + * Since that will not bring real advantage to represent that in DT for
> + * the moment, just use a fake OCP bus entry to represent the whole bus
> + * hierarchy.
> + */
> + ocp {
> + compatible = "ti,omap4-l3-noc", "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + ti,hwmods = "l3_main_1", "l3_main_2";
> +
> + counter32k: counter at 4ae04000 {
> + compatible = "ti,omap-counter32k";
> + reg = <0x4ae04000 0x40>;
> + ti,hwmods = "counter_32k";
> + };
> +
> + dra7_pmx_core: pinmux at 4a003400 {
> + compatible = "pinctrl-single";
> + reg = <0x4a003400 0x0464>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-single,register-width = <32>;
> + pinctrl-single,function-mask = <0x3fffffff>;
> + };
> +
> + sdma: dma-controller at 4a056000 {
> + compatible = "ti,omap4430-sdma";
> + reg = <0x4a056000 0x1000>;
> + interrupts = <0 12 0x4>,
> + <0 13 0x4>,
> + <0 14 0x4>,
> + <0 15 0x4>;
> + #dma-cells = <1>;
> + #dma-channels = <32>;
> + #dma-requests = <127>;
> + };
> +
> + gpio1: gpio at 4ae10000 {
> + compatible = "ti,omap4-gpio";
> + reg = <0x4ae10000 0x200>;
> + interrupts = <0 29 0x4>;
> + ti,hwmods = "gpio1";
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + };
> +
> + gpio2: gpio at 48055000 {
> + compatible = "ti,omap4-gpio";
> + reg = <0x48055000 0x200>;
> + interrupts = <0 30 0x4>;
> + ti,hwmods = "gpio2";
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + };
> +
> + gpio3: gpio at 48057000 {
> + compatible = "ti,omap4-gpio";
> + reg = <0x48057000 0x200>;
> + interrupts = <0 31 0x4>;
> + ti,hwmods = "gpio3";
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + };
> +
> + gpio4: gpio at 48059000 {
> + compatible = "ti,omap4-gpio";
> + reg = <0x48059000 0x200>;
> + interrupts = <0 32 0x4>;
> + ti,hwmods = "gpio4";
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + };
> +
> + gpio5: gpio at 4805b000 {
> + compatible = "ti,omap4-gpio";
> + reg = <0x4805b000 0x200>;
> + interrupts = <0 33 0x4>;
> + ti,hwmods = "gpio5";
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + };
> +
> + gpio6: gpio at 4805d000 {
> + compatible = "ti,omap4-gpio";
> + reg = <0x4805d000 0x200>;
> + interrupts = <0 34 0x4>;
> + ti,hwmods = "gpio6";
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + };
> +
> + gpio7: gpio at 48051000 {
> + compatible = "ti,omap4-gpio";
> + reg = <0x48051000 0x200>;
> + interrupts = <0 35 0x4>;
> + ti,hwmods = "gpio7";
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + };
> +
> + gpio8: gpio at 48053000 {
> + compatible = "ti,omap4-gpio";
> + reg = <0x48053000 0x200>;
> + interrupts = <0 121 0x4>;
> + ti,hwmods = "gpio8";
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + };
> +
> + uart1: serial at 4806a000 {
> + compatible = "ti,omap4-uart";
> + reg = <0x4806a000 0x100>;
> + interrupts = <0 72 0x4>;
> + ti,hwmods = "uart1";
> + clock-frequency = <48000000>;
> + };
> +
> + uart2: serial at 4806c000 {
> + compatible = "ti,omap4-uart";
> + reg = <0x4806c000 0x100>;
> + interrupts = <0 73 0x4>;
> + ti,hwmods = "uart2";
> + clock-frequency = <48000000>;
> + };
> +
> + uart3: serial at 48020000 {
> + compatible = "ti,omap4-uart";
> + reg = <0x48020000 0x100>;
> + interrupts = <0 74 0x4>;
> + ti,hwmods = "uart3";
> + clock-frequency = <48000000>;
> + };
> +
> + uart4: serial at 4806e000 {
> + compatible = "ti,omap4-uart";
> + reg = <0x4806e000 0x100>;
> + interrupts = <0 70 0x4>;
> + ti,hwmods = "uart4";
> + clock-frequency = <48000000>;
> + };
> +
> + uart5: serial at 48066000 {
> + compatible = "ti,omap4-uart";
> + reg = <0x48066000 0x100>;
> + interrupts = <0 105 0x4>;
> + ti,hwmods = "uart5";
> + clock-frequency = <48000000>;
> + };
> +
> + uart6: serial at 48068000 {
> + compatible = "ti,omap4-uart";
> + reg = <0x48068000 0x100>;
> + interrupts = <0 106 0x4>;
> + ti,hwmods = "uart6";
> + clock-frequency = <48000000>;
> + };
> +
> + timer1: timer at 4ae18000 {
> + compatible = "ti,omap5430-timer";
> + reg = <0x4ae18000 0x80>;
> + interrupts = <0 37 0x4>;
> + ti,hwmods = "timer1";
> + ti,timer-alwon;
> + };
> +
> + timer2: timer at 48032000 {
> + compatible = "ti,omap5430-timer";
> + reg = <0x48032000 0x80>;
> + interrupts = <0 38 0x4>;
> + ti,hwmods = "timer2";
> + };
> +
> + timer3: timer at 48034000 {
> + compatible = "ti,omap5430-timer";
> + reg = <0x48034000 0x80>;
> + interrupts = <0 39 0x4>;
> + ti,hwmods = "timer3";
> + };
> +
> + timer4: timer at 48036000 {
> + compatible = "ti,omap5430-timer";
> + reg = <0x48036000 0x80>;
> + interrupts = <0 40 0x4>;
> + ti,hwmods = "timer4";
> + };
> +
> + timer5: timer at 48820000 {
> + compatible = "ti,omap5430-timer";
> + reg = <0x48820000 0x80>;
> + interrupts = <0 41 0x4>;
> + ti,hwmods = "timer5";
> + ti,timer-dsp;
> + };
> +
> + timer6: timer at 48822000 {
> + compatible = "ti,omap5430-timer";
> + reg = <0x48822000 0x80>;
> + interrupts = <0 42 0x4>;
> + ti,hwmods = "timer6";
> + ti,timer-dsp;
> + ti,timer-pwm;
> + };
> +
> + timer7: timer at 48824000 {
> + compatible = "ti,omap5430-timer";
> + reg = <0x48824000 0x80>;
> + interrupts = <0 43 0x4>;
> + ti,hwmods = "timer7";
> + ti,timer-dsp;
> + };
> +
> + timer8: timer at 48826000 {
> + compatible = "ti,omap5430-timer";
> + reg = <0x48826000 0x80>;
> + interrupts = <0 44 0x4>;
> + ti,hwmods = "timer8";
> + ti,timer-dsp;
> + ti,timer-pwm;
> + };
> +
> + timer9: timer at 4803e000 {
> + compatible = "ti,omap5430-timer";
> + reg = <0x4803e000 0x80>;
> + interrupts = <0 45 0x4>;
> + ti,hwmods = "timer9";
> + };
> +
> + timer10: timer at 48086000 {
> + compatible = "ti,omap5430-timer";
> + reg = <0x48086000 0x80>;
> + interrupts = <0 46 0x4>;
> + ti,hwmods = "timer10";
> + };
> +
> + timer11: timer at 48088000 {
> + compatible = "ti,omap5430-timer";
> + reg = <0x48088000 0x80>;
> + interrupts = <0 47 0x4>;
> + ti,hwmods = "timer11";
> + ti,timer-pwm;
> + };
> +
> + wdt2: wdt at 4ae14000 {
> + compatible = "ti,omap4-wdt";
> + reg = <0x4ae14000 0x80>;
> + interrupts = <0 80 0x4>;
> + ti,hwmods = "wd_timer2";
> + };
> +
> + i2c1: i2c at 48070000 {
> + compatible = "ti,omap4-i2c";
> + reg = <0x48070000 0x100>;
> + interrupts = <0 56 0x4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + ti,hwmods = "i2c1";
> + };
> +
> + i2c2: i2c at 48072000 {
> + compatible = "ti,omap4-i2c";
> + reg = <0x48072000 0x100>;
> + interrupts = <0 57 0x4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + ti,hwmods = "i2c2";
> + };
> +
> + i2c3: i2c at 48060000 {
> + compatible = "ti,omap4-i2c";
> + reg = <0x48060000 0x100>;
> + interrupts = <0 61 0x4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + ti,hwmods = "i2c3";
> + };
> +
> + i2c4: i2c at 4807a000 {
> + compatible = "ti,omap4-i2c";
> + reg = <0x4807a000 0x100>;
> + interrupts = <0 62 0x4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + ti,hwmods = "i2c4";
> + };
> +
> + i2c5: i2c at 4807c000 {
> + compatible = "ti,omap4-i2c";
> + reg = <0x4807c000 0x100>;
> + interrupts = <0 60 0x4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + ti,hwmods = "i2c5";
> + };
> +
> + mmc1: mmc at 4809c000 {
> + compatible = "ti,omap4-hsmmc";
> + reg = <0x4809c000 0x400>;
> + interrupts = <0 83 0x4>;
> + ti,hwmods = "mmc1";
> + ti,dual-volt;
> + ti,needs-special-reset;
> + dmas = <&sdma 61>, <&sdma 62>;
> + dma-names = "tx", "rx";
> + };
> +
> + mmc2: mmc at 480b4000 {
> + compatible = "ti,omap4-hsmmc";
> + reg = <0x480b4000 0x400>;
> + interrupts = <0 86 0x4>;
> + ti,hwmods = "mmc2";
> + ti,needs-special-reset;
> + dmas = <&sdma 47>, <&sdma 48>;
> + dma-names = "tx", "rx";
> + };
> +
> + mmc3: mmc at 480ad000 {
> + compatible = "ti,omap4-hsmmc";
> + reg = <0x480ad000 0x400>;
> + interrupts = <0 94 0x4>;
> + ti,hwmods = "mmc3";
> + ti,needs-special-reset;
> + dmas = <&sdma 77>, <&sdma 78>;
> + dma-names = "tx", "rx";
> + };
> +
> + mmc4: mmc at 480d1000 {
> + compatible = "ti,omap4-hsmmc";
> + reg = <0x480d1000 0x400>;
> + interrupts = <0 96 0x4>;
> + ti,hwmods = "mmc4";
> + ti,needs-special-reset;
> + dmas = <&sdma 57>, <&sdma 58>;
> + dma-names = "tx", "rx";
> + };
> +
> + mcspi1: spi at 48098000 {
> + compatible = "ti,omap4-mcspi";
> + reg = <0x48098000 0x200>;
> + interrupts = <0 65 0x4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + ti,hwmods = "mcspi1";
> + ti,spi-num-cs = <4>;
> + dmas = <&sdma 35>,
> + <&sdma 36>,
> + <&sdma 37>,
> + <&sdma 38>,
> + <&sdma 39>,
> + <&sdma 40>,
> + <&sdma 41>,
> + <&sdma 42>;
> + dma-names = "tx0", "rx0", "tx1", "rx1",
> + "tx2", "rx2", "tx3", "rx3";
> + };
> +
> + mcspi2: spi at 4809a000 {
> + compatible = "ti,omap4-mcspi";
> + reg = <0x4809a000 0x200>;
> + interrupts = <0 66 0x4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + ti,hwmods = "mcspi2";
> + ti,spi-num-cs = <2>;
> + dmas = <&sdma 43>,
> + <&sdma 44>,
> + <&sdma 45>,
> + <&sdma 46>;
> + dma-names = "tx0", "rx0", "tx1", "rx1";
> + };
> +
> + mcspi3: spi at 480b8000 {
> + compatible = "ti,omap4-mcspi";
> + reg = <0x480b8000 0x200>;
> + interrupts = <0 91 0x4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + ti,hwmods = "mcspi3";
> + ti,spi-num-cs = <2>;
> + dmas = <&sdma 15>, <&sdma 16>;
> + dma-names = "tx0", "rx0";
> + };
> +
> + mcspi4: spi at 480ba000 {
> + compatible = "ti,omap4-mcspi";
> + reg = <0x480ba000 0x200>;
> + interrupts = <0 48 0x4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + ti,hwmods = "mcspi4";
> + ti,spi-num-cs = <1>;
> + dmas = <&sdma 70>, <&sdma 71>;
> + dma-names = "tx0", "rx0";
> + };
> + };
> +};
>
ref: [1], we discussed that we should now be able to introduce all
instances of h/w blocks into the dra7.dts. Further, considering [2]
would you not want to follow "status = disabled" for all modules by
default and enable required modules in board file, so that we dont have
to respin this yet again?
[1] http://marc.info/?t=137416599400001&r=1&w=2
[2] http://marc.info/?l=linux-omap&m=137510358229479&w=2
--
Regards,
Nishanth Menon
More information about the linux-arm-kernel
mailing list