[PATCH 1/3] misc: Add crossbar driver

Nishanth Menon nm at ti.com
Thu Jul 18 14:56:15 EDT 2013


On 07/18/2013 11:43 AM, Sricharan R wrote:
> Some socs have a large number of interrupts/dma requests to service
> the needs of its many peripherals and subsystems. All of the
> requests lines from the subsystems are not needed at the same
> time, so they have to be muxed to the controllers appropriately.
> In such places a interrupt/dma controllers are preceded by an
> IRQ/DMA CROSSBAR that provides flexibility in muxing the device
> requests to the controller inputs.
>
> The Peripheral irq/dma requests are connected to one crossbar's input
> and the output of the crossbar is connected to controller's input
> line. On POR, there are some mappings which are done by default.
> Those peripherals which do not have a mapping on POR, should be configured
> to route its requests using the crossbar.
>
> The drivers identifies every controller's crossbar as individual devices.
> The mappings can be specified from the DT crossbar nodes and those gets mapped
> during the crossbar device's probe. The mappings can also be specified by adding
> the crossbar lines to the peripheral device nodes and map it with
> crossbar_map/unmap apis.
>
> Signed-off-by: Sricharan R <r.sricharan at ti.com>
> ---
>   .../devicetree/bindings/arm/omap/crossbar.txt      |   24 ++
>   drivers/misc/Kconfig                               |    8 +
>   drivers/misc/Makefile                              |    1 +
>   drivers/misc/crossbar.c                            |  258 ++++++++++++++++++++
>   include/linux/crossbar.h                           |   71 ++++++
>   5 files changed, 362 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/arm/omap/crossbar.txt
>   create mode 100644 drivers/misc/crossbar.c
>   create mode 100644 include/linux/crossbar.h
>
> diff --git a/Documentation/devicetree/bindings/arm/omap/crossbar.txt b/Documentation/devicetree/bindings/arm/omap/crossbar.txt
> new file mode 100644
> index 0000000..02a8a28
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/omap/crossbar.txt
> @@ -0,0 +1,24 @@
> +* TI - IRQ/DMA Crossbar
> +
> +This version is an implementation of the Crossbar IRQ/DMA IP
> +
> +Required properties:
> +- compatible : Should be "ti,dra-crossbar"
> +- crossbar-name: Name of the controller to which crossbar output is routed
> +- reg:	Contains crossbar register address range
> +- reg-width: Represents the width of the individual registers
> +- crossbar-lines:  Default mappings.Should contain the crossbar-name
> +		   device name, int/dma request number, crossbar number,
> +		   register offset in the same order.
> +
> +Examples:
> +		crossbar_mpu: mpuirq at 4a002a48 {
> +			compatible = "crossbar";
> +			crossbar-name = "mpu-irq";
> +			reg = <0x4a002a48 0x0130>;
> +			reg-width = <16>;
> +			crossbar-lines = "mpu-irq", "rtc-ss-alarm", <0x9f 0xd9 0x12c>,
> +					 "mpu-irq", "mcasp3-arevt", <0x9e 0x96 0x12a>,
> +					 "mpu-irq", "mcasp3-axevt", <0x9d 0x97 0x128>;
> +		};

I carry forward my TI internal objection to this approach:

NAK.

DRA7 uses a cross bar to map a line to GIC interrupt. Flow of interrupt 
is as follows:
hardware IP block -interrupt line-> IRQ Cross bar -> GIC IRQ line --> 
MPU IRQ.


What we have done today for DRA is to provide IRQ numbers as direct maps 
from hardware IP block to GIC based on default IRQ cross bar mapping.

Lets see what happens as a result of this:

https://patchwork.kernel.org/patch/2825148/ (introducing DTS for DRA7)
uart1 to uart6 is defined. while in fact 10 uarts exist on IP block.
uart1: serial at 4806a000 {
<snip>
+			interrupts = <0 72 0x4>;
Assumes that GIC interrupt by default mapping used.

Now, think of a product that wants to use UART10 instead of UART1, SoC 
design allows you do that by doing a remapping of GIC interrupt to 
UART10 - which is awesome.

Option 1: u-boot/bootloader
mw.l IRQ_CROSSBAR_address with value to map uart10 to GIC IRQ for UART1,

Option 2: in kernel do a raw_writel version of option 1.
This patch does option 1 in kernel in a "fancy way" - why the heck would 
I want to do that when u-boot allows me to do the same thing in uEnv.txt

Option 3: map GIC interrupt to IRQ CROSS bar dynamically.
a) Allows us to define every single IP available on DRA7 SoC.
b) GIC allocation happens dynamically
c) allow products use IPs as needed.

Sorry, Conceptually option 3 is the right approach in my view.
instead of doing
uart1: serial at 4806a000 {
<snip>
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;

we should be able to do the following:
uart1: serial at 4806a000 {
<snip>
+			interrupts = <TI_IRQ_CROSSBAR 192 IRQ_TYPE_LEVEL_HIGH>;

and not worry about the GIC interrupt number used


-- 
Regards,
Nishanth Menon



More information about the linux-arm-kernel mailing list