[PATCH] ARM: tegra: cpuidle: use CPUIDLE_FLAG_TIMER_STOP flag

[Stephen Warren]

On 07/17/2013 03:45 PM, Daniel Lezcano wrote:
> On 07/17/2013 10:31 PM, Stephen Warren wrote:
>> On 07/17/2013 04:15 AM, Joseph Lo wrote:
>>> On Wed, 2013-07-17 at 03:51 +0800, Stephen Warren wrote:
>>>> On 07/16/2013 05:17 AM, Joseph Lo wrote:
>>>>> On Tue, 2013-07-16 at 02:04 +0800, Stephen Warren wrote:
>>>>>> On 06/25/2013 03:23 AM, Joseph Lo wrote:
>>>>>>> Use the CPUIDLE_FLAG_TIMER_STOP and let the cpuidle framework
>>>>>>> to handle the CLOCK_EVT_NOTIFY_BROADCAST_ENTER/EXIT when entering
>>>>>>> this state.
>> ... [ discussion of issues with Joesph's patches applied]
>>>
>>> OK. I did more stress tests last night and today. I found it cause by
>>> the patch "ARM: tegra: cpuidle: use CPUIDLE_FLAG_TIMER_STOP flag" and
>>> only impact the Tegra20 platform. The hot plug regression seems due to
>>> this patch. After dropping this patch on top of v3.11-rc1, the Tegra20
>>> can back to normal.
>>>
>>> And the hop plug and suspend stress test can pass on Tegra30/114 too.
>>>
>>> Can the other two patch series for Tegra114 to support CPU idle power
>>> down mode and system suspend still moving forward, not be blocked by
>>> this patch?
>>>
>>> Looks the CPUIDLE_FLAG_TIMER_STOP flag still cause some other issue for
>>> hot plug on Tegra20, I will continue to check this. You can just drop
>>> this patch.
>>
>> OK, if I drop that patch, then everything on Tegra20 and Tegra30 seems
>> fine again.
>>
>> However, I've found some new and exciting issue on Tegra114!
>>
>> With unmodified v3.11-rc1, I can do the following without issue:
>>
>> * Unplug/replug CPUs, so that I had all combinations of CPU 1, 2, 3
>> plugged/unpplugged (with CPU 0 always plugged).
>>
>> * Unplug/replug CPUs, so that I had all combinations of CPU 0, 1, 2, 3
>> plugged/unpplugged (with the obvious exception of never having all CPUs
>> unplugged).
>>
>> However, if I try this with your Tegra114 cpuidle and suspend patches
>> applied, I see the following issues:
>>
>> 1) If I boot, unplug CPU 0, then replug CPU 0, the system immediately
>> hard-hangs.
>>
>> 2) If I run the hotplug test script, leaving CPU 0 always present, I
>> sometimes see:
>>
>>> root at localhost:~# for i in `seq 1 50`; do echo ITERATION $i; ./cpuonline.py; done
>>> ITERATION 1
>>> echo 0 > /sys/devices/system/cpu/cpu2/online
>>> [  458.910054] CPU2: shutdown
>>> echo 0 > /sys/devices/system/cpu/cpu1/online
>>> [  461.004371] CPU1: shutdown
>>> echo 0 > /sys/devices/system/cpu/cpu3/online
>>> [  463.027341] CPU3: shutdown
>>> echo 1 > /sys/devices/system/cpu/cpu1/online
>>> [  465.061412] CPU1: Booted secondary processor
>>> echo 1 > /sys/devices/system/cpu/cpu2/online
>>> [  467.095313] CPU2: Booted secondary processor
>>> [  467.113243] ------------[ cut here ]------------
>>> [  467.117948] WARNING: CPU: 2 PID: 0 at kernel/time/tick-broadcast.c:667 tick_broadcast_oneshot_control+0x19c/0x1c4()
>>> [  467.128352] Modules linked in:
>>> [  467.131455] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 3.11.0-rc1-00022-g7487363-dirty #49
>>> [  467.139678] [<c0015620>] (unwind_backtrace+0x0/0xf8) from [<c001154c>] (show_stack+0x10/0x14)
>>> [  467.148228] [<c001154c>] (show_stack+0x10/0x14) from [<c05135a8>] (dump_stack+0x80/0xc4)
>>> [  467.156336] [<c05135a8>] (dump_stack+0x80/0xc4) from [<c0024590>] (warn_slowpath_common+0x64/0x88)
>>> [  467.165300] [<c0024590>] (warn_slowpath_common+0x64/0x88) from [<c00245d0>] (warn_slowpath_null+0x1c/0x24)
>>> [  467.174959] [<c00245d0>] (warn_slowpath_null+0x1c/0x24) from [<c00695e4>] (tick_broadcast_oneshot_control+0x19c/0x1c4)
>>> [  467.185659] [<c00695e4>] (tick_broadcast_oneshot_control+0x19c/0x1c4) from [<c0067cdc>] (clockevents_notify+0x1b0/0x1dc)
>>> [  467.196538] [<c0067cdc>] (clockevents_notify+0x1b0/0x1dc) from [<c034f348>] (cpuidle_idle_call+0x11c/0x168)
>>> [  467.206292] [<c034f348>] (cpuidle_idle_call+0x11c/0x168) from [<c000f134>] (arch_cpu_idle+0x8/0x38)
>>> [  467.215359] [<c000f134>] (arch_cpu_idle+0x8/0x38) from [<c0061038>] (cpu_startup_entry+0x60/0x134)
>>> [  467.224325] [<c0061038>] (cpu_startup_entry+0x60/0x134) from [<800083d8>] (0x800083d8)
>>> [  467.232227] ---[ end trace ea579be22a00e7fb ]---
>>> echo 0 > /sys/devices/system/cpu/cpu1/online
>>> [  469.126682] CPU1: shutdown
>>
>> I have found no solution for (1) (although I didn't look hard!).
>>
>> (2) can be solved with the following (at least 50 iterations of my test
>> script worked with this patch applied):
> 
> Actually this warning is resulting from a bug in the tick broadcast code
> and has been solved with commit:
> 
> https://git.kernel.org/cgit/linux/kernel/git/tip/tip.git/commit/?h=timers/urgent&id=ea8deb8dfa6b0e8d1b3d1051585706739b46656c
> 
> This patch has been merged in timers/urgent branch but still need to
> merged with timers/core.
> 
> The patch below does not fix the warning but prevents the tick warning
> to occur. Applying the patch above will fix your problem.

Yes, I was imprecise when I said solve; I simply meant that making that
change prevented me from seeing that issue any more.

That patch is already in v3.11-rc1, and I was using that as a base when
I applied Joseph's patches. So, it doesn't solve this issue.