[PATCH v12 06/13] usb: chipidea: add otg_cap attribute for otg capable

[Peter Chen]

On Fri, Jul 12, 2013 at 12:42:10PM +0300, Alexander Shishkin wrote:
> Peter Chen <peter.chen at freescale.com> writes:
> 
> > On Fri, Jul 12, 2013 at 11:12:01AM +0300, Alexander Shishkin wrote:
> >> Peter Chen <peter.chen at freescale.com> writes:
> >> 
> >> > Since we need otgsc to know vbus's status at some chipidea
> >> > controllers even it is peripheral-only mode. Besides, some
> >> > SoCs (eg, AR9331 SoC) don't have otgsc register even
> >> > the DCCPARAMS_DC and DCCPARAMS_HC are both 1 at CAP_DCCPARAMS.
> >> > We inroduce otg_cap attribute to indicate if the controller
> >> > is otg capable, defaultly, we follow the rule that if DCCPARAMS_DC
> >> > and DCCPARAMS_HC are both 1 at CAP_DCCPARAMS are otg capable, but if there
> >> > is exception, the platform can override it by device tree or platform data.
> >> >
> >> > Signed-off-by: Peter Chen <peter.chen at freescale.com>
> >> > ---
> >> 
> >> [...]
> >> 
> >> > diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h
> >> > index 118bf66..0a906b4 100644
> >> > --- a/include/linux/usb/chipidea.h
> >> > +++ b/include/linux/usb/chipidea.h
> >> > @@ -7,6 +7,12 @@
> >> >  
> >> >  #include <linux/usb/otg.h>
> >> >  
> >> > +enum usb_otg_cap {
> >> > +	OTG_CAP_ATTR_IS_NOT_EXISTED = 0,
> >> > +	OTG_CAP_ATTR_IS_TRUE,
> >> > +	OTG_CAP_ATTR_IS_FALSE,
> >> > +};
> >> 
> >> We don't really need all three, do we? We only need to know if the
> >> controller *can't* do otg. The rest we can infer from dr_mode and
> >> DCCPARAMS. So it can be another bit in flags rather than a separate
> >> field in platdata.
> >> 
> >
> > In order to cover below two cases, I have no other idea.
> >
> > 1. For mips Soc (ARxxx), if dr_mode = otg and it is 1 for both
> > mode at DCCPARAMS,  It can switch role through proc or whatever,
> > but NO otgsc register, it is NOT otg-capable.
> 
> For this case, platform should set
> 
> platdata->flags &= CI_HDRC_NO_OTG
> 
> , which will set ci->is_otg = false. No ci->is_otg => no touching
> OTGSC.
> 
> > 2. For peripheral-only case at most chipidea controllers,
> > the dr_mode = peripheral and it is 1 for both modes at DCCPARAMS,
> > the otgsc can be visited, it is otg-capable.
> 
> Then platform *doesn't* set CI_HDRC_NO_OTG and ci->is_otg is set to
> true, because DCCPARAMS.DC==1 and DCCPARAMS.HC==1, but we only have one
> role initialized, because of dr_mode==peripheral, so no role switching
> happens, but OTGSC accesses are fine.
> 
> Makes sense?
> 

Agree, I will add the define of CI_HDRC_NO_OTG to
struct ci_hdrc_platform_data, and add below comments

/* Only set it when DCCPARAMS.DC==1 and DCCPARAMS.HC==1,
 * but otg is not supported (no register otgsc).
 */

-- 

Best Regards,
Peter Chen