[RFC PATCH] pwm: atmel-pwm: add pwm controller driver
Bo Shen
voice.shen at atmel.com
Thu Jul 4 03:27:57 EDT 2013
Hi All,
On 6/21/2013 16:45, Bo Shen wrote:
> add atmel pwm controller driver based on PWM framework
>
> this is basic function implementation of pwm controller
> it can work with pwm based led and backlight
>
> Signed-off-by: Bo Shen <voice.shen at atmel.com>
> ---
> .../devicetree/bindings/pwm/atmel-pwm.txt | 19 ++
> drivers/pwm/Kconfig | 9 +
> drivers/pwm/Makefile | 1 +
> drivers/pwm/pwm-atmel.c | 326 ++++++++++++++++++++
> 4 files changed, 355 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pwm/atmel-pwm.txt
> create mode 100644 drivers/pwm/pwm-atmel.c
Does this patch can be applied? If yes, I will send out the formal patch
without RFC in subject. If no, please help review this patch and give
your comments.
Thanks.
Best Regards,
Bo Shen
> diff --git a/Documentation/devicetree/bindings/pwm/atmel-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt
> new file mode 100644
> index 0000000..127fcdb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt
> @@ -0,0 +1,19 @@
> +Atmel PWM controller
> +
> +Required properties:
> + - compatible: should be one of:
> + - "atmel,at91sam9rl-pwm"
> + - "atmel,sama5-pwm"
> + - reg: physical base address and length of the controller's registers
> + - #pwm-cells: Should be 3.
> + - The first cell specifies the per-chip index of the PWM to use
> + - The second cell is the period in nanoseconds
> + - The third cell is used to encode the polarity of PWM output
> +
> +Example:
> +
> + pwm0: pwm at f8034000 {
> + compatible = "atmel,at91sam9rl-pwm";
> + reg = <0xf8034000 0x400>;
> + #pwm-cells = <3>;
> + };
> diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
> index 115b644..70518c9 100644
> --- a/drivers/pwm/Kconfig
> +++ b/drivers/pwm/Kconfig
> @@ -37,6 +37,15 @@ config PWM_AB8500
> To compile this driver as a module, choose M here: the module
> will be called pwm-ab8500.
>
> +config PWM_ATMEL
> + tristate "Atmel PWM support"
> + depends on ARCH_AT91
> + help
> + Generic PWM framework driver for Atmel SoC.
> +
> + To compile this driver as a module, choose M here: the module
> + will be called pwm-atmel.
> +
> config PWM_ATMEL_TCB
> tristate "Atmel TC Block PWM support"
> depends on ATMEL_TCLIB && OF
> diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
> index 94ba21e..a905a52 100644
> --- a/drivers/pwm/Makefile
> +++ b/drivers/pwm/Makefile
> @@ -1,5 +1,6 @@
> obj-$(CONFIG_PWM) += core.o
> obj-$(CONFIG_PWM_AB8500) += pwm-ab8500.o
> +obj-$(CONFIG_PWM_ATMEL) += pwm-atmel.o
> obj-$(CONFIG_PWM_ATMEL_TCB) += pwm-atmel-tcb.o
> obj-$(CONFIG_PWM_BFIN) += pwm-bfin.o
> obj-$(CONFIG_PWM_IMX) += pwm-imx.o
> diff --git a/drivers/pwm/pwm-atmel.c b/drivers/pwm/pwm-atmel.c
> new file mode 100644
> index 0000000..15ec4d5
> --- /dev/null
> +++ b/drivers/pwm/pwm-atmel.c
> @@ -0,0 +1,326 @@
> +/*
> + * Driver for Atmel Pulse Width Modulation Controller
> + *
> + * Copyright (C) 2013 Atmel Semiconductor Technology Ltd.
> + *
> + * GPL v2 or later
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/pinctrl/consumer.h>
> +#include <linux/platform_device.h>
> +#include <linux/pwm.h>
> +#include <linux/slab.h>
> +
> +#define PWM_MR 0x00
> +#define PWM_ENA 0x04
> +#define PWM_DIS 0x08
> +#define PWM_SR 0x0C
> +
> +#define PWM_CMR 0x00
> +
> +/* The following register for PWM v1 */
> +#define PWMv1_CDTY 0x04
> +#define PWMv1_CPRD 0x08
> +#define PWMv1_CUPD 0x10
> +
> +/* The following register for PWM v2 */
> +#define PWMv2_CDTY 0x04
> +#define PWMv2_CDTYUPD 0x08
> +#define PWMv2_CPRD 0x0C
> +#define PWMv2_CPRDUPD 0x10
> +
> +#define PWM_NUM 4
> +
> +struct atmel_pwm_chip {
> + struct pwm_chip chip;
> + struct clk *clk;
> + void __iomem *base;
> +
> + void (*config)(struct atmel_pwm_chip *chip, struct pwm_device *pwm,
> + unsigned int dty, unsigned int prd);
> +};
> +
> +#define to_atmel_pwm_chip(chip) container_of(chip, struct atmel_pwm_chip, chip)
> +
> +static inline u32 atmel_pwm_readl(struct atmel_pwm_chip *chip, int offset)
> +{
> + return readl(chip->base + offset);
> +}
> +
> +static inline void atmel_pwm_writel(struct atmel_pwm_chip *chip, int offset,
> + u32 val)
> +{
> + writel(val, chip->base + offset);
> +}
> +
> +static inline u32 atmel_pwm_ch_readl(struct atmel_pwm_chip *chip, int ch,
> + int offset)
> +{
> + return readl(chip->base + 0x200 + ch * 0x20 + offset);
> +}
> +
> +static inline void atmel_pwm_ch_writel(struct atmel_pwm_chip *chip, int ch,
> + int offset, u32 val)
> +{
> + writel(val, chip->base + 0x200 + ch * 0x20 + offset);
> +}
> +
> +static int atmel_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
> + int duty_ns, int period_ns)
> +{
> + struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip);
> + unsigned long long val, prd, dty;
> + unsigned long long div, clk_rate;
> + int ret, pres = 0;
> +
> + clk_rate = clk_get_rate(atmel_pwm->clk);
> +
> + while (1) {
> + div = 1000000000;
> + div *= 1 << pres;
> + val = clk_rate * period_ns;
> + prd = div_u64(val, div);
> + val = clk_rate * duty_ns;
> + dty = div_u64(val, div);
> +
> + if (prd < 0x0001 || dty < 0x0)
> + return -EINVAL;
> +
> + if (prd > 0xffff || dty > 0xffff) {
> + if (++pres > 0x10)
> + return -EINVAL;
> + continue;
> + }
> +
> + break;
> + }
> +
> + /* Enable clock */
> + ret = clk_prepare_enable(atmel_pwm->clk);
> + if (ret) {
> + pr_err("failed to enable pwm clock\n");
> + return ret;
> + }
> +
> + atmel_pwm->config(atmel_pwm, pwm, dty, prd);
> +
> + /* Check whether need to disable clock */
> + val = atmel_pwm_readl(atmel_pwm, PWM_SR);
> + if ((val & 0xf) == 0)
> + clk_disable_unprepare(atmel_pwm->clk);
> +
> + return 0;
> +}
> +
> +static void atmel_pwm_config_v1(struct atmel_pwm_chip *atmel_pwm,
> + struct pwm_device *pwm, unsigned int dty, unsigned int prd)
> +{
> + unsigned int val;
> +
> + /*
> + * if the pwm channel is enabled, using update register to update
> + * related register value, or else write it directly
> + */
> + if (test_bit(PWMF_ENABLED, &pwm->flags)) {
> + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv1_CUPD, dty);
> +
> + val = atmel_pwm_ch_readl(atmel_pwm, pwm->hwpwm, PWM_CMR);
> + val &= ~(1 << 10);
> + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWM_CMR, val);
> + } else {
> + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv1_CDTY, dty);
> + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv1_CPRD, prd);
> + }
> +}
> +
> +static void atmel_pwm_config_v2(struct atmel_pwm_chip *atmel_pwm,
> + struct pwm_device *pwm, unsigned int dty, unsigned int prd)
> +{
> + /*
> + * if the pwm channel is enabled, using update register to update
> + * related register value, or else write it directly
> + */
> + if (test_bit(PWMF_ENABLED, &pwm->flags)) {
> + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv2_CDTYUPD, dty);
> + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv2_CPRDUPD, prd);
> + } else {
> + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv2_CDTY, dty);
> + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv2_CPRD, prd);
> + }
> +}
> +
> +static int atmel_pwm_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm,
> + enum pwm_polarity polarity)
> +{
> + struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip);
> + u32 val = 0;
> + int ret;
> +
> + /* Enable clock */
> + ret = clk_prepare_enable(atmel_pwm->clk);
> + if (ret) {
> + pr_err("failed to enable pwm clock\n");
> + return ret;
> + }
> +
> + if (polarity == PWM_POLARITY_NORMAL)
> + val &= ~(1 << 9);
> + else
> + val |= 1 << 9;
> +
> + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWM_CMR, val);
> +
> + /* Disable clock */
> + clk_disable_unprepare(atmel_pwm->clk);
> +
> + return 0;
> +}
> +
> +static int atmel_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
> +{
> + struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip);
> +
> + clk_prepare_enable(atmel_pwm->clk);
> +
> + atmel_pwm_writel(atmel_pwm, PWM_ENA, 1 << pwm->hwpwm);
> +
> + return 0;
> +}
> +
> +static void atmel_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
> +{
> + struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip);
> + u32 val;
> +
> + atmel_pwm_writel(atmel_pwm, PWM_DIS, 1 << pwm->hwpwm);
> +
> + /* Disable clock */
> + val = atmel_pwm_readl(atmel_pwm, PWM_SR);
> + if ((val & 0xf) == 0)
> + clk_disable_unprepare(atmel_pwm->clk);
> +}
> +
> +static const struct pwm_ops atmel_pwm_ops = {
> + .config = atmel_pwm_config,
> + .set_polarity = atmel_pwm_set_polarity,
> + .enable = atmel_pwm_enable,
> + .disable = atmel_pwm_disable,
> + .owner = THIS_MODULE,
> +};
> +
> +struct atmel_pwm_data {
> + void (*config)(struct atmel_pwm_chip *chip, struct pwm_device *pwm,
> + unsigned int dty, unsigned int prd);
> +};
> +
> +static struct atmel_pwm_data atmel_pwm_data_v1 = {
> + .config = atmel_pwm_config_v1,
> +};
> +
> +static struct atmel_pwm_data atmel_pwm_data_v2 = {
> + .config = atmel_pwm_config_v2,
> +};
> +
> +static const struct of_device_id atmel_pwm_dt_ids[] = {
> + {
> + .compatible = "atmel,at91sam9rl-pwm",
> + .data = &atmel_pwm_data_v1,
> + }, {
> + .compatible = "atmel,sama5-pwm",
> + .data = &atmel_pwm_data_v2,
> + }, {
> + /* sentinel */
> + },
> +};
> +MODULE_DEVICE_TABLE(of, atmel_pwm_dt_ids);
> +
> +static int atmel_pwm_probe(struct platform_device *pdev)
> +{
> + const struct of_device_id *of_id =
> + of_match_device(atmel_pwm_dt_ids, &pdev->dev);
> + const struct atmel_pwm_data *data;
> + struct atmel_pwm_chip *atmel_pwm;
> + struct resource *res;
> + struct pinctrl *pinctrl;
> + int ret;
> +
> + pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
> + if (IS_ERR(pinctrl)) {
> + dev_err(&pdev->dev, "failed get pinctrl\n");
> + return PTR_ERR(pinctrl);
> + }
> +
> + atmel_pwm = devm_kzalloc(&pdev->dev, sizeof(*atmel_pwm), GFP_KERNEL);
> + if (!atmel_pwm) {
> + dev_err(&pdev->dev, "out of memory\n");
> + return -ENOMEM;
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res) {
> + dev_err(&pdev->dev, "no memory resource defined\n");
> + return -ENODEV;
> + }
> +
> + atmel_pwm->base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(atmel_pwm->base)) {
> + dev_err(&pdev->dev, "ioremap failed\n");
> + return PTR_ERR(atmel_pwm->base);
> + }
> +
> + atmel_pwm->clk = devm_clk_get(&pdev->dev, "pwm_clk");
> + if (IS_ERR(atmel_pwm->clk)) {
> + dev_err(&pdev->dev, "clk get failed\n");
> + return PTR_ERR(atmel_pwm->clk);
> + }
> +
> + atmel_pwm->chip.dev = &pdev->dev;
> + atmel_pwm->chip.ops = &atmel_pwm_ops;
> + atmel_pwm->chip.of_xlate = of_pwm_xlate_with_flags;
> + atmel_pwm->chip.of_pwm_n_cells = 3;
> + atmel_pwm->chip.base = -1;
> + atmel_pwm->chip.npwm = PWM_NUM;
> +
> + data = of_id->data;
> + atmel_pwm->config = data->config;
> +
> + ret = pwmchip_add(&atmel_pwm->chip);
> + if (ret < 0) {
> + dev_err(&pdev->dev, "failed to add pwm chip %d\n", ret);
> + return ret;
> + }
> +
> + platform_set_drvdata(pdev, atmel_pwm);
> +
> + dev_info(&pdev->dev, "successfully register pwm\n");
> +
> + return 0;
> +}
> +
> +static int atmel_pwm_remove(struct platform_device *pdev)
> +{
> + struct atmel_pwm_chip *atmel_pwm = platform_get_drvdata(pdev);
> +
> + return pwmchip_remove(&atmel_pwm->chip);
> +}
> +
> +static struct platform_driver atmel_pwm_driver = {
> + .driver = {
> + .name = "atmel-pwm",
> + .of_match_table = of_match_ptr(atmel_pwm_dt_ids),
> + },
> + .probe = atmel_pwm_probe,
> + .remove = atmel_pwm_remove,
> +};
> +module_platform_driver(atmel_pwm_driver);
> +
> +MODULE_ALIAS("platform:atmel-pwm");
> +MODULE_AUTHOR("Bo Shen <voice.shen at atmel.com>");
> +MODULE_DESCRIPTION("Atmel PWM driver");
> +MODULE_LICENSE("GPL v2");
>
More information about the linux-arm-kernel
mailing list