[PATCH V3 2/3] phy: Add driver for Exynos DP PHY
Jingoo Han
jg1.han at samsung.com
Tue Jul 2 02:58:44 EDT 2013
On Tuesday, July 02, 2013 4:48 AM, Sylwester Nawrocki wrote:
> On 07/01/2013 07:24 AM, Jingoo Han wrote:
> > Add a PHY provider driver for the Samsung Exynos SoC DP PHY.
> >
> > Signed-off-by: Jingoo Han<jg1.han at samsung.com>
> > Cc: Sylwester Nawrocki<s.nawrocki at samsung.com>
> > Acked-by: Felipe Balbi<balbi at ti.com>
> > ---
> > .../devicetree/bindings/phy/samsung-phy.txt | 8 ++
> > drivers/phy/Kconfig | 5 +
> > drivers/phy/Makefile | 1 +
> > drivers/phy/phy-exynos-dp-video.c | 118 ++++++++++++++++++++
> > 4 files changed, 132 insertions(+)
> > create mode 100644 drivers/phy/phy-exynos-dp-video.c
> >
> > diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt
> b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> > index 5ff208c..3fb656a 100644
> > --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
> > +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> > @@ -12,3 +12,11 @@ the PHY specifier identifies the PHY and its meaning is as follows:
> > 1 - MIPI DSIM 0,
> > 2 - MIPI CSIS 1,
> > 3 - MIPI DSIM 1.
> > +
> > +Samsung EXYNOS SoC series DP PHY
>
> I would make it "Samsung EXYNOS SoC series Display Port PHY"
OK.
>
> > +-------------------------------------------------
> > +
> > +Required properties:
> > +- compatible : should be "samsung,exynos5250-dp-video-phy";
> > +- reg : offset and length of the DP PHY register set;
> > +- #phy-cells : from the generic phy bindings, must be 0;
>
> s/phy/PHY ?
OK.
>
> > \ No newline at end of file
>
> Missing new line character.
OK.
>
> > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> > index 6f446d0..760f55a 100644
> > --- a/drivers/phy/Kconfig
> > +++ b/drivers/phy/Kconfig
> > @@ -19,4 +19,9 @@ config PHY_EXYNOS_MIPI_VIDEO
> > help
> > Support for MIPI CSI-2 and MIPI DSI DPHY found on Samsung
> > S5P and EXYNOS SoCs.
> > +
> > +config PHY_EXYNOS_DP_VIDEO
> > + tristate "EXYNOS SoC series DP PHY driver"
>
> "EXYNOS SoC series Display Port PHY driver" ?
>
> > + help
> > + Support for DP PHY found on Samsung EXYNOS SoCs.
>
> s/DP/Display Port ?
OK.
>
> > endif
> > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> > index 71d8841..0fd1340 100644
> > --- a/drivers/phy/Makefile
> > +++ b/drivers/phy/Makefile
> > @@ -4,3 +4,4 @@
> >
> > obj-$(CONFIG_GENERIC_PHY) += phy-core.o
> > obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
> > +obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
> > diff --git a/drivers/phy/phy-exynos-dp-video.c b/drivers/phy/phy-exynos-dp-video.c
> > new file mode 100644
> > index 0000000..75e1d11
> > --- /dev/null
> > +++ b/drivers/phy/phy-exynos-dp-video.c
> > @@ -0,0 +1,118 @@
> > +/*
> > + * Samsung EXYNOS SoC series DP PHY driver
>
> s/DP/Display Port ?
OK.
>
> > + *
> > + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> > + * Author: Jingoo Han<jg1.han at samsung.com>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#include<linux/io.h>
> > +#include<linux/kernel.h>
> > +#include<linux/module.h>
> > +#include<linux/of.h>
> > +#include<linux/of_address.h>
> > +#include<linux/phy/phy.h>
> > +#include<linux/platform_device.h>
> > +
> > +/* DPTX_PHY_CONTROL register */
> > +#define EXYNOS_DPTX_PHY_ENABLE (1<< 0)
> > +
> > +struct exynos_dp_video_phy {
> > + void __iomem *regs;
> > +};
> > +
> > +static int __set_phy_state(struct exynos_dp_video_phy *state, unsigned int on)
> > +{
> > + void __iomem *addr;
>
> How about just dropping this local variable ?
OK.
I will drop this local variable.
>
> > + u32 reg;
> > +
> > + addr = state->regs;
> > +
> > + reg = readl(addr);
> > + if (on)
> > + reg |= EXYNOS_DPTX_PHY_ENABLE;
> > + else
> > + reg&= ~EXYNOS_DPTX_PHY_ENABLE;
> > + writel(reg, addr);
> > +
> > + return 0;
> > +}
> > +
> > +static int exynos_dp_video_phy_power_on(struct phy *phy)
> > +{
> > + struct exynos_dp_video_phy *state = phy_get_drvdata(phy);
> > +
> > + return __set_phy_state(state, 1);
> > +}
> > +
> > +static int exynos_dp_video_phy_power_off(struct phy *phy)
> > +{
> > + struct exynos_dp_video_phy *state = phy_get_drvdata(phy);
> > +
> > + return __set_phy_state(state, 0);
> > +}
> > +
> > +static struct phy_ops exynos_dp_video_phy_ops = {
> > + .power_on = exynos_dp_video_phy_power_on,
> > + .power_off = exynos_dp_video_phy_power_off,
> > + .owner = THIS_MODULE,
> > +};
> > +
> > +static int exynos_dp_video_phy_probe(struct platform_device *pdev)
> > +{
> > + struct exynos_dp_video_phy *state;
> > + struct device *dev =&pdev->dev;
> > + struct resource *res;
> > + struct phy_provider *phy_provider;
> > + struct phy *phy;
> > +
> > + state = devm_kzalloc(dev, sizeof(*state), GFP_KERNEL);
> > + if (!state)
> > + return -ENOMEM;
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > +
> > + state->regs = devm_ioremap_resource(dev, res);
> > + if (IS_ERR(state->regs))
> > + return PTR_ERR(state->regs);
> > +
> > + dev_set_drvdata(dev, state);
>
> I can't see any corresponding dev_get_drvdata(), it should be safe
> to remove this assignment.
OK.
I will remove 'dev_set_drvdata(dev, state)'.
>
> > + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> > + if (IS_ERR(phy_provider))
> > + return PTR_ERR(phy_provider);
> > +
> > + phy = devm_phy_create(dev, 0,&exynos_dp_video_phy_ops, "dp");
>
> The label could be NULL, since there is no need to support non-dt config.
OK.
I will replace "dp" with NULL.
>
> > + if (IS_ERR(phy)) {
> > + dev_err(dev, "failed to create DP PHY\n");
> > + return PTR_ERR(phy);
> > + }
> > + phy_set_drvdata(phy, state);
> > +
> > + return 0;
> > +}
> > +
> > +#ifdef CONFIG_OF
>
> You don't use of_match_ptr() macro to assign of_match_table to the driver
> structure below. This means build with CONFIG_OF disabled is broken now.
> I would just remove that #ifdef and would make the driver depends on
> CONFIG_OF.
OK.
I will add 'depends on OF', then remove '#ifdef CONFIG_OF'.
Thank you for your detailed comment. :)
Best regards,
Jingoo Han
>
> > +static const struct of_device_id exynos_dp_video_phy_of_match[] = {
> > + { .compatible = "samsung,exynos5250-dp-video-phy" },
> > + { },
> > +};
> > +MODULE_DEVICE_TABLE(of, exynos_dp_video_phy_of_match);
> > +#endif
> > +
> > +static struct platform_driver exynos_dp_video_phy_driver = {
> > + .probe = exynos_dp_video_phy_probe,
> > + .driver = {
> > + .name = "exynos-dp-video-phy",
> > + .owner = THIS_MODULE,
> > + .of_match_table = exynos_dp_video_phy_of_match,
> > + }
> > +};
> > +module_platform_driver(exynos_dp_video_phy_driver);
> > +
> > +MODULE_AUTHOR("Jingoo Han<jg1.han at samsung.com>");
> > +MODULE_DESCRIPTION("Samsung EXYNOS SoC DP PHY driver");
> > +MODULE_LICENSE("GPL v2");
>
> Thanks,
> Sylwester
More information about the linux-arm-kernel
mailing list