[RFC PATCH 08/13] sound: sam9x5_wm8731: machine driver for at91sam9x5 wm8731 boards
Bo Shen
voice.shen at atmel.com
Mon Jul 1 23:21:15 EDT 2013
Hi Richard,
Will move this patch before 5, 6, 7?
On 7/1/2013 16:39, Richard Genoud wrote:
> From: Nicolas Ferre <nicolas.ferre at atmel.com>
>
> Description of the Asoc machine driver for an at91sam9x5 based board
> with a wm8731 audio DAC. Wm8731 is clocked by a crystal and used as a
> master on the SSC/I2S interface. Its connections are a headphone jack
> and an Line input jack.
>
> [Richard: this is based on an old patch from Nicolas that I forward
> ported and reworked to use only device tree]
>
> Signed-off-by: Nicolas Ferre <nicolas.ferre at atmel.com>
> Signed-off-by: Uwe Kleine-König <u.kleine-koenig at pengutronix.de>
> Signed-off-by: Richard Genoud <richard.genoud at gmail.com>
> ---
> sound/soc/atmel/Kconfig | 12 ++
> sound/soc/atmel/Makefile | 2 +
> sound/soc/atmel/sam9x5_wm8731.c | 232 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 246 insertions(+)
> create mode 100644 sound/soc/atmel/sam9x5_wm8731.c
>
> diff --git a/sound/soc/atmel/Kconfig b/sound/soc/atmel/Kconfig
> index 3fdd87f..f24d601 100644
> --- a/sound/soc/atmel/Kconfig
> +++ b/sound/soc/atmel/Kconfig
> @@ -13,6 +13,7 @@ config SND_ATMEL_SOC_PDC
> config SND_ATMEL_SOC_DMA
> tristate
> depends on SND_ATMEL_SOC
> + select SND_SOC_DMAENGINE_PCM
>
> config SND_ATMEL_SOC_SSC
> tristate
> @@ -32,6 +33,17 @@ config SND_AT91_SOC_SAM9G20_WM8731
> Say Y if you want to add support for SoC audio on WM8731-based
> AT91sam9g20 evaluation board.
>
> +config SND_AT91_SOC_SAM9X5_WM8731
> + tristate "SoC Audio support for WM8731-based at91sam9x5 board"
> + depends on ATMEL_SSC && SND_ATMEL_SOC && SOC_AT91SAM9X5
> + select SND_ATMEL_SOC_SSC
> + select SND_ATMEL_SOC_DMA
> + select SND_ATMEL_SOC_PDC
Not need to select SND_ATMEL_SOC_PDC
> + select SND_SOC_WM8731
> + help
> + Say Y if you want to add support for audio SoC on an
> + at91sam9x5 based board that is using WM8731 codec.
> +
> config SND_AT91_SOC_AFEB9260
> tristate "SoC Audio support for AFEB9260 board"
> depends on ARCH_AT91 && ATMEL_SSC && ARCH_AT91 && MACH_AFEB9260 && SND_ATMEL_SOC
> diff --git a/sound/soc/atmel/Makefile b/sound/soc/atmel/Makefile
> index 41967cc..7784c09 100644
> --- a/sound/soc/atmel/Makefile
> +++ b/sound/soc/atmel/Makefile
> @@ -11,6 +11,8 @@ obj-$(CONFIG_SND_ATMEL_SOC_SSC) += snd-soc-atmel_ssc_dai.o
>
> # AT91 Machine Support
> snd-soc-sam9g20-wm8731-objs := sam9g20_wm8731.o
> +snd-soc-sam9x5-wm8731-objs := sam9x5_wm8731.o
>
> obj-$(CONFIG_SND_AT91_SOC_SAM9G20_WM8731) += snd-soc-sam9g20-wm8731.o
> +obj-$(CONFIG_SND_AT91_SOC_SAM9X5_WM8731) += snd-soc-sam9x5-wm8731.o
> obj-$(CONFIG_SND_AT91_SOC_AFEB9260) += snd-soc-afeb9260.o
> diff --git a/sound/soc/atmel/sam9x5_wm8731.c b/sound/soc/atmel/sam9x5_wm8731.c
> new file mode 100644
> index 0000000..83ca457
> --- /dev/null
> +++ b/sound/soc/atmel/sam9x5_wm8731.c
> @@ -0,0 +1,232 @@
> +/*
> + * sam9x5_wm8731 -- SoC audio for AT91SAM9X5-based boards
> + * that are using WM8731 as codec.
> + *
> + * Copyright (C) 2011 Atmel,
> + * Nicolas Ferre <nicolas.ferre at atmel.com>
> + *
> + * Based on sam9g20_wm8731.c by:
> + * Sedji Gaouaou <sedji.gaouaou at atmel.com>
> + *
> + * GPL
> + */
> +#include <linux/module.h>
> +#include <linux/moduleparam.h>
> +#include <linux/kernel.h>
> +#include <linux/clk.h>
> +#include <linux/timer.h>
> +#include <linux/interrupt.h>
> +#include <linux/platform_device.h>
> +#include <linux/i2c.h>
> +
> +#include <linux/atmel-ssc.h>
> +
> +#include <sound/core.h>
> +#include <sound/pcm.h>
> +#include <sound/pcm_params.h>
> +#include <sound/soc.h>
> +
> +#include <asm/mach-types.h>
> +#include <mach/hardware.h>
> +#include <mach/gpio.h>
> +
> +#include "../codecs/wm8731.h"
> +#include "atmel-pcm.h"
> +#include "atmel_ssc_dai.h"
> +
> +#define MCLK_RATE 12288000
> +
> +#define DRV_NAME "sam9x5-snd-wm8731"
> +
> +/*
> + * Audio paths on at91sam9x5ek board:
> + *
> + * |A| ------------> | | ---R----> Headphone Jack
> + * |T| <----\ | WM | ---L--/
> + * |9| ---> CLK <--> | 8751 | <--R----- Line In Jack
> + * |1| <------------ | | <--L--/
> + */
> +static const struct snd_soc_dapm_widget at91sam9x5ek_dapm_widgets[] = {
> + SND_SOC_DAPM_HP("Headphone Jack", NULL),
> + SND_SOC_DAPM_LINE("Line In Jack", NULL),
> +};
> +
> +/*
> + * Logic for a wm8731 as connected on a at91sam9x5 based board.
> + */
> +static int at91sam9x5ek_wm8731_init(struct snd_soc_pcm_runtime *rtd)
> +{
> + struct snd_soc_codec *codec = rtd->codec;
> + struct snd_soc_dai *codec_dai = rtd->codec_dai;
> + struct snd_soc_dapm_context *dapm = &codec->dapm;
> + struct device *dev = rtd->dev;
> + int ret;
> +
> + dev_dbg(dev, "ASoC: at91sam9x5ek_wm8731_init() called\n");
> +
> + /*
> + * remove some not supported rates in relation with clock
> + * provided to the wm8731 codec
> + */
> + switch (MCLK_RATE) {
> + case 12288000:
> + codec_dai->driver->playback.rates &= SNDRV_PCM_RATE_8000 |
> + SNDRV_PCM_RATE_32000 |
> + SNDRV_PCM_RATE_48000 |
> + SNDRV_PCM_RATE_96000;
> + codec_dai->driver->capture.rates &= SNDRV_PCM_RATE_8000 |
> + SNDRV_PCM_RATE_32000 |
> + SNDRV_PCM_RATE_48000 |
> + SNDRV_PCM_RATE_96000;
> + break;
> + case 12000000:
> + /* all wm8731 rates supported */
> + break;
> + default:
> + dev_err(dev, "ASoC: Codec Master clock rate not defined\n");
> + return -EINVAL;
> + }
Here, I think we not need to use switch ... case, as the MCLK_RATE is
hard code as 12288000.
-----------------------------------------------
> + /* set not connected pins */
> + snd_soc_dapm_nc_pin(dapm, "Mic Bias");
> + snd_soc_dapm_nc_pin(dapm, "MICIN");
> + snd_soc_dapm_nc_pin(dapm, "LOUT");
> + snd_soc_dapm_nc_pin(dapm, "ROUT");
> +
> + /* always connected */
> + snd_soc_dapm_enable_pin(dapm, "Headphone Jack");
> + snd_soc_dapm_enable_pin(dapm, "Line In Jack");
------------------------------------------------
This part, not needed, as to the ASoC framework will deal with it.
> + /* set the codec system clock for DAC and ADC */
> + ret = snd_soc_dai_set_sysclk(codec_dai, WM8731_SYSCLK_XTAL,
> + MCLK_RATE, SND_SOC_CLOCK_IN);
> + if (ret < 0) {
> + dev_err(dev, "ASoC: Failed to set WM8731 SYSCLK: %d\n", ret);
> + return ret;
> + }
> +
> + /* signal a DAPM event */
> + snd_soc_dapm_sync(dapm);
> + return 0;
> +}
> +
> +static int sam9x5_wm8731_driver_probe(struct platform_device *pdev)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + struct device_node *codec_np, *cpu_np;
> + struct snd_soc_card *card;
> + struct snd_soc_dai_link *dai;
> + int ret;
> +
> + if (!np) {
> + dev_err(&pdev->dev, "No device node supplied\n");
> + return -EINVAL;
> + }
> +
> + ret = atmel_ssc_set_audio(0);
> + if (ret != 0) {
> + dev_err(&pdev->dev,
> + "ASoC: Failed to set SSC 0 for audio: %d\n", ret);
> + return ret;
> + }
> +
> + card = devm_kzalloc(&pdev->dev, sizeof(*card), GFP_KERNEL);
> + dai = devm_kzalloc(&pdev->dev, sizeof(*dai), GFP_KERNEL);
> + if (!dai || !card) {
> + ret = -ENOMEM;
> + goto out;
> + }
> +
> + card->dev = &pdev->dev;
> + card->owner = THIS_MODULE;
> + card->dai_link = dai;
> + card->num_links = 1;
> + dai->name = "WM8731";
> + dai->stream_name = "WM8731 PCM";
> + dai->codec_dai_name = "wm8731-hifi";
> + dai->init = at91sam9x5ek_wm8731_init;
> + card->dapm_widgets = at91sam9x5ek_dapm_widgets;
> + card->num_dapm_widgets = ARRAY_SIZE(at91sam9x5ek_dapm_widgets);
Will keep these as snd_soc_card and snd_soc_dai_link structure separately?
> + ret = snd_soc_of_parse_card_name(card, "atmel,model");
> + if (ret)
> + goto out;
> +
> + ret = snd_soc_of_parse_audio_routing(card, "atmel,audio-routing");
> + if (ret)
> + goto out;
> +
> + codec_np = of_parse_phandle(np, "atmel,audio-codec", 0);
> + if (!codec_np) {
> + dev_err(&pdev->dev, "codec info missing\n");
> + ret = -EINVAL;
> + goto out;
> + }
> +
> + dai->codec_of_node = codec_np;
> +
> + cpu_np = of_parse_phandle(np, "atmel,ssc-controller", 0);
> + if (!cpu_np) {
> + dev_err(&pdev->dev, "ssc controller node missing\n");
> + ret = -EINVAL;
> + goto out;
> + }
> + dai->cpu_of_node = cpu_np;
> + dai->platform_of_node = cpu_np;
> +
> + of_node_put(codec_np);
> + of_node_put(cpu_np);
> +
> + dai->dai_fmt = snd_soc_of_parse_daifmt(np, "atmel,");
> +
> + ret = snd_soc_register_card(card);
> + if (ret) {
> + dev_err(&pdev->dev,
> + "ASoC: Platform device allocation failed\n");
> + goto out;
> + }
> +
> + platform_set_drvdata(pdev, card);
> +
> + dev_info(&pdev->dev, "ASoC: at91sam9x5ek_init ok\n");
> +
> + return ret;
> +
> +out:
> + atmel_ssc_put_audio(0);
> + return ret;
> +}
> +
> +static int sam9x5_wm8731_driver_remove(struct platform_device *pdev)
> +{
> + struct snd_soc_card *card = platform_get_drvdata(pdev);
> +
> + snd_soc_unregister_card(card);
> + atmel_ssc_put_audio(0);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id sam9x5_wm8731_of_match[] = {
> + { .compatible = "atmel,sam9x5-audio-wm8731", },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, sam9x5_wm8731_of_match);
> +
> +static struct platform_driver sam9x5_wm8731_driver = {
> + .driver = {
> + .name = DRV_NAME,
> + .owner = THIS_MODULE,
> + .of_match_table = of_match_ptr(sam9x5_wm8731_of_match),
> + },
> + .probe = sam9x5_wm8731_driver_probe,
> + .remove = sam9x5_wm8731_driver_remove,
> +};
> +module_platform_driver(sam9x5_wm8731_driver);
> +
> +/* Module information */
> +MODULE_AUTHOR("Nicolas Ferre <nicolas.ferre at atmel.com>");
> +MODULE_AUTHOR("Richard Genoud <richard.genoud at gmail.com>");
> +MODULE_DESCRIPTION("ALSA SoC machine driver for AT91SAM9x5 - WM8731");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("platform:" DRV_NAME);
>
Best Regards,
Bo Shen
More information about the linux-arm-kernel
mailing list