[v2 4/4] sata: imx: add ahci sata support on imx platforms
Girish K S
girish.shivananjappa at linaro.org
Mon Jul 1 07:27:35 EDT 2013
Hello Richard,
Instead of writing a separate driver for the changes you mentioned in
the commit message. you can just add those changes to
the platform data (pdata-> init).
On 1 July 2013 15:32, Richard Zhu <richard.zhuhongxing at gmail.com> wrote:
> imx6q contains one Synopsys AHCI SATA controller,
> But it can't shares ahci_platform driver with other
> controllers.
> Because there are some misalignments of the bits
> definitions of the HBA registers and the Vendor
> Specific registers
> - CAP_SSS(bit20) of the HOST_CAP is writable, default
> value is '0', should be configured to be '1'
> - bit0 (only one AHCI SATA port on imx6q) of the
> HOST_PORTS_IMPL should be set to be '1'.(default 0)
> - One Vendor Specific register HOST_TIMER1MS(offset:0xe0)
> should be configured regarding to the frequency of AHB
> bus clock.
>
> Setup its own ahci sata driver, enable the imx6q ahci
> sata support, and update the ahci sata binding document.
>
> Signed-off-by: Richard Zhu <r65037 at freescale.com>
> ---
> .../devicetree/bindings/ata/ahci-platform.txt | 2 +-
> drivers/ata/Kconfig | 8 +
> drivers/ata/Makefile | 1 +
> drivers/ata/sata_imx.c | 349 ++++++++++++++++++++
> 4 files changed, 359 insertions(+), 1 deletions(-)
> create mode 100644 drivers/ata/sata_imx.c
>
> diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt
> index b519f9b..e252620 100644
> --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt
> +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt
> @@ -4,7 +4,7 @@ SATA nodes are defined to describe on-chip Serial ATA controllers.
> Each SATA controller should have its own node.
>
> Required properties:
> -- compatible : compatible list, contains "calxeda,hb-ahci" or "snps,spear-ahci"
> +- compatible : compatible list, contains "calxeda,hb-ahci", "snps,spear-ahci" or "snps, imx-ahci"
> - interrupts : <interrupt mapping for SATA IRQ>
> - reg : <registers mapping>
>
> diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
> index a5a3ebc..893fa0b 100644
> --- a/drivers/ata/Kconfig
> +++ b/drivers/ata/Kconfig
> @@ -236,6 +236,14 @@ config SATA_HIGHBANK
>
> If unsure, say N.
>
> +config SATA_IMX
> + tristate "Freescale iMX AHCI SATA support"
> + help
> + This option enables support for the Freescale iMX SoC's
> + onboard AHCI SATA.
> +
> + If unsure, say N.
> +
> config SATA_MV
> tristate "Marvell SATA support"
> help
> diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
> index c04d0fd..c40b328 100644
> --- a/drivers/ata/Makefile
> +++ b/drivers/ata/Makefile
> @@ -10,6 +10,7 @@ obj-$(CONFIG_SATA_INIC162X) += sata_inic162x.o
> obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
> obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o
> obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o
> +obj-$(CONFIG_SATA_IMX) += sata_imx.o libahci.o
>
> # SFF w/ custom DMA
> obj-$(CONFIG_PDC_ADMA) += pdc_adma.o
> diff --git a/drivers/ata/sata_imx.c b/drivers/ata/sata_imx.c
> new file mode 100644
> index 0000000..2be92e8
> --- /dev/null
> +++ b/drivers/ata/sata_imx.c
> @@ -0,0 +1,349 @@
> +/*
> + * Freescale IMX AHCI SATA platform driver
> + * Copyright 2013 Freescale Semiconductor, Inc.
> + *
> + * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
> + * more details.
> + *
> + * You should have received a copy of the GNU General Public License along with
> + * this program. If not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/kernel.h>
> +#include <linux/gfp.h>
> +#include <linux/module.h>
> +#include <linux/pm.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/device.h>
> +#include <linux/platform_device.h>
> +#include <linux/libata.h>
> +#include <linux/ahci_platform.h>
> +#include "ahci.h"
> +
> +enum {
> + HOST_TIMER1MS = 0xe0, /* Timer 1-ms */
> +};
> +
> +static void ahci_imx_host_stop(struct ata_host *host);
> +
> +static struct ata_port_operations ahci_imx_platform_ops = {
> + .inherits = &ahci_ops,
> + .host_stop = ahci_imx_host_stop,
> +};
> +
> +static const struct ata_port_info ahci_imx_port_info = {
> + .flags = AHCI_FLAG_COMMON,
> + .pio_mask = ATA_PIO4,
> + .udma_mask = ATA_UDMA6,
> + .port_ops = &ahci_imx_platform_ops,
> +};
> +
> +static struct scsi_host_template ahci_imx_platform_sht = {
> + AHCI_SHT("sata_imx"),
> +};
> +
> +/*
> + * Configure the HWINIT bits of the HOST_CAP and HOST_PORTS_IMPL,
> + * and IP vendor specific register HOST_TIMER1MS.
> + *
> + * Configure CAP_SSS (support stagered spin up).
> + * Implement the port0.
> + * Get the ahb clock rate, and configure the TIMER1MS register.
> + */
> +static int imx_sata_init(void __iomem *mmio)
> +{
> + int ret;
> + struct clk *ahb_clk;
> +
> + ret = readl(mmio + HOST_CAP);
> + if (!(ret & HOST_CAP_SSS))
> + writel(ret |= HOST_CAP_SSS, mmio + HOST_CAP);
> + ret = readl(mmio + HOST_PORTS_IMPL);
> + if (!(ret & 0x1))
> + writel((ret | 0x1), mmio + HOST_PORTS_IMPL);
> + ahb_clk = clk_get_sys(NULL, "ahb");
> + if (IS_ERR(ahb_clk)) {
> + pr_err("no ahb clock.\n");
> + ret = PTR_ERR(ahb_clk);
> + return ret;
> + }
> + ret = clk_get_rate(ahb_clk) / 1000;
> + clk_put(ahb_clk);
> + writel(ret, mmio + HOST_TIMER1MS);
> +
> + return ret;
> +}
> +
> +static int ahci_imx_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct ahci_platform_data *pdata = dev_get_platdata(dev);
> + struct ata_port_info pi = ahci_imx_port_info;
> + const struct ata_port_info *ppi[] = { &pi, NULL };
> + struct ahci_host_priv *hpriv;
> + struct ata_host *host;
> + struct resource *mem;
> + int irq;
> + int n_ports;
> + int i;
> + int rc;
> +
> + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!mem) {
> + dev_err(dev, "no mmio space\n");
> + return -EINVAL;
> + }
> +
> + irq = platform_get_irq(pdev, 0);
> + if (irq <= 0) {
> + dev_err(dev, "no irq\n");
> + return -EINVAL;
> + }
> +
> + if (pdata && pdata->ata_port_info)
> + pi = *pdata->ata_port_info;
> +
> + hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
> + if (!hpriv) {
> + dev_err(dev, "can't alloc ahci_host_priv\n");
> + return -ENOMEM;
> + }
> +
> + hpriv->flags |= (unsigned long)pi.private_data;
> +
> + hpriv->mmio = devm_ioremap(dev, mem->start, resource_size(mem));
> + if (!hpriv->mmio) {
> + dev_err(dev, "can't map %pR\n", mem);
> + return -ENOMEM;
> + }
> +
> + hpriv->clk = clk_get(dev, NULL);
> + if (IS_ERR(hpriv->clk)) {
> + dev_err(dev, "can't get clock\n");
> + } else {
> + rc = clk_prepare_enable(hpriv->clk);
> + if (rc) {
> + dev_err(dev, "clock prepare enable failed");
> + goto free_clk;
> + }
> + }
> +
> + /*
> + * Some platforms might need to prepare for mmio region access,
> + * which could be done in the following init call. So, the mmio
> + * region shouldn't be accessed before init (if provided) has
> + * returned successfully.
> + */
> + if (pdata && pdata->init) {
> + rc = pdata->init(dev, hpriv->mmio);
> + if (rc)
> + goto disable_unprepare_clk;
> + }
> +
> + rc = imx_sata_init(hpriv->mmio);
> + if (rc < 0)
> + goto pdata_exit;
> +
> + ahci_save_initial_config(dev, hpriv,
> + pdata ? pdata->force_port_map : 0,
> + pdata ? pdata->mask_port_map : 0);
> +
> + /* prepare host */
> + if (hpriv->cap & HOST_CAP_NCQ)
> + pi.flags |= ATA_FLAG_NCQ;
> +
> + if (hpriv->cap & HOST_CAP_PMP)
> + pi.flags |= ATA_FLAG_PMP;
> +
> + ahci_set_em_messages(hpriv, &pi);
> +
> + /* CAP.NP sometimes indicate the index of the last enabled
> + * port, at other times, that of the last possible port, so
> + * determining the maximum port number requires looking at
> + * both CAP.NP and port_map.
> + */
> + n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
> +
> + host = ata_host_alloc_pinfo(dev, ppi, n_ports);
> + if (!host) {
> + rc = -ENOMEM;
> + goto pdata_exit;
> + }
> +
> + host->private_data = hpriv;
> +
> + if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss)
> + host->flags |= ATA_HOST_PARALLEL_SCAN;
> + else
> + dev_info(dev, "ahci: SSS flag set, parallel bus scan disabled\n");
> +
> + if (pi.flags & ATA_FLAG_EM)
> + ahci_reset_em(host);
> +
> + for (i = 0; i < host->n_ports; i++) {
> + struct ata_port *ap = host->ports[i];
> +
> + ata_port_desc(ap, "mmio %pR", mem);
> + ata_port_desc(ap, "port 0x%x", 0x100 + ap->port_no * 0x80);
> +
> + /* set enclosure management message type */
> + if (ap->flags & ATA_FLAG_EM)
> + ap->em_message_type = hpriv->em_msg_type;
> +
> + /* disabled/not-implemented port */
> + if (!(hpriv->port_map & (1 << i)))
> + ap->ops = &ata_dummy_port_ops;
> + }
> +
> + rc = ahci_reset_controller(host);
> + if (rc)
> + goto pdata_exit;
> +
> + ahci_init_controller(host);
> + ahci_print_info(host, "platform");
> +
> + rc = ata_host_activate(host, irq, ahci_interrupt, IRQF_SHARED,
> + &ahci_imx_platform_sht);
> + if (rc)
> + goto pdata_exit;
> +
> + return 0;
> +pdata_exit:
> + if (pdata && pdata->exit)
> + pdata->exit(dev);
> +disable_unprepare_clk:
> + if (!IS_ERR(hpriv->clk))
> + clk_disable_unprepare(hpriv->clk);
> +free_clk:
> + if (!IS_ERR(hpriv->clk))
> + clk_put(hpriv->clk);
> + return rc;
> +}
> +
> +static void ahci_imx_host_stop(struct ata_host *host)
> +{
> + struct device *dev = host->dev;
> + struct ahci_platform_data *pdata = dev_get_platdata(dev);
> + struct ahci_host_priv *hpriv = host->private_data;
> +
> + if (pdata && pdata->exit)
> + pdata->exit(dev);
> +
> + if (!IS_ERR(hpriv->clk)) {
> + clk_disable_unprepare(hpriv->clk);
> + clk_put(hpriv->clk);
> + }
> +}
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int ahci_imx_suspend(struct device *dev)
> +{
> + struct ahci_platform_data *pdata = dev_get_platdata(dev);
> + struct ata_host *host = dev_get_drvdata(dev);
> + struct ahci_host_priv *hpriv = host->private_data;
> + void __iomem *mmio = hpriv->mmio;
> + u32 ctl;
> + int rc;
> +
> + if (hpriv->flags & AHCI_HFLAG_NO_SUSPEND) {
> + dev_err(dev, "firmware update required for suspend/resume\n");
> + return -EIO;
> + }
> +
> + /*
> + * AHCI spec rev1.1 section 8.3.3:
> + * Software must disable interrupts prior to requesting a
> + * transition of the HBA to D3 state.
> + */
> + ctl = readl(mmio + HOST_CTL);
> + ctl &= ~HOST_IRQ_EN;
> + writel(ctl, mmio + HOST_CTL);
> + readl(mmio + HOST_CTL); /* flush */
> +
> + rc = ata_host_suspend(host, PMSG_SUSPEND);
> + if (rc)
> + return rc;
> +
> + if (pdata && pdata->suspend)
> + return pdata->suspend(dev);
> +
> + if (!IS_ERR(hpriv->clk))
> + clk_disable_unprepare(hpriv->clk);
> +
> + return 0;
> +}
> +
> +static int ahci_imx_resume(struct device *dev)
> +{
> + struct ahci_platform_data *pdata = dev_get_platdata(dev);
> + struct ata_host *host = dev_get_drvdata(dev);
> + struct ahci_host_priv *hpriv = host->private_data;
> + int rc;
> +
> + if (!IS_ERR(hpriv->clk)) {
> + rc = clk_prepare_enable(hpriv->clk);
> + if (rc) {
> + dev_err(dev, "clock prepare enable failed");
> + return rc;
> + }
> + }
> +
> + if (pdata && pdata->resume) {
> + rc = pdata->resume(dev);
> + if (rc)
> + goto disable_unprepare_clk;
> + }
> +
> + if (dev->power.power_state.event == PM_EVENT_SUSPEND) {
> + rc = ahci_reset_controller(host);
> + if (rc)
> + goto disable_unprepare_clk;
> +
> + ahci_init_controller(host);
> + }
> +
> + ata_host_resume(host);
> +
> + return 0;
> +
> +disable_unprepare_clk:
> + if (!IS_ERR(hpriv->clk))
> + clk_disable_unprepare(hpriv->clk);
> +
> + return rc;
> +}
> +#endif
> +
> +static SIMPLE_DEV_PM_OPS(ahci_imx_pm_ops, ahci_imx_suspend, ahci_imx_resume);
> +
> +static const struct of_device_id ahci_of_match[] = {
> + { .compatible = "snps,imx-ahci", },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, ahci_of_match);
> +
> +static struct platform_driver ahci_imx_driver = {
> + .probe = ahci_imx_probe,
> + .remove = ata_platform_remove_one,
> + .driver = {
> + .name = "imx-ahci",
> + .owner = THIS_MODULE,
> + .of_match_table = ahci_of_match,
> + .pm = &ahci_imx_pm_ops,
> + },
> +};
> +module_platform_driver(ahci_imx_driver);
> +
> +MODULE_DESCRIPTION("FREESCALE IMX AHCI SATA platform driver");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("sata:imx");
> --
> 1.7.5.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-ide" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
More information about the linux-arm-kernel
mailing list