[PATCH 4/4] drivers: usb: start using the control module driver
Felipe Balbi
balbi at ti.com
Fri Jan 18 07:02:56 EST 2013
Hi,
On Fri, Jan 18, 2013 at 03:10:45PM +0530, Kishon Vijay Abraham I wrote:
> Start using the control module driver for powering on the PHY and for
> writing to the mailbox instead of writing to the control module
> registers on their own.
>
> Signed-off-by: Kishon Vijay Abraham I <kishon at ti.com>
> ---
> Documentation/devicetree/bindings/usb/omap-usb.txt | 4 ++
> Documentation/devicetree/bindings/usb/usb-phy.txt | 7 +--
> arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 13 ----
> drivers/usb/musb/Kconfig | 1 +
> drivers/usb/musb/omap2430.c | 64 ++++++++------------
> drivers/usb/musb/omap2430.h | 9 ---
> drivers/usb/phy/Kconfig | 1 +
> drivers/usb/phy/omap-usb2.c | 38 +++---------
> include/linux/usb/omap_usb.h | 4 +-
> 9 files changed, 42 insertions(+), 99 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
> index ead6ba9..8bedbba 100644
> --- a/Documentation/devicetree/bindings/usb/omap-usb.txt
> +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
> @@ -3,6 +3,9 @@ OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
> OMAP MUSB GLUE
> - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
> - ti,hwmods : must be "usb_otg_hs"
> + - ti,has_mailbox : to specify that omap uses an external mailbox
> + (in control module) to communicate with the musb core during device connect
> + and disconnect.
> - multipoint : Should be "1" indicating the musb controller supports
> multipoint. This is a MUSB configuration-specific setting.
> - num_eps : Specifies the number of endpoints. This is also a
> @@ -24,6 +27,7 @@ SOC specific device node entry
> usb_otg_hs: usb_otg_hs at 4a0ab000 {
> compatible = "ti,omap4-musb";
> ti,hwmods = "usb_otg_hs";
> + ti,has_mailbox;
> multipoint = <1>;
> num_eps = <16>;
> ram_bits = <12>;
> diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt
> index 2466b6f..48761a2 100644
> --- a/Documentation/devicetree/bindings/usb/usb-phy.txt
> +++ b/Documentation/devicetree/bindings/usb/usb-phy.txt
> @@ -4,9 +4,7 @@ OMAP USB2 PHY
>
> Required properties:
> - compatible: Should be "ti,omap-usb2"
> - - reg : Address and length of the register set for the device. Also
> -add the address of control module dev conf register until a driver for
> -control module is added
> + - reg : Address and length of the register set for the device.
>
> Optional properties:
> - ctrl_module : phandle of the control module used by PHY driver to power on
> @@ -16,7 +14,6 @@ This is usually a subnode of ocp2scp to which it is connected.
>
> usb2phy at 4a0ad080 {
> compatible = "ti,omap-usb2";
> - reg = <0x4a0ad080 0x58>,
> - <0x4a002300 0x4>;
> + reg = <0x4a0ad080 0x58>;
> ctrl_module = <&omap_control_usb>;
> };
> diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
> index 129d508..103f4ba 100644
> --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
> +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
> @@ -2698,13 +2698,6 @@ static struct resource omap44xx_usb_phy_and_pll_addrs[] = {
> .end = 0x4a0ae000,
> .flags = IORESOURCE_MEM,
> },
> - {
> - /* XXX: Remove this once control module driver is in place */
> - .name = "ctrl_dev",
> - .start = 0x4a002300,
> - .end = 0x4a002303,
> - .flags = IORESOURCE_MEM,
> - },
> { }
> };
>
> @@ -6152,12 +6145,6 @@ static struct omap_hwmod_addr_space omap44xx_usb_otg_hs_addrs[] = {
> .pa_end = 0x4a0ab7ff,
> .flags = ADDR_TYPE_RT
> },
> - {
> - /* XXX: Remove this once control module driver is in place */
> - .pa_start = 0x4a00233c,
> - .pa_end = 0x4a00233f,
> - .flags = ADDR_TYPE_RT
> - },
> { }
> };
>
> diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig
> index 23a0b7f..de6e5ce 100644
> --- a/drivers/usb/musb/Kconfig
> +++ b/drivers/usb/musb/Kconfig
> @@ -11,6 +11,7 @@ config USB_MUSB_HDRC
> select NOP_USB_XCEIV if (SOC_TI81XX || SOC_AM33XX)
> select TWL4030_USB if MACH_OMAP_3430SDP
> select TWL6030_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA
> + select OMAP_CONTROL_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA
> select USB_OTG_UTILS
> help
> Say Y here if your system has a dual role high speed USB
> diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
> index da00af4..3e7ceef 100644
> --- a/drivers/usb/musb/omap2430.c
> +++ b/drivers/usb/musb/omap2430.c
> @@ -37,6 +37,7 @@
> #include <linux/err.h>
> #include <linux/delay.h>
> #include <linux/usb/musb-omap.h>
> +#include <linux/usb/omap_control_usb.h>
>
> #include "musb_core.h"
> #include "omap2430.h"
> @@ -46,7 +47,7 @@ struct omap2430_glue {
> struct platform_device *musb;
> enum omap_musb_vbus_id_status status;
> struct work_struct omap_musb_mailbox_work;
> - u32 __iomem *control_otghs;
> + struct device *control_otghs;
> };
> #define glue_to_musb(g) platform_get_drvdata(g->musb)
>
> @@ -54,26 +55,6 @@ struct omap2430_glue *_glue;
>
> static struct timer_list musb_idle_timer;
>
> -/**
> - * omap4_usb_phy_mailbox - write to usb otg mailbox
> - * @glue: struct omap2430_glue *
> - * @val: the value to be written to the mailbox
> - *
> - * On detection of a device (ID pin is grounded), this API should be called
> - * to set AVALID, VBUSVALID and ID pin is grounded.
> - *
> - * When OMAP is connected to a host (OMAP in device mode), this API
> - * is called to set AVALID, VBUSVALID and ID pin in high impedance.
> - *
> - * XXX: This function will be removed once we have a seperate driver for
> - * control module
> - */
> -static void omap4_usb_phy_mailbox(struct omap2430_glue *glue, u32 val)
> -{
> - if (glue->control_otghs)
> - writel(val, glue->control_otghs);
> -}
> -
> static void musb_do_idle(unsigned long _musb)
> {
> struct musb *musb = (void *)_musb;
> @@ -269,7 +250,6 @@ EXPORT_SYMBOL_GPL(omap_musb_mailbox);
>
> static void omap_musb_set_mailbox(struct omap2430_glue *glue)
> {
> - u32 val;
> struct musb *musb = glue_to_musb(glue);
> struct device *dev = musb->controller;
> struct musb_hdrc_platform_data *pdata = dev->platform_data;
> @@ -285,8 +265,8 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
> musb->xceiv->last_event = USB_EVENT_ID;
> if (musb->gadget_driver) {
> pm_runtime_get_sync(dev);
> - val = AVALID | VBUSVALID;
> - omap4_usb_phy_mailbox(glue, val);
> + if (!IS_ERR(glue->control_otghs))
> + omap_control_usb_host_mode(glue->control_otghs);
you could introduce a helper to do the checks for you. something like:
static inline void omap_control_set_mode(*ctrl, int mode)
{
if (IS_ERR(glue->control_otghs))
return;
switch (mode) {
case HOST:
omap_control_usb_host_mode(ctrl);
break;
case DEVICE:
omap_control_usb_device(ctrl)
break;
default:
meh();
}
}
likewise for power() method
--
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20130118/18b3d6d3/attachment.sig>
More information about the linux-arm-kernel
mailing list