[PATCH v3 3/3] usb: chipidea: imx: Add system suspend/resume API

Peter Chen peter.chen at freescale.com
Wed Jan 16 03:59:05 EST 2013


During the system suspend/resume procedure, the USB also
needs to go suspend/resume procedure, this patch adds
related APIs. It is tested at i.mx6q sabrelite. Meanwhile,
it fixes the bug that the USB will out of work after
system suspend/resume.

Signed-off-by: Peter Chen <peter.chen at freescale.com>
---
 drivers/usb/chipidea/bits.h        |    1 +
 drivers/usb/chipidea/ci13xxx_imx.c |   61 ++++++++++++++++++++++++++++++++++++
 2 files changed, 62 insertions(+), 0 deletions(-)

diff --git a/drivers/usb/chipidea/bits.h b/drivers/usb/chipidea/bits.h
index ba9c6ef..d1467bb 100644
--- a/drivers/usb/chipidea/bits.h
+++ b/drivers/usb/chipidea/bits.h
@@ -47,6 +47,7 @@
 #define PORTSC_FPR            BIT(6)
 #define PORTSC_SUSP           BIT(7)
 #define PORTSC_HSP            BIT(9)
+#define PORTSC_PHCD           BIT(23) /* phy suspend mode */
 #define PORTSC_PTC            (0x0FUL << 16)
 
 /* DEVLC */
diff --git a/drivers/usb/chipidea/ci13xxx_imx.c b/drivers/usb/chipidea/ci13xxx_imx.c
index 342eab0..dd257b1 100644
--- a/drivers/usb/chipidea/ci13xxx_imx.c
+++ b/drivers/usb/chipidea/ci13xxx_imx.c
@@ -25,6 +25,7 @@
 #include <linux/mfd/syscon.h>
 
 #include "ci.h"
+#include "bits.h"
 #include "ci13xxx_imx.h"
 
 #define pdev_to_phy(pdev) \
@@ -321,6 +322,63 @@ static int ci13xxx_imx_remove(struct platform_device *pdev)
 	return 0;
 }
 
+#ifdef CONFIG_PM
+static int ci13xxx_imx_suspend(struct device *dev)
+{
+	struct ci13xxx_imx_data *data =
+		platform_get_drvdata(to_platform_device(dev));
+	struct platform_device *plat_ci;
+	struct ci13xxx	*ci;
+
+	plat_ci = data->ci_pdev;
+	ci = platform_get_drvdata(plat_ci);
+
+	hw_write(ci, OP_PORTSC, PORTSC_PHCD, 1);
+
+	if (data->phy)
+		usb_phy_set_suspend(data->phy, 1);
+
+	clk_disable_unprepare(data->clk);
+
+	return 0;
+}
+
+static int ci13xxx_imx_resume(struct device *dev)
+{
+	int ret;
+	struct ci13xxx_imx_data *data =
+		platform_get_drvdata(to_platform_device(dev));
+	struct platform_device *plat_ci;
+	struct ci13xxx	*ci;
+
+	plat_ci = data->ci_pdev;
+	ci = platform_get_drvdata(plat_ci);
+
+	ret = clk_prepare_enable(data->clk);
+	if (ret) {
+		dev_err(dev,
+			"Failed to prepare or enable clock, err=%d\n", ret);
+		return ret;
+	}
+
+	if (hw_read(ci, OP_PORTSC, PORTSC_PHCD)) {
+		hw_write(ci, OP_PORTSC, PORTSC_PHCD, 0);
+		/* Some clks sync between Controller and USB PHY */
+		mdelay(1);
+	}
+
+	if (data->phy)
+		usb_phy_set_suspend(data->phy, 0);
+
+	return ret;
+}
+
+static const struct dev_pm_ops ci13xxx_imx_pm_ops = {
+	.suspend	= ci13xxx_imx_suspend,
+	.resume		= ci13xxx_imx_resume,
+};
+#endif
+
 static const struct of_device_id ci13xxx_imx_dt_ids[] = {
 	{ .compatible = "fsl,imx27-usb", },
 	{ /* sentinel */ }
@@ -334,6 +392,9 @@ static struct platform_driver ci13xxx_imx_driver = {
 		.name = "imx_usb",
 		.owner = THIS_MODULE,
 		.of_match_table = ci13xxx_imx_dt_ids,
+#ifdef CONFIG_PM
+		.pm	= &ci13xxx_imx_pm_ops,
+#endif
 	 },
 };
 
-- 
1.7.0.4





More information about the linux-arm-kernel mailing list