[PATCH 08/16] ARM: bL_platsmp.c: make sure the GIC interface of a dying CPU is disabled

[Santosh Shilimkar]

On Saturday 12 January 2013 10:17 PM, Nicolas Pitre wrote:
> On Sat, 12 Jan 2013, Santosh Shilimkar wrote:
>
>> On Saturday 12 January 2013 12:37 AM, Nicolas Pitre wrote:
>>> On Fri, 11 Jan 2013, Santosh Shilimkar wrote:
>>>
>>>> On Thursday 10 January 2013 05:50 AM, Nicolas Pitre wrote:
>>>>> Otherwise there might be some interrupts or IPIs becoming pending and
>>>>> the
>>>>> CPU will not enter low power mode when doing a WFI.  The effect of this
>>>>> is a CPU that loops back into the kernel, go through the first man
>>>>> election, signals itself as alive,  and prevent the cluster from being
>>>>> shut down.
>>>>>
>>>>> This could benefit from a better solution.
>>>>>
>>>>> Signed-off-by: Nicolas Pitre <nico at linaro.org>
>>>>> ---
>>>>>     arch/arm/common/bL_platsmp.c        | 1 +
>>>>>     arch/arm/common/gic.c               | 6 ++++++
>>>>>     arch/arm/include/asm/hardware/gic.h | 2 ++
>>>>>     3 files changed, 9 insertions(+)
>>>>>
>>>>> diff --git a/arch/arm/common/bL_platsmp.c b/arch/arm/common/bL_platsmp.c
>>>>> index 0ae44123bf..6a3b251b97 100644
>>>>> --- a/arch/arm/common/bL_platsmp.c
>>>>> +++ b/arch/arm/common/bL_platsmp.c
>>>>> @@ -68,6 +68,7 @@ static void __ref bL_cpu_die(unsigned int cpu)
>>>>>     	pcpu = mpidr & 0xff;
>>>>>     	pcluster = (mpidr >> 8) & 0xff;
>>>>>     	bL_set_entry_vector(pcpu, pcluster, NULL);
>>>>> +	gic_cpu_if_down();
>>>>
>>>> So for a case where CPU still don't power down for some reason even
>>>> after CPU interface is disabled, can not listen to and SGI or PPI.
>>>> Not sure if this happens on big.LITTLE but i have seen one such issue
>>>> on Cortex-A9 based SOC.
>>>
>>> Here the problem was the reverse i.e. a CPU wouldn't go down because
>>> some pending SGIs prevented that.
>>>
>> I understood that part. What I was saying is, with CPU IF disabled and
>> if CPU doesn't enter into the intended low power state and if the wakeup
>> mechanism on that CPU is SGI/SPI, CPU may never wakeup and can lead to
>> dead lock. I have seen this scenario on OMAP especially in CPUidle path.
>
> Obviously, on the CPU idle path, you should not turn off the GIC
> interface as this might lose the ability to wake the CPU up with a
> pending interrupt, if your system is so configured.
>
> Here this is the CPU hot unplug path and we don't want the CPU to be
> awaken at all until we explicitly do something to wake it back up.
>
I see.

> However, in theory, all interrupts should have been migrated away from
> this CPU, so there shouldn't be any need for this.  I should revisit the
> test that led me to create this patch.
>
Thats right from hot-plug path and SPI are concerned. But SGI/PPI can
still wakeup CPU and there is no migration as such since they are local
to that

>> It may not be relevant for switcher considering, you almost force CPU to
>> enter to low power state :-)
>
> The switcher doesn't use cpu_die() but calls into bL_cpu_power_down()
> directly.
>
Good to know that.

Regards,
Santosh