[PATCH 12/14] ARM: OMAP2+: omap4panda: Adapt HUB power to regulator framework

[Roger Quadros]

We model the HUB_POWER GPIO as a fixed regulator device. This regulator
is then used as "vcc" supply for the USB PHY device and is managed
by the PHY driver.

Signed-off-by: Roger Quadros <rogerq at ti.com>
---
 arch/arm/mach-omap2/board-omap4panda.c |   38 +++++++++++++++++++++++++++----
 1 files changed, 33 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 350c4db..a4831cc 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -132,12 +132,45 @@ static struct platform_device btwilink_device = {
 	.id	= -1,
 };
 
+/* Regulator for USB HUB supply */
+static struct regulator_consumer_supply hub_power_supplies[] = {
+/* Link PHY device to USB HUB supply so it gets enabled in the PHY driver */
+	REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.0"),
+};
+
+static struct regulator_init_data hub_power_data = {
+	.constraints = {
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+	.consumer_supplies	= hub_power_supplies,
+	.num_consumer_supplies	= ARRAY_SIZE(hub_power_supplies),
+};
+
+static struct fixed_voltage_config hub_power_config = {
+	.supply_name    = "vhub",
+	.microvolts = 3300000,
+	.gpio = GPIO_HUB_POWER,
+	.startup_delay = 70000, /* 70msec */
+	.enable_high = 1,
+	.enabled_at_boot = 0,
+	.init_data = &hub_power_data,
+};
+
+static struct platform_device hub_power_device = {
+	.name	= "reg-fixed-voltage",
+	.id	= 2,
+	.dev = {
+		.platform_data = &hub_power_config,
+	},
+};
+
 static struct platform_device *panda_devices[] __initdata = {
 	&leds_gpio,
 	&wl1271_device,
 	&panda_abe_audio,
 	&panda_hdmi_audio_codec,
 	&btwilink_device,
+	&hub_power_device,
 };
 
 static struct nop_usb_xceiv_platform_data phy_pdata0 = {
@@ -164,7 +197,6 @@ static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 };
 
 static struct gpio panda_ehci_gpios[] __initdata = {
-	{ GPIO_HUB_POWER,	GPIOF_OUT_INIT_LOW,  "hub_power"  },
 	{ GPIO_HUB_NRESET,	GPIOF_OUT_INIT_LOW,  "hub_nreset" },
 };
 
@@ -180,7 +212,6 @@ static void __init omap4_ehci_init(void)
 		return;
 	}
 
-	gpio_export(GPIO_HUB_POWER, 0);
 	gpio_export(GPIO_HUB_NRESET, 0);
 	gpio_set_value(GPIO_HUB_NRESET, 1);
 
@@ -190,9 +221,6 @@ static void __init omap4_ehci_init(void)
 		pr_err("Failed to add main_clk alias to auxclk3_ck\n");
 
 	usbhs_init(&usbhs_bdata);
-
-	/* enable power to hub */
-	gpio_set_value(GPIO_HUB_POWER, 1);
 }
 
 static struct omap_musb_board_data musb_board_data = {
-- 
1.7.4.1