[PATCH 8/9] [HACK] ARM: imx: work around v7_cpu_resume link error

[Shawn Guo]

On Mon, Feb 18, 2013 at 12:06:32PM -0500, Nicolas Pitre wrote:
> Try the following instead.  It makes the code simpler and easier to 
> debug.
> 
It works now.  Thanks, Nico.  Care to send a patch for it?  I'd like
to apply it.

Shawn

> diff --git a/arch/arm/mach-imx/headsmp.S b/arch/arm/mach-imx/headsmp.S
> index 7e49deb128..27bc06e910 100644
> --- a/arch/arm/mach-imx/headsmp.S
> +++ b/arch/arm/mach-imx/headsmp.S
> @@ -73,16 +73,16 @@ ENDPROC(v7_secondary_startup)
>  
>  #ifdef CONFIG_PM
>  /*
> - * The following code is located into the .data section.  This is to
> - * allow phys_l2x0_saved_regs to be accessed with a relative load
> - * as we are running on physical address here.
> + * The following code must assume it is running from physical address
> + * where absolute virtual addresses to the data section have to be
> + * turned into relative ones.
>   */
> -	.data
> -	.align
>  
>  #ifdef CONFIG_CACHE_L2X0
>  	.macro	pl310_resume
> -	ldr	r2, phys_l2x0_saved_regs
> +	adr	r0, l2x0_saved_regs_offset
> +	ldr	r2, [r0]
> +	add	r2, r2, r0
>  	ldr	r0, [r2, #L2X0_R_PHY_BASE]	@ get physical base of l2x0
>  	ldr	r1, [r2, #L2X0_R_AUX_CTRL]	@ get aux_ctrl value
>  	str	r1, [r0, #L2X0_AUX_CTRL]	@ restore aux_ctrl
> @@ -90,9 +90,9 @@ ENDPROC(v7_secondary_startup)
>  	str	r1, [r0, #L2X0_CTRL]		@ re-enable L2
>  	.endm
>  
> -	.globl	phys_l2x0_saved_regs
> -phys_l2x0_saved_regs:
> -        .long   0
> +l2x0_saved_regs_offset:
> +	.word	l2x0_saved_regs - .
> +
>  #else
>  	.macro	pl310_resume
>  	.endm
> diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c
> index f7b0c2b1b9..f3791f980d 100644
> --- a/arch/arm/mach-imx/pm-imx6q.c
> +++ b/arch/arm/mach-imx/pm-imx6q.c
> @@ -21,8 +21,6 @@
>  #include <mach/common.h>
>  #include <mach/hardware.h>
>  
> -extern unsigned long phys_l2x0_saved_regs;
> -
>  static int imx6q_suspend_finish(unsigned long val)
>  {
>  	cpu_do_idle();
> @@ -55,18 +53,5 @@ static const struct platform_suspend_ops imx6q_pm_ops = {
>  
>  void __init imx6q_pm_init(void)
>  {
> -	/*
> -	 * The l2x0 core code provides an infrastucture to save and restore
> -	 * l2x0 registers across suspend/resume cycle.  But because imx6q
> -	 * retains L2 content during suspend and needs to resume L2 before
> -	 * MMU is enabled, it can only utilize register saving support and
> -	 * have to take care of restoring on its own.  So we save physical
> -	 * address of the data structure used by l2x0 core to save registers,
> -	 * and later restore the necessary ones in imx6q resume entry.
> -	 */
> -#ifdef CONFIG_CACHE_L2X0
> -	phys_l2x0_saved_regs = __pa(&l2x0_saved_regs);
> -#endif
> -
>  	suspend_set_ops(&imx6q_pm_ops);
>  }
> 
> Nicolas