[PATCH 1/4] spi: s3c64xx: modified error interrupt handling and init

[Girish KS]

On Thu, Feb 7, 2013 at 5:04 PM, Girish KS <girishks2000 at gmail.com> wrote:
> On Wed, Feb 6, 2013 at 3:48 PM, Grant Likely <grant.likely at secretlab.ca> wrote:
>> On Wed, Feb 6, 2013 at 8:12 PM, Girish KS <girishks2000 at gmail.com> wrote:
>>> On Wed, Feb 6, 2013 at 2:26 AM, Grant Likely <grant.likely at secretlab.ca> wrote:
>>>> On Tue,  5 Feb 2013 15:09:41 -0800, Girish K S <girishks2000 at gmail.com> wrote:
>>>>> The status of the interrupt is available in the status register,
>>>>> so reading the clear pending register and writing back the same
>>>>> value will not actually clear the pending interrupts. This patch
>>>>> modifies the interrupt handler to read the status register and
>>>>> clear the corresponding pending bit in the clear pending register.
>>>>>
>>>>> Modified the hwInit function to clear all the pending interrupts.
>>>>>
>>>>> Signed-off-by: Girish K S <ks.giri at samsung.com>
>>>>> ---
>>>>>  drivers/spi/spi-s3c64xx.c |   41 +++++++++++++++++++++++++----------------
>>>>>  1 file changed, 25 insertions(+), 16 deletions(-)
>>>>>
>>>>> diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c
>>>>> index ad93231..b770f88 100644
>>>>> --- a/drivers/spi/spi-s3c64xx.c
>>>>> +++ b/drivers/spi/spi-s3c64xx.c
>>>>> @@ -997,25 +997,30 @@ static irqreturn_t s3c64xx_spi_irq(int irq, void *data)
>>>>>  {
>>>>>       struct s3c64xx_spi_driver_data *sdd = data;
>>>>>       struct spi_master *spi = sdd->master;
>>>>> -     unsigned int val;
>>>>> +     unsigned int val, clr = 0;
>>>>>
>>>>> -     val = readl(sdd->regs + S3C64XX_SPI_PENDING_CLR);
>>>>> +     val = readl(sdd->regs + S3C64XX_SPI_STATUS);
>>>>>
>>>>> -     val &= S3C64XX_SPI_PND_RX_OVERRUN_CLR |
>>>>> -             S3C64XX_SPI_PND_RX_UNDERRUN_CLR |
>>>>> -             S3C64XX_SPI_PND_TX_OVERRUN_CLR |
>>>>> -             S3C64XX_SPI_PND_TX_UNDERRUN_CLR;
>>>>> -
>>>>> -     writel(val, sdd->regs + S3C64XX_SPI_PENDING_CLR);
>>>>> -
>>>>> -     if (val & S3C64XX_SPI_PND_RX_OVERRUN_CLR)
>>>>> +     if (val & S3C64XX_SPI_ST_RX_OVERRUN_ERR) {
>>>>> +             clr = S3C64XX_SPI_PND_RX_OVERRUN_CLR;
>>>>>               dev_err(&spi->dev, "RX overrun\n");
>>>>> -     if (val & S3C64XX_SPI_PND_RX_UNDERRUN_CLR)
>>>>> +     }
>>>>> +     if (val & S3C64XX_SPI_ST_RX_UNDERRUN_ERR) {
>>>>> +             clr |= S3C64XX_SPI_PND_RX_UNDERRUN_CLR;
>>>>>               dev_err(&spi->dev, "RX underrun\n");
>>>>> -     if (val & S3C64XX_SPI_PND_TX_OVERRUN_CLR)
>>>>> +     }
>>>>> +     if (val & S3C64XX_SPI_ST_TX_OVERRUN_ERR) {
>>>>> +             clr |= S3C64XX_SPI_PND_TX_OVERRUN_CLR;
>>>>>               dev_err(&spi->dev, "TX overrun\n");
>>>>> -     if (val & S3C64XX_SPI_PND_TX_UNDERRUN_CLR)
>>>>> +     }
>>>>> +     if (val & S3C64XX_SPI_ST_TX_UNDERRUN_ERR) {
>>>>> +             clr |= S3C64XX_SPI_PND_TX_UNDERRUN_CLR;
>>>>>               dev_err(&spi->dev, "TX underrun\n");
>>>>> +     }
>>>>> +
>>>>> +     /* Clear the pending irq by setting and then clearing it */
>>>>> +     writel(clr, sdd->regs + S3C64XX_SPI_PENDING_CLR);
>>>>> +     writel(clr & ~clr, sdd->regs + S3C64XX_SPI_PENDING_CLR);
>>>>
>>>> Wait, what?  clr & ~clr == 0   Always.  What are you actually trying to do here?
>>> The user manual says, wirting 1 to the pending clear register clears
>>> the interrupt (its not auto clear to 0). so i need to explicitly reset
>>> those bits thats what the 2nd write does
>>
>> Then write 0. That's the result of what the code does anyway, but the
>> code as-written is nonsensical.
> i cannot write 0. because the 0th bit is trailing byte interrupt clear
> pending bit, which is not being handled in the handler.

Sorry, Writing 0  will still be valid after code for trainling byte is added..
will change and resubmit

>>
>> g.