[PATCH 3/8] ARM: dts: omap: Add usb_otg and glue data

[Rajendra Nayak]

[]...

>
> diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
> index 29a043e..4688265 100644
> --- a/Documentation/devicetree/bindings/usb/omap-usb.txt
> +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
> @@ -15,6 +15,7 @@ OMAP MUSB GLUE
>      represents PERIPHERAL.
>    - power : Should be "50". This signifies the controller can supply upto
>      100mA when operating in host mode.
> + - usb-phy : the phandle for the PHY device
>
>   SOC specific device node entry
>   usb_otg_hs: usb_otg_hs at 4a0ab000 {
> diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
> index 3705a81..cb07583 100644
> --- a/arch/arm/boot/dts/omap3-beagle-xm.dts
> +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
> @@ -107,3 +107,9 @@
>   	 */
>   	ti,pulldowns = <0x03a1c4>;
>   };
> +
> +&usb_otg_hs {
> +	interface_type = <0>;
> +	mode = <3>;
> +	power = <50>;
> +};
> diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts
> index e8ba1c2..afb9ba9 100644
> --- a/arch/arm/boot/dts/omap3-evm.dts
> +++ b/arch/arm/boot/dts/omap3-evm.dts
> @@ -59,3 +59,9 @@
>   &twl_gpio {
>   	ti,use-leds;
>   };
> +
> +&usb_otg_hs {
> +	interface_type = <0>;
> +	mode = <3>;
> +	power = <50>;
> +};
> diff --git a/arch/arm/boot/dts/omap3-overo.dtsi b/arch/arm/boot/dts/omap3-overo.dtsi
> index 89808ce..4b3d157 100644
> --- a/arch/arm/boot/dts/omap3-overo.dtsi
> +++ b/arch/arm/boot/dts/omap3-overo.dtsi
> @@ -55,3 +55,9 @@
>   &twl_gpio {
>   	ti,use-leds;
>   };
> +
> +&usb_otg_hs {
> +	interface_type = <0>;
> +	mode = <3>;
> +	power = <50>;
> +};
> diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
> index 1acc261..b6472f7 100644
> --- a/arch/arm/boot/dts/omap3.dtsi
> +++ b/arch/arm/boot/dts/omap3.dtsi
> @@ -397,5 +397,17 @@
>   			ti,timer-alwon;
>   			ti,timer-secure;
>   		};
> +
> +		usb_otg_hs: usb_otg_hs at 480ab000 {
> +			compatible = "ti,omap3-musb";
> +			reg = <0x480ab000 0x1000>;
> +			interrupts = <0 92 0x4>, <0 93 0x4>;
> +			interrupt-names = "mc", "dma";
> +			ti,hwmods = "usb_otg_hs";
> +			usb-phy = <&usb2_phy>;
> +			multipoint = <1>;
> +			num_eps = <16>;
> +			ram_bits = <12>;

Where are these bindings documented? The general convention is to use
a '-' for property names and not '_'

> +		};
>   	};
>   };
> diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts
> index 4122efe..612c9bb 100644
> --- a/arch/arm/boot/dts/omap4-panda.dts
> +++ b/arch/arm/boot/dts/omap4-panda.dts
> @@ -206,3 +206,9 @@
>   &twl_usb_comparator {
>   	usb-supply = <&vusb>;
>   };
> +
> +&usb_otg_hs {
> +	interface_type = <1>;
> +	mode = <3>;
> +	power = <50>;
> +};
> diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
> index 43e5258..582d7ee 100644
> --- a/arch/arm/boot/dts/omap4-sdp.dts
> +++ b/arch/arm/boot/dts/omap4-sdp.dts
> @@ -428,3 +428,9 @@
>   &twl_usb_comparator {
>   	usb-supply = <&vusb>;
>   };
> +
> +&usb_otg_hs {
> +	interface_type = <1>;
> +	mode = <3>;
> +	power = <50>;
> +};
> diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
> index c829d7e..5171739 100644
> --- a/arch/arm/boot/dts/omap4.dtsi
> +++ b/arch/arm/boot/dts/omap4.dtsi
> @@ -542,5 +542,18 @@
>   			reg-names = "control_dev_conf", "otghs_control";
>   			ti,type = <1>;
>   		};
> +
> +		usb_otg_hs: usb_otg_hs at 4a0ab000 {
> +			compatible = "ti,omap4-musb";
> +			reg = <0x4a0ab000 0x7ff>;
> +			interrupts = <0 92 0x4>, <0 93 0x4>;
> +			interrupt-names = "mc", "dma";
> +			ti,hwmods = "usb_otg_hs";
> +			usb-phy = <&usb2_phy>;
> +			multipoint = <1>;
> +			num_eps = <16>;
> +			ram_bits = <12>;
> +			ti,has-mailbox;
> +		};
>   	};
>   };
> diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi
> index ed0bc95..398d2c3 100644
> --- a/arch/arm/boot/dts/twl4030.dtsi
> +++ b/arch/arm/boot/dts/twl4030.dtsi
> @@ -67,7 +67,7 @@
>   		#interrupt-cells = <1>;
>   	};
>
> -	twl4030-usb {
> +	usb2_phy: twl4030-usb {
>   		compatible = "ti,twl4030-usb";
>   		interrupts = <10>, <4>;
>   		usb1v5-supply = <&vusb1v5>;
>