[PATCH 2/4] spi: s3c64xx: added support for polling mode
Girish K S
girishks2000 at gmail.com
Tue Feb 5 18:09:42 EST 2013
The 64xx spi driver supports partial polling mode.
Only the last chunk of the transfer length is transferred
or recieved in polling mode.
Some SoC's that adopt this controller might not have have dma
interface. This patch adds support for complete polling mode
and gives flexibity for the user to select poll/dma mode.
Signed-off-by: Girish K S <ks.giri at samsung.com>
---
drivers/spi/spi-s3c64xx.c | 65 +++++++++++++++++++++------------------------
1 file changed, 30 insertions(+), 35 deletions(-)
diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c
index b770f88..90770bd 100644
--- a/drivers/spi/spi-s3c64xx.c
+++ b/drivers/spi/spi-s3c64xx.c
@@ -35,6 +35,7 @@
#include <linux/platform_data/spi-s3c64xx.h>
#define MAX_SPI_PORTS 3
+#define S3C64XX_SPI_QUIRK_POLL (1 << 0)
/* Registers and bit-fields */
@@ -126,6 +127,7 @@
#define S3C64XX_SPI_TRAILCNT S3C64XX_SPI_MAX_TRAILCNT
#define msecs_to_loops(t) (loops_per_jiffy / 1000 * HZ * t)
+#define is_polling(x) (x->port_conf->quirks & S3C64XX_SPI_QUIRK_POLL)
#define RXBUSY (1<<2)
#define TXBUSY (1<<3)
@@ -155,6 +157,7 @@ struct s3c64xx_spi_port_config {
int fifo_lvl_mask[MAX_SPI_PORTS];
int rx_lvl_offset;
int tx_st_done;
+ int quirks;
bool high_speed;
bool clk_from_cmu;
};
@@ -345,19 +348,7 @@ static void enable_datapath(struct s3c64xx_spi_driver_data *sdd,
chcfg = readl(regs + S3C64XX_SPI_CH_CFG);
chcfg &= ~S3C64XX_SPI_CH_TXCH_ON;
-
- if (dma_mode) {
chcfg &= ~S3C64XX_SPI_CH_RXCH_ON;
- } else {
- /* Always shift in data in FIFO, even if xfer is Tx only,
- * this helps setting PCKT_CNT value for generating clocks
- * as exactly needed.
- */
- chcfg |= S3C64XX_SPI_CH_RXCH_ON;
- writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
- | S3C64XX_SPI_PACKET_CNT_EN,
- regs + S3C64XX_SPI_PACKET_CNT);
- }
if (xfer->tx_buf != NULL) {
sdd->state |= TXBUSY;
@@ -385,6 +376,10 @@ static void enable_datapath(struct s3c64xx_spi_driver_data *sdd,
if (xfer->rx_buf != NULL) {
sdd->state |= RXBUSY;
+ chcfg |= S3C64XX_SPI_CH_RXCH_ON;
+ writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
+ | S3C64XX_SPI_PACKET_CNT_EN,
+ regs + S3C64XX_SPI_PACKET_CNT);
if (sdd->port_conf->high_speed && sdd->cur_speed >= 30000000UL
&& !(sdd->cur_mode & SPI_CPHA))
@@ -392,10 +387,6 @@ static void enable_datapath(struct s3c64xx_spi_driver_data *sdd,
if (dma_mode) {
modecfg |= S3C64XX_SPI_MODE_RXDMA_ON;
- chcfg |= S3C64XX_SPI_CH_RXCH_ON;
- writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
- | S3C64XX_SPI_PACKET_CNT_EN,
- regs + S3C64XX_SPI_PACKET_CNT);
prepare_dma(&sdd->rx_dma, xfer->len, xfer->rx_dma);
}
}
@@ -421,6 +412,9 @@ static inline void enable_cs(struct s3c64xx_spi_driver_data *sdd,
cs = spi->controller_data;
gpio_set_value(cs->line, spi->mode & SPI_CS_HIGH ? 1 : 0);
+
+ /* Start the signals */
+ writel(0, sdd->regs + S3C64XX_SPI_SLAVE_SEL);
}
static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd,
@@ -445,12 +439,12 @@ static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd,
} while (RX_FIFO_LVL(status, sdd) < xfer->len && --val);
}
- if (!val)
- return -EIO;
-
if (dma_mode) {
u32 status;
+ if (!val)
+ return -EIO;
+
/*
* DmaTx returns after simply writing data in the FIFO,
* w/o waiting for real transmission on the bus to finish.
@@ -480,16 +474,19 @@ static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd,
switch (sdd->cur_bpw) {
case 32:
- ioread32_rep(regs + S3C64XX_SPI_RX_DATA,
- xfer->rx_buf, xfer->len / 4);
+ for (val = 0; val < (xfer->len / 4); val++)
+ *((u32 *)xfer->rx_buf + val) =
+ ioread32(regs + S3C64XX_SPI_RX_DATA);
break;
case 16:
- ioread16_rep(regs + S3C64XX_SPI_RX_DATA,
- xfer->rx_buf, xfer->len / 2);
+ for (val = 0; val < (xfer->len / 2); val++)
+ *((u16 *)xfer->rx_buf + val) =
+ ioread16(regs + S3C64XX_SPI_RX_DATA);
break;
default:
- ioread8_rep(regs + S3C64XX_SPI_RX_DATA,
- xfer->rx_buf, xfer->len);
+ for (val = 0; val < xfer->len; val++)
+ *((u8 *)xfer->rx_buf + val) =
+ ioread8(regs + S3C64XX_SPI_RX_DATA);
break;
}
sdd->state &= ~RXBUSY;
@@ -507,6 +504,10 @@ static inline void disable_cs(struct s3c64xx_spi_driver_data *sdd,
sdd->tgl_spi = NULL;
gpio_set_value(cs->line, spi->mode & SPI_CS_HIGH ? 0 : 1);
+
+ /* Quiese the signals */
+ writel(S3C64XX_SPI_SLAVE_SIG_INACT,
+ sdd->regs + S3C64XX_SPI_SLAVE_SEL);
}
static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
@@ -588,7 +589,7 @@ static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd,
struct device *dev = &sdd->pdev->dev;
struct spi_transfer *xfer;
- if (msg->is_dma_mapped)
+ if (is_polling(sdd) || msg->is_dma_mapped)
return 0;
/* First mark all xfer unmapped */
@@ -637,7 +638,7 @@ static void s3c64xx_spi_unmap_mssg(struct s3c64xx_spi_driver_data *sdd,
struct device *dev = &sdd->pdev->dev;
struct spi_transfer *xfer;
- if (msg->is_dma_mapped)
+ if (is_polling(sdd) || msg->is_dma_mapped)
return;
list_for_each_entry(xfer, &msg->transfers, transfer_list) {
@@ -715,7 +716,8 @@ static int s3c64xx_spi_transfer_one_message(struct spi_master *master,
}
/* Polling method for xfers not bigger than FIFO capacity */
- if (xfer->len <= ((FIFO_LVL_MASK(sdd) >> 1) + 1))
+ if (is_polling(sdd) ||
+ xfer->len <= ((FIFO_LVL_MASK(sdd) >> 1) + 1))
use_dma = 0;
else
use_dma = 1;
@@ -731,17 +733,10 @@ static int s3c64xx_spi_transfer_one_message(struct spi_master *master,
/* Slave Select */
enable_cs(sdd, spi);
- /* Start the signals */
- writel(0, sdd->regs + S3C64XX_SPI_SLAVE_SEL);
-
spin_unlock_irqrestore(&sdd->lock, flags);
status = wait_for_xfer(sdd, xfer, use_dma);
- /* Quiese the signals */
- writel(S3C64XX_SPI_SLAVE_SIG_INACT,
- sdd->regs + S3C64XX_SPI_SLAVE_SEL);
-
if (status) {
dev_err(&spi->dev, "I/O Error: "
"rx-%d tx-%d res:rx-%c tx-%c len-%d\n",
--
1.7.10.4
More information about the linux-arm-kernel
mailing list