[PATCH v8 01/12] gpio: add gpio offset in gpio range cells property

[Tony Lindgren]

* Haojian Zhuang <haojian.zhuang at linaro.org> [130202 09:29]:
> Add gpio offset into "gpio-range-cells" property. It's used to support
> sparse pinctrl range in gpio chip.
> 
> Signed-off-by: Haojian Zhuang <haojian.zhuang at linaro.org>
> ---
>  Documentation/devicetree/bindings/gpio/gpio.txt |    6 +++---
>  arch/arm/boot/dts/spear1310.dtsi                |    4 ++--
>  arch/arm/boot/dts/spear1340.dtsi                |    4 ++--
>  arch/arm/boot/dts/spear310.dtsi                 |    4 ++--
>  arch/arm/boot/dts/spear320.dtsi                 |    4 ++--
>  drivers/gpio/gpiolib-of.c                       |   15 ++-------------
>  6 files changed, 13 insertions(+), 24 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt
> index a336287..d933af3 100644
> --- a/Documentation/devicetree/bindings/gpio/gpio.txt
> +++ b/Documentation/devicetree/bindings/gpio/gpio.txt
> @@ -98,7 +98,7 @@ announce the pinrange to the pin ctrl subsystem. For example,
>  		compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
>  		reg = <0x1460 0x18>;
>  		gpio-controller;
> -		gpio-ranges = <&pinctrl1 20 10>, <&pinctrl2 50 20>;
> +		gpio-ranges = <&pinctrl1 0 20 10>, <&pinctrl2 10 50 20>;
>  
>      }
>  
> @@ -107,8 +107,8 @@ where,
>  
>     Next values specify the base pin and number of pins for the range
>     handled by 'qe_pio_e' gpio. In the given example from base pin 20 to
> -   pin 29 under pinctrl1 and pin 50 to pin 69 under pinctrl2 is handled
> -   by this gpio controller.
> +   pin 29 under pinctrl1 with gpio offset 0 and pin 50 to pin 69 under
> +   pinctrl2 with gpio offset 10 is handled by this gpio controller.
>  
>  The pinctrl node must have "#gpio-range-cells" property to show number of
>  arguments to pass with phandle from gpio controllers node.
> diff --git a/arch/arm/boot/dts/spear1310.dtsi b/arch/arm/boot/dts/spear1310.dtsi
> index 1513c19..122ae94 100644
> --- a/arch/arm/boot/dts/spear1310.dtsi
> +++ b/arch/arm/boot/dts/spear1310.dtsi
> @@ -89,7 +89,7 @@
>  		pinmux: pinmux at e0700000 {
>  			compatible = "st,spear1310-pinmux";
>  			reg = <0xe0700000 0x1000>;
> -			#gpio-range-cells = <2>;
> +			#gpio-range-cells = <3>;
>  		};
>  
>  		apb {

Hmm is this safe to do if there are bootloaders using the old binding?
Maybe we should support both #gpio-range-cells = <2> and <3> bindings
instead?

Regards,

Tony