[PATCH v6] cpufreq: add imx6q-cpufreq driver

Rafael J. Wysocki rjw at sisk.pl
Mon Feb 4 07:19:25 EST 2013


On Monday, February 04, 2013 01:46:29 PM Shawn Guo wrote:
> Add an imx6q-cpufreq driver for Freescale i.MX6Q SoC to handle the
> hardware specific frequency and voltage scaling requirements.
> 
> The driver supports module build and is instantiated by the platform
> device/driver mechanism, so that it will not be instantiated on other
> platforms, as IMX is built with multiplatform support.

Am I supposed to take it this time? :-)

Rafael


> Signed-off-by: Shawn Guo <shawn.guo at linaro.org>
> Reviewed-by: Viresh Kumar <viresh.kumar at linaro.org>
> ---
> Changes since v5:
>  * Update clock tranistion code to make keep use count correct
> 
>  drivers/cpufreq/Kconfig.arm     |    9 ++
>  drivers/cpufreq/Makefile        |    1 +
>  drivers/cpufreq/imx6q-cpufreq.c |  336 +++++++++++++++++++++++++++++++++++++++
>  3 files changed, 346 insertions(+)
>  create mode 100644 drivers/cpufreq/imx6q-cpufreq.c
> 
> diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
> index ffe55b8..c65226c 100644
> --- a/drivers/cpufreq/Kconfig.arm
> +++ b/drivers/cpufreq/Kconfig.arm
> @@ -77,6 +77,15 @@ config ARM_EXYNOS5250_CPUFREQ
>  	  This adds the CPUFreq driver for Samsung EXYNOS5250
>  	  SoC.
>  
> +config ARM_IMX6Q_CPUFREQ
> +	tristate "Freescale i.MX6Q cpufreq support"
> +	depends on SOC_IMX6Q
> +	depends on REGULATOR_ANATOP
> +	help
> +	  This adds cpufreq driver support for Freescale i.MX6Q SOC.
> +
> +	  If in doubt, say N.
> +
>  config ARM_SPEAR_CPUFREQ
>  	bool "SPEAr CPUFreq support"
>  	depends on PLAT_SPEAR
> diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
> index e2a5da7..93610b2 100644
> --- a/drivers/cpufreq/Makefile
> +++ b/drivers/cpufreq/Makefile
> @@ -54,6 +54,7 @@ obj-$(CONFIG_ARM_EXYNOS5250_CPUFREQ)	+= exynos5250-cpufreq.o
>  obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ)	+= omap-cpufreq.o
>  obj-$(CONFIG_ARM_SPEAR_CPUFREQ)		+= spear-cpufreq.o
>  obj-$(CONFIG_ARM_HIGHBANK_CPUFREQ)	+= highbank-cpufreq.o
> +obj-$(CONFIG_ARM_IMX6Q_CPUFREQ)		+= imx6q-cpufreq.o
>  
>  ##################################################################################
>  # PowerPC platform drivers
> diff --git a/drivers/cpufreq/imx6q-cpufreq.c b/drivers/cpufreq/imx6q-cpufreq.c
> new file mode 100644
> index 0000000..d6b6ef3
> --- /dev/null
> +++ b/drivers/cpufreq/imx6q-cpufreq.c
> @@ -0,0 +1,336 @@
> +/*
> + * Copyright (C) 2013 Freescale Semiconductor, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/cpufreq.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/opp.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +
> +#define PU_SOC_VOLTAGE_NORMAL	1250000
> +#define PU_SOC_VOLTAGE_HIGH	1275000
> +#define FREQ_1P2_GHZ		1200000000
> +
> +static struct regulator *arm_reg;
> +static struct regulator *pu_reg;
> +static struct regulator *soc_reg;
> +
> +static struct clk *arm_clk;
> +static struct clk *pll1_sys_clk;
> +static struct clk *pll1_sw_clk;
> +static struct clk *step_clk;
> +static struct clk *pll2_pfd2_396m_clk;
> +
> +static struct device *cpu_dev;
> +static struct cpufreq_frequency_table *freq_table;
> +static unsigned int transition_latency;
> +
> +static int imx6q_verify_speed(struct cpufreq_policy *policy)
> +{
> +	return cpufreq_frequency_table_verify(policy, freq_table);
> +}
> +
> +static unsigned int imx6q_get_speed(unsigned int cpu)
> +{
> +	return clk_get_rate(arm_clk) / 1000;
> +}
> +
> +static int imx6q_set_target(struct cpufreq_policy *policy,
> +			    unsigned int target_freq, unsigned int relation)
> +{
> +	struct cpufreq_freqs freqs;
> +	struct opp *opp;
> +	unsigned long freq_hz, volt, volt_old;
> +	unsigned int index, cpu;
> +	int ret;
> +
> +	ret = cpufreq_frequency_table_target(policy, freq_table, target_freq,
> +					     relation, &index);
> +	if (ret) {
> +		dev_err(cpu_dev, "failed to match target frequency %d: %d\n",
> +			target_freq, ret);
> +		return ret;
> +	}
> +
> +	freqs.new = freq_table[index].frequency;
> +	freq_hz = freqs.new * 1000;
> +	freqs.old = clk_get_rate(arm_clk) / 1000;
> +
> +	if (freqs.old == freqs.new)
> +		return 0;
> +
> +	for_each_online_cpu(cpu) {
> +		freqs.cpu = cpu;
> +		cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
> +	}
> +
> +	rcu_read_lock();
> +	opp = opp_find_freq_ceil(cpu_dev, &freq_hz);
> +	if (IS_ERR(opp)) {
> +		rcu_read_unlock();
> +		dev_err(cpu_dev, "failed to find OPP for %ld\n", freq_hz);
> +		return PTR_ERR(opp);
> +	}
> +
> +	volt = opp_get_voltage(opp);
> +	rcu_read_unlock();
> +	volt_old = regulator_get_voltage(arm_reg);
> +
> +	dev_dbg(cpu_dev, "%u MHz, %ld mV --> %u MHz, %ld mV\n",
> +		freqs.old / 1000, volt_old / 1000,
> +		freqs.new / 1000, volt / 1000);
> +
> +	/* scaling up?  scale voltage before frequency */
> +	if (freqs.new > freqs.old) {
> +		ret = regulator_set_voltage_tol(arm_reg, volt, 0);
> +		if (ret) {
> +			dev_err(cpu_dev,
> +				"failed to scale vddarm up: %d\n", ret);
> +			return ret;
> +		}
> +
> +		/*
> +		 * Need to increase vddpu and vddsoc for safety
> +		 * if we are about to run at 1.2 GHz.
> +		 */
> +		if (freqs.new == FREQ_1P2_GHZ / 1000) {
> +			regulator_set_voltage_tol(pu_reg,
> +					PU_SOC_VOLTAGE_HIGH, 0);
> +			regulator_set_voltage_tol(soc_reg,
> +					PU_SOC_VOLTAGE_HIGH, 0);
> +		}
> +	}
> +
> +	/*
> +	 * The setpoints are selected per PLL/PDF frequencies, so we need to
> +	 * reprogram PLL for frequency scaling.  The procedure of reprogramming
> +	 * PLL1 is as below.
> +	 *
> +	 *  - Enable pll2_pfd2_396m_clk and reparent pll1_sw_clk to it
> +	 *  - Reprogram pll1_sys_clk and reparent pll1_sw_clk back to it
> +	 *  - Disable pll2_pfd2_396m_clk
> +	 */
> +	clk_prepare_enable(pll2_pfd2_396m_clk);
> +	clk_set_parent(step_clk, pll2_pfd2_396m_clk);
> +	clk_set_parent(pll1_sw_clk, step_clk);
> +	if (freq_hz > clk_get_rate(pll2_pfd2_396m_clk)) {
> +		clk_set_rate(pll1_sys_clk, freqs.new * 1000);
> +		/*
> +		 * If we are leaving 396 MHz set-point, we need to enable
> +		 * pll1_sys_clk and disable pll2_pfd2_396m_clk to keep
> +		 * their use count correct.
> +		 */
> +		if (freqs.old * 1000 <= clk_get_rate(pll2_pfd2_396m_clk)) {
> +			clk_prepare_enable(pll1_sys_clk);
> +			clk_disable_unprepare(pll2_pfd2_396m_clk);
> +		}
> +		clk_set_parent(pll1_sw_clk, pll1_sys_clk);
> +		clk_disable_unprepare(pll2_pfd2_396m_clk);
> +	} else {
> +		/*
> +		 * Disable pll1_sys_clk if pll2_pfd2_396m_clk is sufficient
> +		 * to provide the frequency.
> +		 */
> +		clk_disable_unprepare(pll1_sys_clk);
> +	}
> +
> +	/* Ensure the arm clock divider is what we expect */
> +	ret = clk_set_rate(arm_clk, freqs.new * 1000);
> +	if (ret) {
> +		dev_err(cpu_dev, "failed to set clock rate: %d\n", ret);
> +		regulator_set_voltage_tol(arm_reg, volt_old, 0);
> +		return ret;
> +	}
> +
> +	/* scaling down?  scale voltage after frequency */
> +	if (freqs.new < freqs.old) {
> +		ret = regulator_set_voltage_tol(arm_reg, volt, 0);
> +		if (ret)
> +			dev_warn(cpu_dev,
> +				 "failed to scale vddarm down: %d\n", ret);
> +
> +		if (freqs.old == FREQ_1P2_GHZ / 1000) {
> +			regulator_set_voltage_tol(pu_reg,
> +					PU_SOC_VOLTAGE_NORMAL, 0);
> +			regulator_set_voltage_tol(soc_reg,
> +					PU_SOC_VOLTAGE_NORMAL, 0);
> +		}
> +	}
> +
> +	for_each_online_cpu(cpu) {
> +		freqs.cpu = cpu;
> +		cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
> +	}
> +
> +	return 0;
> +}
> +
> +static int imx6q_cpufreq_init(struct cpufreq_policy *policy)
> +{
> +	int ret;
> +
> +	ret = cpufreq_frequency_table_cpuinfo(policy, freq_table);
> +	if (ret) {
> +		dev_err(cpu_dev, "invalid frequency table: %d\n", ret);
> +		return ret;
> +	}
> +
> +	policy->cpuinfo.transition_latency = transition_latency;
> +	policy->cur = clk_get_rate(arm_clk) / 1000;
> +	cpumask_setall(policy->cpus);
> +	cpufreq_frequency_table_get_attr(freq_table, policy->cpu);
> +
> +	return 0;
> +}
> +
> +static int imx6q_cpufreq_exit(struct cpufreq_policy *policy)
> +{
> +	cpufreq_frequency_table_put_attr(policy->cpu);
> +	return 0;
> +}
> +
> +static struct freq_attr *imx6q_cpufreq_attr[] = {
> +	&cpufreq_freq_attr_scaling_available_freqs,
> +	NULL,
> +};
> +
> +static struct cpufreq_driver imx6q_cpufreq_driver = {
> +	.verify = imx6q_verify_speed,
> +	.target = imx6q_set_target,
> +	.get = imx6q_get_speed,
> +	.init = imx6q_cpufreq_init,
> +	.exit = imx6q_cpufreq_exit,
> +	.name = "imx6q-cpufreq",
> +	.attr = imx6q_cpufreq_attr,
> +};
> +
> +static int imx6q_cpufreq_probe(struct platform_device *pdev)
> +{
> +	struct device_node *np;
> +	struct opp *opp;
> +	unsigned long min_volt, max_volt;
> +	int num, ret;
> +
> +	cpu_dev = &pdev->dev;
> +
> +	np = of_find_node_by_path("/cpus/cpu at 0");
> +	if (!np) {
> +		dev_err(cpu_dev, "failed to find cpu0 node\n");
> +		return -ENOENT;
> +	}
> +
> +	cpu_dev->of_node = np;
> +
> +	arm_clk = devm_clk_get(cpu_dev, "arm");
> +	pll1_sys_clk = devm_clk_get(cpu_dev, "pll1_sys");
> +	pll1_sw_clk = devm_clk_get(cpu_dev, "pll1_sw");
> +	step_clk = devm_clk_get(cpu_dev, "step");
> +	pll2_pfd2_396m_clk = devm_clk_get(cpu_dev, "pll2_pfd2_396m");
> +	if (IS_ERR(arm_clk) || IS_ERR(pll1_sys_clk) || IS_ERR(pll1_sw_clk) ||
> +	    IS_ERR(step_clk) || IS_ERR(pll2_pfd2_396m_clk)) {
> +		dev_err(cpu_dev, "failed to get clocks\n");
> +		ret = -ENOENT;
> +		goto put_node;
> +	}
> +
> +	arm_reg = devm_regulator_get(cpu_dev, "arm");
> +	pu_reg = devm_regulator_get(cpu_dev, "pu");
> +	soc_reg = devm_regulator_get(cpu_dev, "soc");
> +	if (!arm_reg || !pu_reg || !soc_reg) {
> +		dev_err(cpu_dev, "failed to get regulators\n");
> +		ret = -ENOENT;
> +		goto put_node;
> +	}
> +
> +	/* We expect an OPP table supplied by platform */
> +	num = opp_get_opp_count(cpu_dev);
> +	if (num < 0) {
> +		ret = num;
> +		dev_err(cpu_dev, "no OPP table is found: %d\n", ret);
> +		goto put_node;
> +	}
> +
> +	ret = opp_init_cpufreq_table(cpu_dev, &freq_table);
> +	if (ret) {
> +		dev_err(cpu_dev, "failed to init cpufreq table: %d\n", ret);
> +		goto put_node;
> +	}
> +
> +	if (of_property_read_u32(np, "clock-latency", &transition_latency))
> +		transition_latency = CPUFREQ_ETERNAL;
> +
> +	/*
> +	 * OPP is maintained in order of increasing frequency, and
> +	 * freq_table initialised from OPP is therefore sorted in the
> +	 * same order.
> +	 */
> +	rcu_read_lock();
> +	opp = opp_find_freq_exact(cpu_dev,
> +				  freq_table[0].frequency * 1000, true);
> +	min_volt = opp_get_voltage(opp);
> +	opp = opp_find_freq_exact(cpu_dev,
> +				  freq_table[--num].frequency * 1000, true);
> +	max_volt = opp_get_voltage(opp);
> +	rcu_read_unlock();
> +	ret = regulator_set_voltage_time(arm_reg, min_volt, max_volt);
> +	if (ret > 0)
> +		transition_latency += ret * 1000;
> +
> +	/* Count vddpu and vddsoc latency in for 1.2 GHz support */
> +	if (freq_table[num].frequency == FREQ_1P2_GHZ / 1000) {
> +		ret = regulator_set_voltage_time(pu_reg, PU_SOC_VOLTAGE_NORMAL,
> +						 PU_SOC_VOLTAGE_HIGH);
> +		if (ret > 0)
> +			transition_latency += ret * 1000;
> +		ret = regulator_set_voltage_time(soc_reg, PU_SOC_VOLTAGE_NORMAL,
> +						 PU_SOC_VOLTAGE_HIGH);
> +		if (ret > 0)
> +			transition_latency += ret * 1000;
> +	}
> +
> +	ret = cpufreq_register_driver(&imx6q_cpufreq_driver);
> +	if (ret) {
> +		dev_err(cpu_dev, "failed register driver: %d\n", ret);
> +		goto free_freq_table;
> +	}
> +
> +	of_node_put(np);
> +	return 0;
> +
> +free_freq_table:
> +	opp_free_cpufreq_table(cpu_dev, &freq_table);
> +put_node:
> +	of_node_put(np);
> +	return ret;
> +}
> +
> +static int imx6q_cpufreq_remove(struct platform_device *pdev)
> +{
> +	cpufreq_unregister_driver(&imx6q_cpufreq_driver);
> +	opp_free_cpufreq_table(cpu_dev, &freq_table);
> +
> +	return 0;
> +}
> +
> +static struct platform_driver imx6q_cpufreq_platdrv = {
> +	.driver = {
> +		.name	= "imx6q-cpufreq",
> +		.owner	= THIS_MODULE,
> +	},
> +	.probe		= imx6q_cpufreq_probe,
> +	.remove		= imx6q_cpufreq_remove,
> +};
> +module_platform_driver(imx6q_cpufreq_platdrv);
> +
> +MODULE_AUTHOR("Shawn Guo <shawn.guo at linaro.org>");
> +MODULE_DESCRIPTION("Freescale i.MX6Q cpufreq driver");
> +MODULE_LICENSE("GPL");
> 
-- 
I speak only for myself.
Rafael J. Wysocki, Intel Open Source Technology Center.



More information about the linux-arm-kernel mailing list