[PATCH V1 3/5] mtd: m25p80: add the quad-read support

[Huang Shijie]

On Fri, Aug 23, 2013 at 09:59:09PM +0800, yuhang wang wrote:
> Hi, Shijie
> 
> >>> >  +
> >>
> >> Well, M25p80.c support lots of flash devices, so driver should be as
> >> general as possible. Firstly not all the devices m25p80 supports set
> >> quad mode as your sequence, perhaps write_sr_cr can not match all the
> >
> > It does not matter the NOR flash supports the write_sr_cr() or not,
> > If the NOR flash does not support the write_sr_cr(), it may fails, and you
> > will not set the OPCODE_QIOR for the
> > m25p80_read.
> >
> >
> So your purpose of the patch is to make m25p80 support quad read or
> just support QIOR? if it's the previous one, when set quad support in

The patch makes the m25p80 could supports the Quad read.
it is okay if the quad-read mode set fails.

> DT, but it is possible that quad mode set failed and m25p80 driver
> still read in single mode. In such case, user won't get any error
For the Quadspi driver, if the quad read mode set failed, it will still
run in the Fast Read mode.

> message, so user won't know  what transfer mode the flash works in. Or

do you need a warning when the quad read set fails?

> you just aimed to support QIOR, so the name in DT(quad read) seems not
> appropriate.

sorry, could you explain a little more? how can make the DT seems more
appropriate ?

thanks

> 
> >> m25p80 flash. Secondly, why you only support QIOR(high performance)
> >> not QOR or DOR. Maybe QIOR seems too special, so what if user want to
> >> use QOR if he set quad mode in DTS.
> >>
> > Frankly speaking, i am reluctant to support the QIOR, it is a little slow.
> > :)
> >
> > So the the QIOR is lowest speed for QUADSPI controller, and i do not want to
> > support the DOR.
> >
> > In my new version, i add the support for DDR QIOR read which is the double
> > rate of the QIOR.
> >
> > The user should knows if the NOR flash supports the quad-read or not, and
> > set the proper DT.
> >
> >
> It is slow in your spi system, but to m25p80 it should be general.
> Maybe some others will use that function. So I think it is better to
> supplement the other operations.

it is the other driver's responsibility to add the bits info or the
dummy info to the m25p80 code.


> 
> >> Another point, if command changed to OPCODE_QIOR, there should also
> >> should be some correct in m25p_read. such as the number of dummy data.
> >
> > I only need to change the read opcode.
> >
> >> QIOR can support read without read command if set the certain bit in
> >> transfer, these aspects did not reflect in your patch.
> >>
> > For the Quadspi, it will handle the dummy by the LUT sequence, such as DDR
> > QUAD read, the LUT sequence will
> > set proper dummy (6 cycles for S25FL128S). I do not need the m25p_read to
> > set the dummy.
> >
> >
> Also the same point to above, it is OK to your spi controller, but
> your current m25p80 patch can not content others. If I don't have the
> SPI controller which support LUT sequence, so my spi controller driver
> rely on the info that m25p80 provides, then your patch won't work.

dido.

you can submit a patch to fix this issue if your SPI controller can not
works on this patch.

It is over-design for this patch set to add the bits info/dummy info to
the m25p80 code. 

thanks
Huang Shijie