[RFC v1 3/5] ARM: mvebu: add Armada 150 uart to lowlevel debug

[Jason Cooper]

On Fri, Aug 16, 2013 at 09:41:36PM +0200, Sebastian Hesselbarth wrote:
> This adds UART0 as found on the Armada 1500 to the lowlevel debug of
> mach-mvebu. Unfortunately, default register base addresses for Armada
> 370/XP switched from 0xd000000 to 0xf100000. So, we finally end up
> in three different lowlevel setups:
> 
>  (a) Armada 1500 (possibly also Armada 1000, or MV88DE3xxx in general)
>  (b) Armada 370/XP with new bootloader mapping at 0xf1000000 and
>      the other Orion SoCs (Dove, Kirkwood, Orion5x, MV78xx0)
>  (c) Armada 370/XP with old bootloader mapping at 0xd0000000
> 
> Now, mach-mvebu has been a Armada 370/XP-only playground for a while
> but with great work of Thomas, Gregory, and the others we have moved
> almost all drivers to DT. I suggest to clean-up a little and find
> some meaningful names for the DEBUG_ Kconfigs.
> 
> Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
> ---
> Cc: Russell King <linux at arm.linux.org.uk>
> Cc: Jason Cooper <jason at lakedaemon.net>
> Cc: Andrew Lunn <andrew at lunn.ch>
> Cc: Gregory Clement <gregory.clement at free-electrons.com>
> Cc: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
> Cc: Arnd Bergmann <arnd at arndb.de>
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: linux-kernel at vger.kernel.org
> ---
>  arch/arm/include/debug/mvebu.S |   26 ++++++++++++++++----------
>  1 file changed, 16 insertions(+), 10 deletions(-)
> 
> diff --git a/arch/arm/include/debug/mvebu.S b/arch/arm/include/debug/mvebu.S
> index 6517311..ca41c02 100644
> --- a/arch/arm/include/debug/mvebu.S
> +++ b/arch/arm/include/debug/mvebu.S
> @@ -11,19 +11,25 @@
>   * published by the Free Software Foundation.
>  */
>  
> -#ifdef CONFIG_DEBUG_MVEBU_UART_ALTERNATE
> -#define ARMADA_370_XP_REGS_PHYS_BASE	0xf1000000
> -#else
> -#define ARMADA_370_XP_REGS_PHYS_BASE	0xd0000000
> +#if defined(CONFIG_MACH_ARMADA_1500)
> +#define MVEBU_REGS_PHYS_BASE	0xf7f80000
> +#define MVEBU_REGS_VIRT_BASE	0xf7f80000
> +#define MVEBU_UART0_OFFSET	0x00049000


> +#elif defined(CONFIG_DEBUG_MVEBU_UART)
> +#define MVEBU_REGS_PHYS_BASE	0xd0000000
> +#define MVEBU_REGS_VIRT_BASE	0xfec00000
> +#define MVEBU_UART0_OFFSET	0x00012000
> +#else /* CONFIG_DEBUG_MVEBU_UART_ALTERNATE */
> +#define MVEBU_REGS_PHYS_BASE	0xf1000000
> +#define MVEBU_REGS_VIRT_BASE	0xfec00000
> +#define MVEBU_UART0_OFFSET	0x00012000
>  #endif

We should preserve the default like so:

+#elif defined(CONFIG_DEBUG_MVEBU_UART_ALTERNATE)
+#define MVEBU_REGS_PHYS_BASE	0xf1000000
+#define MVEBU_REGS_VIRT_BASE	0xfec00000
+#define MVEBU_UART0_OFFSET	0x00012000
+#else /* CONFIG_DEBUG_MVEBU_UART */
+#define MVEBU_REGS_PHYS_BASE	0xd0000000
+#define MVEBU_REGS_VIRT_BASE	0xfec00000
+#define MVEBU_UART0_OFFSET	0x00012000
 #endif

thx,

Jason.