[PATCH v3] arm: dts: AM43x: Add usb DT nodes for AM4372

[Benoit Cousson]

+ Roger

Hi George,

Yes, I had some comment about the "ti'type" in Roger's series that will 
be applicable here as well.


On 14/08/2013 16:16, George Cherian wrote:
> +Benoit
>   If you dont have any comments, can you take this for 3.12?
>
> Regards
> -George
>
> On 7/10/2013 1:44 PM, George Cherian wrote:
>
>> This patch adds
>>     - HS USB nodes
>>     - phy nodes
>>     - usb control module nodes.
>>
>> Signed-off-by: George Cherian <george.cherian at ti.com>
>> ---
>>
>> changes from v2
>> change synopsis to snps
>> use simple node names
>> add both USB and PHY instances
>> add usbctrl node
>>
>> changes from v1
>> renamed synopsis to snps
>> removed flag tx-fifo-resize
>>
>>   arch/arm/boot/dts/am4372.dtsi | 58
>> +++++++++++++++++++++++++++++++++++++++++++
>>   1 file changed, 58 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/am4372.dtsi
>> b/arch/arm/boot/dts/am4372.dtsi
>> index ddc1df7..37f196f 100644
>> --- a/arch/arm/boot/dts/am4372.dtsi
>> +++ b/arch/arm/boot/dts/am4372.dtsi
>> @@ -64,5 +64,63 @@
>>               compatible = "ti,am4372-counter32k","ti,omap-counter32k";
>>               reg = <0x44e86000 0x40>;
>>           };
>> +
>> +        phy1: usbphy1 {
>> +            compatible = "ti,am4372-usb2";

That's not a very good name for a phy? It looks like a usb module.

The bindings specify only ti,omap-usb2 or ti,omap-usb3 for USB2 or USB3.
I guess it should be one of them and potentially the binding should be 
updated with ti,omap-usb2-phy and ti,omap-usb3-phy names while we can 
still do it.

>> +            #phy-cells = <0>;
>> +            id = <0>;
>> +            status = "disabled";
>> +        };
>> +
>> +        phy2: usbphy2 {

Why do you need a different node name here? It should be a generic name 
to identify the function, so usbphy or usb-phy seems good enough.

>> +            compatible = "ti,am4372-usb2";
>> +            #phy-cells = <0>;
>> +            id = <1>;
>> +            status = "disabled";
>> +        };
>> +
>> +        usbctrl: omap-control-usb at 44e10620 {
>> +            compatible = "ti,omap-control-usb";
>> +            reg = <0x44e10620 0x10>;
>> +            reg-names = "control_dev_conf";
>> +            ti,type = <3>;
>> +            status = "disabled";
>> +        };
>> +
>> +        usb1: am4372_dwc3 at 48380000 {
>> +            status = "disabled";
>> +            compatible = "ti,am4372-dwc3";
>> +            reg = <0x48380000 0x200>;
>> +            interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
>> +            #address-cells = <1>;
>> +            #size-cells = <1>;
>> +            utmi-mode = <1>;
>> +            ranges;

A blank line here will be nice.

>> +            dwc3 at 48390000 {
>> +                compatible = "snps,dwc3";
>> +                reg = <0x48390000 0xd000>;
>> +                interrupts = <GIC_SPI  168 IRQ_TYPE_LEVEL_HIGH>;
>> +                phys = <&phy1>;
>> +                phy-names = "am4372-usb1";

What is the purpose of the phy-names? Is it relevant to add the SoC name 
in something that usually, at least for the clocks and IRQs, is IP specific?

The current documentation does not explain it and does not support phys 
property either.

   synopsys DWC3 CORE

   DWC3- USB3 CONTROLLER

   Required properties:
    - compatible: must be "synopsys,dwc3"
    - reg : Address and length of the register set for the device
    - interrupts: Interrupts used by the dwc3 controller.
    - usb-phy : array of phandle for the PHY device

Is there some binding update ongoing for 3.12?

>> +            };
>> +        };
>> +
>> +        usb2: am4372_dwc3 at 483c0000 {
>> +            status = "disabled";
>> +            compatible = "ti,am4372-dwc3";
>> +            reg = <0x483c0000 0x200>;
>> +            interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
>> +            #address-cells = <1>;
>> +            #size-cells = <1>;
>> +            utmi-mode = <1>;
>> +            ranges;

A blank line here will be nice.

>> +            dwc3 at 483d0000 {
>> +                compatible = "snps,dwc3";
>> +                reg = <0x483d0000 0xd000>;
>> +                interrupts = <GIC_SPI  174 IRQ_TYPE_LEVEL_HIGH>;
>> +                phys = <&phy2>;
>> +                phy-names = "am4372-usb2";
>> +            };
>> +        };
>>       };
>>   };
>
>

Regards,
Benoit