[PATCH v14 00/12] Add tested id switch and vbus connect detect support for Chipidea

[Peter Chen]

On Fri, Aug 02, 2013 at 04:33:53PM +0800, Peter Chen wrote:
> This patchset adds tested otg id switch function and vbus connect
> and disconnect detection for chipidea driver. And fix kinds of 
> bugs found at chipidea drivers after enabling id and vbus detection.
> 
> This patch are fully tested at imx6 sabresd and imx28evk platform by me.
> Besides, marek tested it on two STMP3780-based boards (not yet mainline)
> and two MX28-based boards.
> 
> My chipidea repo: https://github.com/hzpeterchen/linux-usb.git
> 
> Changes for v14:
> - This patchset is based on below recent chipidea patches and newest
> usb-next, it can decrease rebase effort.
> 
> Fabio Estevam (3):
>   chipidea: ci_hdrc_imx: Remove unused variable 'res'
>   chipidea: core: Move hw_phymode_configure() into probe
>   chipidea: Remove previous MODULE_ALIAS
> 
> Lothar Wabmann (3):
>   usb: chipidea: improve kconfig 2.0
>   usb: chipidea: don't clobber return value of ci_role_start()
>   usb: chipidea: ci_hdrc_imx: remove an unsolicited module_put() call
>     from ci_hdrc_imx_remove()
> 
> Peter Chen (1):
>   usb: chipidea: fix the build error with randconfig
> 
> - [Michael comments]: move vbus operation to core, and squash two vbus
> patches. [1/12], [2/12]
> - [Michael comments]: move out non vbus and non id related patches. [14/14 at v13]

Hi Alex, any comments?

> 
> Chagnes for v13:
> - Add Tested-by: Marek Vasut <marex at denx.de>
> - [Sascha's comments]: Add return value check for devm_regulator_get. [3/14]
> - [Marc's comments]: Change timeout usage at hw_wait_reg. [11/14]
> - [Alex's comments]: Using platdata flag to indicate dual role but not 
> OTG controller. [7/14]
> 
> Changes for v12:
> - Rebased greg's usb-next tree (3.10.0-rc7+)
> - Split more small patches for single function and fix.
> 
> Peter Chen (12):
>   usb: chipidea: move vbus regulator operation to core
>   usb: chipidea: host: add vbus regulator control
>   usb: chipidea: udc: otg_set_peripheral is useless for some chipidea
>     users
>   usb: chipidea: otg: Add otg file used to access otgsc
>   usb: chipidea: Add role init and destory APIs
>   usb: chipidea: add flag CI_HDRC_DUAL_ROLE_NOT_OTG
>   usb: chipidea: disable all interrupts and clear all interrupts status
>   usb: chipidea: move otg relate things to otg file
>   usb: chipidea: add vbus interrupt handler
>   usb: chipidea: add wait vbus lower than OTGSC_BSV before role starts
>   usb: chipidea: udc: misuse flag CI_HDRC_REGS_SHARED and
>     CI_HDRC_PULLUP_ON_VBUS
>   usb: chipidea: udc: .pullup is valid when vbus is on at
>     CI_HDRC_PULLUP_ON_VBUS
> 
>  drivers/usb/chipidea/Makefile      |    2 +-
>  drivers/usb/chipidea/bits.h        |   10 ++
>  drivers/usb/chipidea/ci.h          |    8 ++
>  drivers/usb/chipidea/ci_hdrc_imx.c |   26 +-----
>  drivers/usb/chipidea/core.c        |  184 +++++++++++++++++++++++++-----------
>  drivers/usb/chipidea/host.c        |   30 ++++++-
>  drivers/usb/chipidea/host.h        |    6 +
>  drivers/usb/chipidea/otg.c         |  135 ++++++++++++++++++++++++++
>  drivers/usb/chipidea/otg.h         |   22 +++++
>  drivers/usb/chipidea/udc.c         |   59 +++++++++---
>  drivers/usb/chipidea/udc.h         |    6 +
>  include/linux/usb/chipidea.h       |    6 +
>  12 files changed, 401 insertions(+), 93 deletions(-)
>  create mode 100644 drivers/usb/chipidea/otg.c
>  create mode 100644 drivers/usb/chipidea/otg.h
> 

-- 

Best Regards,
Peter Chen