[PATCH V2 7/8] ARM: tegra: add LP1 suspend support for Tegra114
Joseph Lo
josephl at nvidia.com
Mon Aug 5 07:21:03 EDT 2013
The LP1 suspend mode will power off the CPU, clock gated the PLLs and put
SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The
sequence when LP1 suspending:
* tunning off L1 data cache and the MMU
* storing some EMC registers, DPD (deep power down) status, clk source of
mselect and SCLK burst policy
* putting SDRAM into self-refresh
* switching CPU to CLK_M (12MHz OSC)
* tunning off PLLM, PLLP, PLLA, PLLC and PLLX
* switching SCLK to CLK_S (32KHz OSC)
* shutting off the CPU rail
The sequence of LP1 resuming:
* re-enabling PLLM, PLLP, PLLA, PLLC and PLLX
* restoring the clk source of mselect and SCLK burst policy
* restoring DPD status and some EMC registers
* resuming SDRAM to normal mode
* jumping to the "tegra_resume" from PMC_SCRATCH41
Due to the SDRAM will be put into self-refresh mode, the low level
procedures of LP1 suspending and resuming should be copied to
TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before
restoring the CPU context when resuming, the SDRAM needs to be switched
back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy
be restored. Then jumping to "tegra_resume" that was expected to be stored
in PMC_SCRATCH41 to restore CPU context and back to kernel.
Based on the work by: Bo Yan <byan at nvidia.com>
Signed-off-by: Joseph Lo <josephl at nvidia.com>
---
V2:
* using IS_ENABLE for SoC specific code
* moving the fix of PLL lock func to previous patch
---
arch/arm/mach-tegra/Makefile | 1 +
arch/arm/mach-tegra/iomap.h | 6 ++
arch/arm/mach-tegra/pm.c | 8 +-
arch/arm/mach-tegra/sleep-tegra30.S | 141 ++++++++++++++++++++++++++++++++----
4 files changed, 140 insertions(+), 16 deletions(-)
diff --git a/arch/arm/mach-tegra/Makefile b/arch/arm/mach-tegra/Makefile
index a3fe22d..f4e7063 100644
--- a/arch/arm/mach-tegra/Makefile
+++ b/arch/arm/mach-tegra/Makefile
@@ -33,6 +33,7 @@ obj-$(CONFIG_TEGRA_PCI) += pcie.o
obj-$(CONFIG_ARCH_TEGRA_114_SOC) += tegra114_speedo.o
obj-$(CONFIG_ARCH_TEGRA_114_SOC) += sleep-tegra30.o
+obj-$(CONFIG_ARCH_TEGRA_114_SOC) += pm-tegra30.o
ifeq ($(CONFIG_CPU_IDLE),y)
obj-$(CONFIG_ARCH_TEGRA_114_SOC) += cpuidle-tegra114.o
endif
diff --git a/arch/arm/mach-tegra/iomap.h b/arch/arm/mach-tegra/iomap.h
index f2bdcb4..aba3629 100644
--- a/arch/arm/mach-tegra/iomap.h
+++ b/arch/arm/mach-tegra/iomap.h
@@ -239,6 +239,12 @@
#define TEGRA_KFUSE_BASE 0x7000FC00
#define TEGRA_KFUSE_SIZE SZ_1K
+#define TEGRA_EMC0_BASE 0x7001A000
+#define TEGRA_EMC0_SIZE SZ_2K
+
+#define TEGRA_EMC1_BASE 0x7001A800
+#define TEGRA_EMC1_SIZE SZ_2K
+
#define TEGRA_CSITE_BASE 0x70040000
#define TEGRA_CSITE_SIZE SZ_256K
diff --git a/arch/arm/mach-tegra/pm.c b/arch/arm/mach-tegra/pm.c
index 25f3df0..98e1a79 100644
--- a/arch/arm/mach-tegra/pm.c
+++ b/arch/arm/mach-tegra/pm.c
@@ -216,7 +216,9 @@ static bool tegra_lp1_iram_hook(void)
tegra20_lp1_iram_hook();
break;
case TEGRA30:
- if (IS_ENABLED(CONFIG_ARCH_TEGRA_3x_SOC))
+ case TEGRA114:
+ if (IS_ENABLED(CONFIG_ARCH_TEGRA_3x_SOC) ||
+ IS_ENABLED(CONFIG_ARCH_TEGRA_114_SOC))
tegra30_lp1_iram_hook();
break;
default:
@@ -242,7 +244,9 @@ static bool tegra_sleep_core_init(void)
tegra20_sleep_core_init();
break;
case TEGRA30:
- if (IS_ENABLED(CONFIG_ARCH_TEGRA_3x_SOC))
+ case TEGRA114:
+ if (IS_ENABLED(CONFIG_ARCH_TEGRA_3x_SOC) ||
+ IS_ENABLED(CONFIG_ARCH_TEGRA_114_SOC))
tegra30_sleep_core_init();
break;
default:
diff --git a/arch/arm/mach-tegra/sleep-tegra30.S b/arch/arm/mach-tegra/sleep-tegra30.S
index f29866f..6c9ca86 100644
--- a/arch/arm/mach-tegra/sleep-tegra30.S
+++ b/arch/arm/mach-tegra/sleep-tegra30.S
@@ -65,6 +65,10 @@
#define CLK_RESET_PLLA_MISC 0xbc
#define CLK_RESET_PLLX_BASE 0xe0
#define CLK_RESET_PLLX_MISC 0xe4
+#define CLK_RESET_PLLX_MISC3 0x518
+#define CLK_RESET_PLLX_MISC3_IDDQ 3
+#define CLK_RESET_PLLM_MISC_IDDQ 5
+#define CLK_RESET_PLLC_MISC_IDDQ 26
#define CLK_RESET_CLK_SOURCE_MSELECT 0x3b4
@@ -114,6 +118,18 @@
beq 1b
.endm
+.macro pll_iddq_exit, rd, car, iddq, iddq_bit
+ ldr \rd, [\car, #\iddq]
+ bic \rd, \rd, #(1<<\iddq_bit)
+ str \rd, [\car, #\iddq]
+.endm
+
+.macro pll_iddq_entry, rd, car, iddq, iddq_bit
+ ldr \rd, [\car, #\iddq]
+ orr \rd, \rd, #(1<<\iddq_bit)
+ str \rd, [\car, #\iddq]
+.endm
+
#if defined(CONFIG_HOTPLUG_CPU) || defined(CONFIG_PM_SLEEP)
/*
* tegra30_hotplug_shutdown(void)
@@ -315,6 +331,32 @@ ENTRY(tegra30_lp1_reset)
str r1, [r0, #CLK_RESET_CCLK_DIVIDER]
str r1, [r0, #CLK_RESET_SCLK_DIVIDER]
+ tegra_get_soc_id TEGRA_APB_MISC_BASE, r10
+ cmp r10, #TEGRA30
+ beq _no_pll_iddq_exit
+
+ pll_iddq_exit r1, r0, CLK_RESET_PLLM_MISC, CLK_RESET_PLLM_MISC_IDDQ
+ pll_iddq_exit r1, r0, CLK_RESET_PLLC_MISC, CLK_RESET_PLLC_MISC_IDDQ
+ pll_iddq_exit r1, r0, CLK_RESET_PLLX_MISC3, CLK_RESET_PLLX_MISC3_IDDQ
+
+ mov32 r7, TEGRA_TMRUS_BASE
+ ldr r1, [r7]
+ add r1, r1, #2
+ wait_until r1, r7, r3
+
+ /* enable PLLM via PMC */
+ mov32 r2, TEGRA_PMC_BASE
+ ldr r1, [r2, #PMC_PLLP_WB0_OVERRIDE]
+ orr r1, r1, #(1 << 12)
+ str r1, [r2, #PMC_PLLP_WB0_OVERRIDE]
+
+ pll_enable r1, r0, CLK_RESET_PLLM_BASE, 0
+ pll_enable r1, r0, CLK_RESET_PLLC_BASE, 0
+ pll_enable r1, r0, CLK_RESET_PLLX_BASE, 0
+
+ b _pll_m_c_x_done
+
+_no_pll_iddq_exit:
/* enable PLLM via PMC */
mov32 r2, TEGRA_PMC_BASE
ldr r1, [r2, #PMC_PLLP_WB0_OVERRIDE]
@@ -322,11 +364,13 @@ ENTRY(tegra30_lp1_reset)
str r1, [r2, #PMC_PLLP_WB0_OVERRIDE]
pll_enable r1, r0, CLK_RESET_PLLM_BASE, CLK_RESET_PLLM_MISC
- pll_enable r1, r0, CLK_RESET_PLLP_BASE, CLK_RESET_PLLP_MISC
- pll_enable r1, r0, CLK_RESET_PLLA_BASE, CLK_RESET_PLLA_MISC
pll_enable r1, r0, CLK_RESET_PLLC_BASE, CLK_RESET_PLLC_MISC
pll_enable r1, r0, CLK_RESET_PLLX_BASE, CLK_RESET_PLLX_MISC
+_pll_m_c_x_done:
+ pll_enable r1, r0, CLK_RESET_PLLP_BASE, CLK_RESET_PLLP_MISC
+ pll_enable r1, r0, CLK_RESET_PLLA_BASE, CLK_RESET_PLLA_MISC
+
pll_locked r1, r0, CLK_RESET_PLLM_BASE
pll_locked r1, r0, CLK_RESET_PLLP_BASE
pll_locked r1, r0, CLK_RESET_PLLA_BASE
@@ -346,8 +390,10 @@ ENTRY(tegra30_lp1_reset)
ldr r4, [r5, #0x1C] @ restore SCLK_BURST
str r4, [r0, #CLK_RESET_SCLK_BURST]
- mov32 r4, ((1 << 28) | (0x8)) @ burst policy is PLLX
- str r4, [r0, #CLK_RESET_CCLK_BURST]
+ cmp r10, #TEGRA30
+ movweq r4, #:lower16:((1 << 28) | (0x8)) @ burst policy is PLLX
+ movteq r4, #:upper16:((1 << 28) | (0x8))
+ streq r4, [r0, #CLK_RESET_CCLK_BURST]
/* Restore pad power state to normal */
ldr r1, [r5, #0x14] @ PMC_IO_DPD_STATUS
@@ -356,8 +402,13 @@ ENTRY(tegra30_lp1_reset)
orr r1, r1, #(1 << 30)
str r1, [r2, #PMC_IO_DPD_REQ] @ DPD_OFF
- mov32 r0, TEGRA_EMC_BASE @ r0 reserved for emc base
+ cmp r10, #TEGRA30
+ movweq r0, #:lower16:TEGRA_EMC_BASE @ r0 reserved for emc base
+ movteq r0, #:upper16:TEGRA_EMC_BASE
+ movwne r0, #:lower16:TEGRA_EMC0_BASE
+ movtne r0, #:upper16:TEGRA_EMC0_BASE
+exit_self_refresh:
ldr r1, [r5, #0xC] @ restore EMC_XM2VTTGENPADCTRL
str r1, [r0, #EMC_XM2VTTGENPADCTRL]
ldr r1, [r5, #0x10] @ restore EMC_XM2VTTGENPADCTRL2
@@ -372,8 +423,14 @@ ENTRY(tegra30_lp1_reset)
emc_timing_update r1, r0
+ cmp r10, #TEGRA114
+ movweq r1, #:lower16:TEGRA_EMC1_BASE
+ movteq r1, #:upper16:TEGRA_EMC1_BASE
+ cmpeq r0, r1
+
ldr r1, [r0, #EMC_AUTO_CAL_CONFIG]
orr r1, r1, #(1 << 31) @ set AUTO_CAL_ACTIVE
+ orreq r1, r1, #(1 << 27) @ set slave mode for channel 1
str r1, [r0, #EMC_AUTO_CAL_CONFIG]
emc_wait_auto_cal_onetime:
@@ -388,9 +445,10 @@ emc_wait_auto_cal_onetime:
mov r1, #0
str r1, [r0, #EMC_SELF_REF] @ take DRAM out of self refresh
mov r1, #1
- str r1, [r0, #EMC_NOP]
- str r1, [r0, #EMC_NOP]
- str r1, [r0, #EMC_REFRESH]
+ cmp r10, #TEGRA30
+ streq r1, [r0, #EMC_NOP]
+ streq r1, [r0, #EMC_NOP]
+ streq r1, [r0, #EMC_REFRESH]
emc_device_mask r1, r0
@@ -452,6 +510,16 @@ zcal_done:
ldr r1, [r5, #0x0] @ restore EMC_CFG
str r1, [r0, #EMC_CFG]
+ /* Tegra114 had dual EMC channel, now config the other one */
+ cmp r10, #TEGRA114
+ bne __no_dual_emc_chanl
+ mov32 r1, TEGRA_EMC1_BASE
+ cmp r0, r1
+ movne r0, r1
+ addne r5, r5, #0x20
+ bne exit_self_refresh
+__no_dual_emc_chanl:
+
mov32 r0, TEGRA_PMC_BASE
ldr r0, [r0, #PMC_SCRATCH41]
mov pc, r0 @ jump to tegra_resume
@@ -468,12 +536,30 @@ tegra30_sdram_pad_address:
.word TEGRA_CLK_RESET_BASE + CLK_RESET_CLK_SOURCE_MSELECT @0x18
.word TEGRA_CLK_RESET_BASE + CLK_RESET_SCLK_BURST @0x1c
+tegra114_sdram_pad_address:
+ .word TEGRA_EMC0_BASE + EMC_CFG @0x0
+ .word TEGRA_EMC0_BASE + EMC_ZCAL_INTERVAL @0x4
+ .word TEGRA_EMC0_BASE + EMC_AUTO_CAL_INTERVAL @0x8
+ .word TEGRA_EMC0_BASE + EMC_XM2VTTGENPADCTRL @0xc
+ .word TEGRA_EMC0_BASE + EMC_XM2VTTGENPADCTRL2 @0x10
+ .word TEGRA_PMC_BASE + PMC_IO_DPD_STATUS @0x14
+ .word TEGRA_CLK_RESET_BASE + CLK_RESET_CLK_SOURCE_MSELECT @0x18
+ .word TEGRA_CLK_RESET_BASE + CLK_RESET_SCLK_BURST @0x1c
+ .word TEGRA_EMC1_BASE + EMC_CFG @0x20
+ .word TEGRA_EMC1_BASE + EMC_ZCAL_INTERVAL @0x24
+ .word TEGRA_EMC1_BASE + EMC_AUTO_CAL_INTERVAL @0x28
+ .word TEGRA_EMC1_BASE + EMC_XM2VTTGENPADCTRL @0x2c
+ .word TEGRA_EMC1_BASE + EMC_XM2VTTGENPADCTRL2 @0x30
+
tegra30_sdram_pad_size:
- .word tegra30_sdram_pad_size - tegra30_sdram_pad_address
+ .word tegra114_sdram_pad_address - tegra30_sdram_pad_address
+
+tegra114_sdram_pad_size:
+ .word tegra30_sdram_pad_size - tegra114_sdram_pad_address
.type tegra30_sdram_pad_save, %object
tegra30_sdram_pad_save:
- .rept (tegra30_sdram_pad_size - tegra30_sdram_pad_address) / 4
+ .rept (tegra30_sdram_pad_size - tegra114_sdram_pad_address) / 4
.long 0
.endr
@@ -497,6 +583,7 @@ tegra30_tear_down_core:
* r5 = TEGRA_CLK_RESET_BASE
* r6 = TEGRA_FLOW_CTRL_BASE
* r7 = TEGRA_TMRUS_BASE
+ * r10= SoC ID
*/
tegra30_switch_cpu_to_clk32k:
/*
@@ -543,6 +630,11 @@ tegra30_switch_cpu_to_clk32k:
bic r0, r0, #(1 << 30)
str r0, [r5, #CLK_RESET_PLLX_BASE]
+ cmp r10, #TEGRA30
+ beq _no_pll_in_iddq
+ pll_iddq_entry r1, r5, CLK_RESET_PLLX_MISC3, CLK_RESET_PLLX_MISC3_IDDQ
+_no_pll_in_iddq:
+
/* switch to CLKS */
mov r0, #0 /* brust policy = 32KHz */
str r0, [r5, #CLK_RESET_SCLK_BURST]
@@ -594,14 +686,19 @@ halted:
* r5 = TEGRA_CLK_RESET_BASE
* r6 = TEGRA_FLOW_CTRL_BASE
* r7 = TEGRA_TMRUS_BASE
+ * r10= SoC ID
*/
tegra30_sdram_self_refresh:
- adr r2, tegra30_sdram_pad_address
adr r8, tegra30_sdram_pad_save
+ tegra_get_soc_id TEGRA_APB_MISC_BASE, r10
+ cmp r10, #TEGRA30
+ adreq r2, tegra30_sdram_pad_address
+ ldreq r3, tegra30_sdram_pad_size
+ adrne r2, tegra114_sdram_pad_address
+ ldrne r3, tegra114_sdram_pad_size
mov r9, #0
- ldr r3, tegra30_sdram_pad_size
padsave:
ldr r0, [r2, r9] @ r0 is the addr in the pad_address
@@ -615,13 +712,18 @@ padsave_done:
dsb
- mov32 r0, TEGRA_EMC_BASE @ r0 reserved for emc base addr
+ cmp r10, #TEGRA30
+ ldreq r0, =TEGRA_EMC_BASE @ r0 reserved for emc base addr
+ ldrne r0, =TEGRA_EMC0_BASE
+enter_self_refresh:
+ cmp r10, #TEGRA30
mov r1, #0
str r1, [r0, #EMC_ZCAL_INTERVAL]
str r1, [r0, #EMC_AUTO_CAL_INTERVAL]
ldr r1, [r0, #EMC_CFG]
bic r1, r1, #(1 << 28)
+ bicne r1, r1, #(1 << 29)
str r1, [r0, #EMC_CFG] @ disable DYN_SELF_REF
emc_timing_update r1, r0
@@ -660,11 +762,22 @@ emcself:
and r1, r1, r2
str r1, [r0, #EMC_XM2VTTGENPADCTRL]
ldr r1, [r0, #EMC_XM2VTTGENPADCTRL2]
- orr r1, r1, #7 @ set E_NO_VTTGEN
+ cmp r10, #TEGRA30
+ orreq r1, r1, #7 @ set E_NO_VTTGEN
+ orrne r1, r1, #0x3f
str r1, [r0, #EMC_XM2VTTGENPADCTRL2]
emc_timing_update r1, r0
+ /* Tegra114 had dual EMC channel, now config the other one */
+ cmp r10, #TEGRA114
+ bne no_dual_emc_chanl
+ mov32 r1, TEGRA_EMC1_BASE
+ cmp r0, r1
+ movne r0, r1
+ bne enter_self_refresh
+no_dual_emc_chanl:
+
ldr r1, [r4, #PMC_CTRL]
tst r1, #PMC_CTRL_SIDE_EFFECT_LP0
bne pmc_io_dpd_skip
--
1.8.3.4
More information about the linux-arm-kernel
mailing list