[PATCH 1/3] Add support for GMT G72/G763 PWM fan controller

[Arnaud Ebalard]

Hi,

Andrew Lunn <andrew at lunn.ch> writes:

> Hi Arnaud
>
>> +static DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, get_pwm, set_pwm);
>> +static DEVICE_ATTR(pwm1_polarity, S_IWUSR | S_IRUGO,
>> +		   get_pwm_polarity, set_pwm_polarity);
>> +static DEVICE_ATTR(pwm1_mode, S_IWUSR | S_IRUGO,
>> +		   get_pwm_mode, set_pwm_mode);
>> +static DEVICE_ATTR(pwm1_enable, S_IWUSR | S_IRUGO,
>> +		   get_speed_control_mode, set_speed_control_mode);
>> +static DEVICE_ATTR(pwm1_freq, S_IWUSR | S_IRUGO,
>> +		   get_pwm_freq, set_pwm_freq);
>> +
>> +static DEVICE_ATTR(fan1_input, S_IRUGO, get_fan_rpm, NULL);
>> +static DEVICE_ATTR(fan1_alarm, S_IRUGO, get_fan_ooc, NULL);
>> +static DEVICE_ATTR(fan1_alarm_detection, S_IWUSR | S_IRUGO,
>> +		   get_fan_ooc_detection, set_fan_ooc_detection);
>> +static DEVICE_ATTR(fan1_fault, S_IRUGO, get_fan_failure, NULL);
>> +static DEVICE_ATTR(fan1_fault_detection, S_IWUSR | S_IRUGO,
>> +		   get_fan_failure_detection, set_fan_failure_detection);
>> +static DEVICE_ATTR(fan1_target, S_IWUSR | S_IRUGO,
>> +		   get_fan_target, set_fan_target);
>> +static DEVICE_ATTR(fan1_pulses, S_IWUSR | S_IRUGO,
>> +		   get_fan_pulses, set_fan_pulses);
>> +static DEVICE_ATTR(fan1_div, S_IWUSR | S_IRUGO,
>> +		   get_fan_clk_div, set_fan_clk_div);
>> +static DEVICE_ATTR(fan1_gear_mode, S_IWUSR | S_IRUGO,
>> +		   get_fan_gear_mode, set_fan_gear_mode);
>> +static DEVICE_ATTR(fan1_startup_voltage, S_IWUSR | S_IRUGO,
>> +		   get_fan_startup_voltage, set_fan_startup_voltage);
>
> It is normal to use SENSOR_ATTR, not DEVICE_ATTR. Take a look at the
> existing fan drivers.

I will take a look and use SENSOR_ATTR if it is the expected way. For
the records, the g760a.c which I used as basis uses DEVICE_ATTR ;-)

> I also think a lot of these are not needed. They are fixed properties
> of the board and cannot change dynamically. They are set once using DT
> and user space does not need to care.

I added those knobs for a simple reason: I don't have all the various
characteristics of the target platform I am working on (Netgear
ReadyNAS Duo v2) and needed to be able to test various values w/o
rebooting to get those rights. I thought this knobs would be useful for
people with the same issue (for instance, the new ReadyNAS 102 also has
a G762) and would not hurt.

Anyway, I will split the patch in two parts and keep the useless knobs
on my side.

Thanks for your feedback,

Cheers,

a+