[PATCH 1/3] Add support for GMT G72/G763 PWM fan controller
Guenter Roeck
linux at roeck-us.net
Fri Apr 19 00:35:55 EDT 2013
On Fri, Apr 19, 2013 at 12:28:21AM +0200, Arnaud Ebalard wrote:
>
> Signed-off-by: Arnaud Ebalard <arno at natisbad.org>
> Tested-by: Arnaud Ebalard <arno at natisbad.org>
> ---
> drivers/hwmon/Kconfig | 10 +
> drivers/hwmon/Makefile | 1 +
> drivers/hwmon/g762.c | 1159 ++++++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 1170 insertions(+)
> create mode 100644 drivers/hwmon/g762.c
>
checkpatch says:
total: 1 errors, 15 warnings, 0 checks, 1182 lines checked
Please fix those. Also, please make sure there are spaces around operators.
Additional comments inline. This is not a complete review; I gave up after
a while. Please fix the problems and resubmit.
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index 89ac1cb..0c6ddee 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -423,6 +423,16 @@ config SENSORS_G760A
> This driver can also be built as a module. If so, the module
> will be called g760a.
>
> +config SENSORS_G762
> + tristate "GMT G762"
> + depends on I2C
> + help
> + If you say yes here you get support for Global Mixed-mode
> + Technology Inc G762 fan speed PWM controller chips.
> +
> + This driver can also be built as a module. If so, the module
> + will be called g762a.
> +
> config SENSORS_GL518SM
> tristate "Genesys Logic GL518SM"
> depends on I2C
> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> index 8d6d97e..4b49504 100644
> --- a/drivers/hwmon/Makefile
> +++ b/drivers/hwmon/Makefile
> @@ -57,6 +57,7 @@ obj-$(CONFIG_SENSORS_F75375S) += f75375s.o
> obj-$(CONFIG_SENSORS_FAM15H_POWER) += fam15h_power.o
> obj-$(CONFIG_SENSORS_FSCHMD) += fschmd.o
> obj-$(CONFIG_SENSORS_G760A) += g760a.o
> +obj-$(CONFIG_SENSORS_G762) += g762.o
> obj-$(CONFIG_SENSORS_GL518SM) += gl518sm.o
> obj-$(CONFIG_SENSORS_GL520SM) += gl520sm.o
> obj-$(CONFIG_SENSORS_GPIO_FAN) += gpio-fan.o
> diff --git a/drivers/hwmon/g762.c b/drivers/hwmon/g762.c
> new file mode 100644
> index 0000000..8c4cb39
> --- /dev/null
> +++ b/drivers/hwmon/g762.c
> @@ -0,0 +1,1159 @@
> +/*
> + * g762 - Driver for the Global Mixed-mode Technology Inc. fan speed PWM
> + * controller chips from G762 family, i.e. G762 and G763
> + *
> + * Copyright (C) 2013, Arnaud EBALARD <arno at natisbad.org>
> + *
> + * This work is based on a basic version for 2.6.31 kernel developed
> + * by Olivier Mouchet for LaCie NAS. Updates have been performed to run
> + * on recent kernels. Supported has been completed and additional
> + * features added: ability to configure various characteristics from
> + * .dts file, better initialization, alarms and error reporting support,
> + * gear mode, polarity, fan pulse per revolution, fan startup voltage
> + * control. The following detailed datasheet has been used as a basis
> + * for this work:
> + *
> + * http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf
> + *
> + * Headers from previous developments have been kept below:
> + *
> + * Copyright (c) 2009 LaCie
> + *
> + * Author: Olivier Mouchet <olivier.mouchet at gmail.com>
> + *
> + * based on g760a code written by Herbert Valerio Riedel <hvr at gnu.org>
> + * Copyright (C) 2007 Herbert Valerio Riedel <hvr at gnu.org>
> + *
> + * g762: minimal datasheet available at:
> + * http://www.gmt.com.tw/product/datasheet/EDS-762_3.pdf
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
> + */
> +
> +#include <linux/device.h>
> +#include <linux/module.h>
> +#include <linux/init.h>
> +#include <linux/slab.h>
> +#include <linux/jiffies.h>
> +#include <linux/i2c.h>
> +#include <linux/hwmon.h>
> +#include <linux/hwmon-sysfs.h>
> +#include <linux/err.h>
> +#include <linux/mutex.h>
> +#include <linux/kernel.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +
> +#define DRVNAME "g762"
> +
> +static const struct i2c_device_id g762_id[] = {
> + { DRVNAME, 0 },
> + { }
> +};
> +MODULE_DEVICE_TABLE(i2c, g762_id);
> +
> +enum g762_regs {
> + G762_REG_SET_CNT = 0x00,
> + G762_REG_ACT_CNT = 0x01,
> + G762_REG_FAN_STA = 0x02,
> + G762_REG_SET_OUT = 0x03,
> + G762_REG_FAN_CMD1 = 0x04,
> + G762_REG_FAN_CMD2 = 0x05,
> +};
> +
> +/* Config register bits */
> +#define G762_REG_FAN_CMD1_DET_FAN_FAIL 0x80 /* enable fan_fail signal */
> +#define G762_REG_FAN_CMD1_DET_FAN_OOC 0x40 /* enable fan_out_of_control */
> +#define G762_REG_FAN_CMD1_OUT_MODE 0x20 /* out mode, pwm or dac */
> +#define G762_REG_FAN_CMD1_FAN_MODE 0x10 /* fan mode: close or open loop */
> +#define G762_REG_FAN_CMD1_CLK_DIV_ID1 0x08 /* clock divisor value */
> +#define G762_REG_FAN_CMD1_CLK_DIV_ID0 0x04
> +#define G762_REG_FAN_CMD1_PWM_POLARITY 0x02 /* pwm polarity */
> +#define G762_REG_FAN_CMD1_PULSE_PER_REV 0x01 /* pulse per fan revolution */
> +
> +#define G762_REG_FAN_CMD2_GEAR_MODE_1 0x08 /* fan gear mode */
> +#define G762_REG_FAN_CMD2_GEAR_MODE_0 0x04
> +#define G762_REG_FAN_CMD2_FAN_STARTV_1 0x02 /* fan startup voltage */
> +#define G762_REG_FAN_CMD2_FAN_STARTV_0 0x01
> +
> +#define G762_REG_FAN_STA_FAIL 0x02 /* fan fail */
> +#define G762_REG_FAN_STA_OOC 0x01 /* fan out of control */
> +
> +/* config register values */
> +#define OUT_MODE_PWM 1
> +#define OUT_MODE_DAC 0
> +
> +#define FAN_MODE_CLOSED_LOOP 1
> +#define FAN_MODE_OPEN_LOOP 0
> +
> +/* g762 default values: it is assumed that the fan is set for a 32KHz clock
> + * source, a fan clock divisor of 1 and two pulses per revolution. Default
> + * fan driving mode is linear mode (g762 also supports PWM mode) */
> +#define G762_DEFAULT_CLK 32768
> +#define G762_DEFAULT_FAN_CLK_DIV 1
> +#define G762_DEFAULT_PULSE_PER_REV 2
> +#define G762_DEFAULT_OUT_MODE 0
> +#define G762_DEFAULT_FAN_MODE 1
> +
> +/* register data is read (and cached) at most once per second */
> +#define G762_UPDATE_INTERVAL (HZ)
> +
> +/* extract pulse count per fan revolution value (2 or 4) from given
> + * FAN_CMD1 register value */
> +#define PULSE_FROM_REG(reg) \
> + (((reg & G762_REG_FAN_CMD1_PULSE_PER_REV)+1) << 1)
Always put ( ) around macro arguments.
> +
> +/* extract fan clock divisor (1, 2, 4 or 8) from given FAN_CMD1
> + * register value */
> +#define CLKDIV_FROM_REG(reg) \
> + (1 << ((reg & (G762_REG_FAN_CMD1_CLK_DIV_ID0 | \
> + G762_REG_FAN_CMD1_CLK_DIV_ID1)) >> 2))
> +
> +/* extract fan gear mode value (0, 1 or 2) from given FAN_CMD2
> + * register value */
> +#define GEARMODE_FROM_REG(reg) \
> + (1 << ((reg & (G762_REG_FAN_CMD2_GEAR_MODE_0 | \
> + G762_REG_FAN_CMD2_GEAR_MODE_1)) >> 2))
> +
> +struct g762_data {
> + struct i2c_client *client;
> + struct device *hwmon_dev;
> +
> + /* update mutex */
> + struct mutex update_lock;
> +
> + /* board specific parameters. */
> + u32 clk; /* default 32kHz */
> +
> + /* g762 register cache */
> + unsigned int valid:1;
Please use bool.
> + unsigned long last_updated; /* in jiffies */
> +
> + u8 set_cnt; /* RPM cmd in close loop control */
> + u8 act_cnt; /* formula: cnt = (CLK * 30)/(rpm * P) */
> + u8 fan_sta; /* bit 0: set when actual fan speed is more than
> + * 25% outside requested fan speed
> + * bit 1: set when no transition occurs on fan
> + * pin for 0.7s */
Extra line for */, please
> + u8 set_out; /* output voltage/PWM duty in open loop control */
> + u8 fan_cmd1; /* 0: FG_PLS_ID0 FG pulses count per revolution
> + * 0: 2 counts per revolution
> + * 1: 4 counts per revolution
> + * 1: PWM_POLARITY 1: negative_duty
> + * 0: positive_duty
> + * 2,3: [FG_CLOCK_ID0, FG_CLK_ID1]
> + * 00: Divide fan clock by 1
> + * 01: Divide fan clock by 2
> + * 10: Divide fan clock by 4
> + * 11: Divide fan clock by 8
> + * 4: FAN_MODE 1:close-loop, 0:open-loop
> + * 5: OUT_MODE 1:PWM, 0:DAC
> + * 6: DET_FAN_OOC enable "fan ooc" status
> + * 7: DET_FAN_FAIL enable "fan fail" status */
> + u8 fan_cmd2; /* 0,1: FAN_STARTV 0,1,2,3 -> 0,32,64,96 dac_code
> + * 2,3: FG_GEAR_MODE
> + * 00: div = 1
> + * 01: div = 2
> + * 10: div = 4
> + * 4: Mask ALERT# (g763 only) */
> +};
> +
> +/* sysfs PWM interface uses value from 0 to 255 when g762 FAN_SET_CNT register
> + * uses values from 255 (off) to 0 (full speed). */
> +#define PWM_FROM_CNT(cnt) (0xff-(cnt))
> +#define PWM_TO_CNT(pwm) (0xff-(pwm))
> +
> +/* Convert count value from fan controller register into fan speed RPM value.
> + * Note that the datasheet documents a basic formula. Influence of additional
> + * parameters have been infered from examples in the datasheet and tests:
> + * fan clock divisor, fan gear mode. */
/*
* Please follow CodingStyle for multi-line comments
*/
> +static inline unsigned int rpm_from_cnt(u8 cnt, u32 clk, u16 p,
tab after cnt ?
> + u8 clk_div, u8 gear_mode)
> +{
> + if (cnt == 0 || cnt == 0xff)
> + return 0;
> +
> + return (clk*30*(gear_mode+1))/(cnt*p*clk_div);
> +}
> +
> +/* Convert fan RPM value from sysfs into count value */
> +static inline unsigned char cnt_from_rpm(u32 rpm, u32 clk, u16 p,
> + u8 clk_div, u8 gear_mode)
> +{
> + return (rpm == 0) ? 0xff : (clk*30*(gear_mode+1))/(rpm*p*clk_div);
> +}
> +
> +#ifdef CONFIG_OF
> +static struct of_device_id g762_dt_match[] = {
> + { .compatible = "gmt,g762" },
> + { .compatible = "gmt,g763" },
> + { },
> +};
> +#endif
> +
> +static int g762_probe(struct i2c_client *client,
> + const struct i2c_device_id *id);
> +static int g762_remove(struct i2c_client *client);
> +
Please rearrange the code to not require forward declarations.
> +static struct i2c_driver g762_driver = {
> + .driver = {
> + .name = DRVNAME,
> + .owner = THIS_MODULE,
> + .of_match_table = of_match_ptr(g762_dt_match),
> + },
> + .probe = g762_probe,
> + .remove = g762_remove,
> + .id_table = g762_id,
> +};
> +
> +static inline int g762_read_value(struct i2c_client *client,
> + enum g762_regs reg)
> +{
> + return i2c_smbus_read_byte_data(client, reg);
> +}
> +
> +static inline int g762_write_value(struct i2c_client *client,
> + enum g762_regs reg, u16 value)
> +{
> + return i2c_smbus_write_byte_data(client, reg, value);
> +}
> +
> +/*
> + * sysfs attributes
> + */
> +
> +/* helper to grab and cache data, at most one time per second */
> +static struct g762_data *g762_update_client(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = i2c_get_clientdata(client);
> +
> + mutex_lock(&data->update_lock);
> + if (time_after(jiffies, data->last_updated + G762_UPDATE_INTERVAL) ||
> + unlikely(!data->valid)) {
> + data->set_cnt = g762_read_value(client, G762_REG_SET_CNT);
> + data->act_cnt = g762_read_value(client, G762_REG_ACT_CNT);
> + data->fan_sta = g762_read_value(client, G762_REG_FAN_STA);
> + data->set_out = g762_read_value(client, G762_REG_SET_OUT);
> + data->fan_cmd1 = g762_read_value(client, G762_REG_FAN_CMD1);
> + data->fan_cmd2 = g762_read_value(client, G762_REG_FAN_CMD2);
> +
> + data->last_updated = jiffies;
> + data->valid = 1;
> + }
> + mutex_unlock(&data->update_lock);
> +
> + return data;
> +}
> +
> +/* Read function for fan1_input sysfs file. Return current fan RPM value, or
> + * 0 if fan is out of control */
> +static ssize_t get_fan_rpm(struct device *dev, struct device_attribute *da,
> + char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> + unsigned int rpm = 0;
> +
> + mutex_lock(&data->update_lock);
> + /* reverse logic: fan out of control reporting is enabled low */
> + if (data->fan_sta & G762_REG_FAN_STA_OOC) {
> + rpm = rpm_from_cnt(data->act_cnt, data->clk,
> + PULSE_FROM_REG(data->fan_cmd1),
> + CLKDIV_FROM_REG(data->fan_cmd1),
> + GEARMODE_FROM_REG(data->fan_cmd2));
> + }
> + mutex_unlock(&data->update_lock);
> +
> + return sprintf(buf, "%u\n", rpm);
> +}
> +
> +/* Read function for pwm1_mode sysfs file. Get fan speed control
> + * mode i.e. pwm (1) or linear (0) */
> +static ssize_t get_pwm_mode(struct device *dev, struct device_attribute *da,
> + char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> + int pwm_mode;
> +
> + pwm_mode = (data->fan_cmd1 & G762_REG_FAN_CMD1_OUT_MODE) ? 1 : 0;
> +
> + return sprintf(buf, "%d\n", pwm_mode);
> +}
> +
> +static ssize_t do_set_pwm_mode(struct device *dev, u8 val)
Why ssize_t ?
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = g762_update_client(dev);
> +
> + mutex_lock(&data->update_lock);
> + switch (val) {
> + case OUT_MODE_PWM:
> + data->fan_cmd1 |= G762_REG_FAN_CMD1_OUT_MODE;
> + break;
> + case OUT_MODE_DAC: /* i.e. linear */
> + data->fan_cmd1 &= (u8) ~G762_REG_FAN_CMD1_OUT_MODE;
Unnecessary typecast. Several times.
> + break;
> + default:
> + mutex_unlock(&data->update_lock);
> + return -EINVAL;
> + }
> + g762_write_value(client, G762_REG_FAN_CMD1, data->fan_cmd1);
> + mutex_unlock(&data->update_lock);
> +
> + return val;
> +}
> +
> +/* Write function for pwm1_mode sysfs file. Set fan speed control
> + * mode as pwm (1) or linear (0) */
> +static ssize_t set_pwm_mode(struct device *dev, struct device_attribute *da,
> + const char *buf, size_t count)
> +{
> + unsigned long val;
> + ssize_t ret;
Why ssize_t ?
> +
> + if (kstrtoul(buf, 10, &val))
> + return -EINVAL;
> +
> + ret = do_set_pwm_mode(dev, (u8)val);
No overflow protection ? User writes 256, gets 0 ?
> + if (ret < 0)
> + return -EINVAL;
> +
> + return count;
> +}
> +
> +/* Read function for pwm1_freq sysfs file. */
> +static ssize_t get_pwm_freq(struct device *dev,
> + struct device_attribute *da, char *buf)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = i2c_get_clientdata(client);
> +
> + return sprintf(buf, "%d\n", data->clk);
> +}
> +
> +/* Write function for pwm1_freq sysfs file. */
> +static ssize_t set_pwm_freq(struct device *dev,
> + struct device_attribute *da,
> + const char *buf, size_t count)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = i2c_get_clientdata(client);
> + unsigned long val;
> +
> + if (kstrtoul(buf, 10, &val) || !val)
> + return -EINVAL;
> +
No limits, no overflow protection ?
> + mutex_lock(&data->update_lock);
> + data->clk = val;
> + mutex_unlock(&data->update_lock);
Now that lock is really unnecessary. What is clk for, anyway ? Doesn't it have
to be written into the chip ?
If it is a board specific constant, shouldn't it be provided with platform data
or device tree data instead ? What is the purpose of being able to write it at
runtime ?
> +
> + return count;
> +}
> +
> +/* Read function for fan1_div sysfs file. Get fan controller prescaler */
> +static ssize_t get_fan_clk_div(struct device *dev,
> + struct device_attribute *da, char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> +
> + return sprintf(buf, "%d\n", CLKDIV_FROM_REG(data->fan_cmd1));
> +}
> +
> +static ssize_t do_set_fan_clk_div(struct device *dev, u8 val)
Why ssize_t ?
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = g762_update_client(dev);
> +
> + mutex_lock(&data->update_lock);
> + switch (val) {
> + case 1:
> + data->fan_cmd1 &= (u8) ~G762_REG_FAN_CMD1_CLK_DIV_ID0;
> + data->fan_cmd1 &= (u8) ~G762_REG_FAN_CMD1_CLK_DIV_ID1;
Unnecessary typecasts.
> + break;
> + case 2:
> + data->fan_cmd1 |= G762_REG_FAN_CMD1_CLK_DIV_ID0;
> + data->fan_cmd1 &= (u8) ~G762_REG_FAN_CMD1_CLK_DIV_ID1;
> + break;
> + case 4:
> + data->fan_cmd1 &= (u8) ~G762_REG_FAN_CMD1_CLK_DIV_ID0;
> + data->fan_cmd1 |= G762_REG_FAN_CMD1_CLK_DIV_ID1;
> + break;
> + case 8:
> + data->fan_cmd1 |= G762_REG_FAN_CMD1_CLK_DIV_ID0;
> + data->fan_cmd1 |= G762_REG_FAN_CMD1_CLK_DIV_ID1;
> + break;
> + default:
> + mutex_unlock(&data->update_lock);
> + return -EINVAL;
> + }
> + g762_write_value(client, G762_REG_FAN_CMD1, (u16)data->fan_cmd1);
> + mutex_unlock(&data->update_lock);
> +
> + return val;
What is the purpose of returning val here (instead of returning 0 for no error) ?
> +}
> +
> +/* Write function for fan1_div file. Set fan controller prescaler */
> +static ssize_t set_fan_clk_div(struct device *dev,
> + struct device_attribute *da,
> + const char *buf, size_t count)
> +{
> + unsigned long val;
> + ssize_t ret;
Why ssize_t ?
> +
> + if (kstrtoul(buf, 10, &val))
> + return -EINVAL;
> +
No overflow protection ?
> + ret = do_set_fan_clk_div(dev, (u8) val);
> + if (ret < 0)
> + return -EINVAL;
> +
> + return count;
> +}
> +
> +/* Read function for fan1_gear_mode sysfs file. Get fan gear mode */
> +static ssize_t get_fan_gear_mode(struct device *dev,
> + struct device_attribute *da, char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> + u8 fan_gear_mode;
> +
> + fan_gear_mode = data->fan_cmd2 & (G762_REG_FAN_CMD2_GEAR_MODE_0 |
> + G762_REG_FAN_CMD2_GEAR_MODE_1);
> + fan_gear_mode = fan_gear_mode >> 2;
> +
> + return sprintf(buf, "%d\n", fan_gear_mode);
> +}
> +
> +static ssize_t do_set_fan_gear_mode(struct device *dev, u8 val)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = g762_update_client(dev);
> +
> + mutex_lock(&data->update_lock);
> + switch (val) {
> + case 0:
> + data->fan_cmd2 &= (u8) ~G762_REG_FAN_CMD2_GEAR_MODE_0;
> + data->fan_cmd2 &= (u8) ~G762_REG_FAN_CMD2_GEAR_MODE_1;
> + break;
> + case 1:
> + data->fan_cmd2 |= G762_REG_FAN_CMD2_GEAR_MODE_0;
> + data->fan_cmd2 &= (u8) ~G762_REG_FAN_CMD2_GEAR_MODE_1;
> + break;
> + case 2:
> + data->fan_cmd2 &= (u8) ~G762_REG_FAN_CMD2_GEAR_MODE_0;
> + data->fan_cmd2 |= G762_REG_FAN_CMD2_GEAR_MODE_1;
> + break;
> + default:
> + mutex_unlock(&data->update_lock);
> + return -EINVAL;
> + }
> + g762_write_value(client, G762_REG_FAN_CMD2, (u16)data->fan_cmd2);
> + mutex_unlock(&data->update_lock);
> +
> + return val;
> +}
> +
> +/* Write function for fan1_gear_mode sysfs file. Write fan gear mode */
> +static ssize_t set_fan_gear_mode(struct device *dev,
> + struct device_attribute *da,
> + const char *buf, size_t count)
> +{
> + unsigned long val;
> + ssize_t ret;
Why ssize_t ?
> +
> + if (kstrtoul(buf, 10, &val))
> + return -EINVAL;
> +
> + ret = do_set_fan_gear_mode(dev, (u8) val);
> + if (ret < 0)
> + return -EINVAL;
> +
> + return count;
> +}
> +
> +/* Read function for fan1_pulses. Returns either 2 or 4 */
> +static ssize_t get_fan_pulses(struct device *dev, struct device_attribute *da,
> + char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> +
> + return sprintf(buf, "%d\n", PULSE_FROM_REG(data->fan_cmd1));
> +}
> +
> +/* Set pulse per revolution value. Accepts either 2 or 4. */
> +static ssize_t do_set_fan_pulses(struct device *dev, u8 val)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = g762_update_client(dev);
> +
> + mutex_lock(&data->update_lock);
> + switch (val) {
> + case 2:
> + data->fan_cmd1 &= (u8) ~G762_REG_FAN_CMD1_PULSE_PER_REV;
> + break;
> + case 4:
> + data->fan_cmd1 |= G762_REG_FAN_CMD1_PULSE_PER_REV;
> + break;
> + default:
> + mutex_unlock(&data->update_lock);
> + return -EINVAL;
> + }
> + g762_write_value(client, G762_REG_FAN_CMD1, (u16)data->fan_cmd1);
> + mutex_unlock(&data->update_lock);
> +
> + return val;
> +}
> +
> +/* Write function for fan1_pulses. Accepts either 2 or 4 */
> +static ssize_t set_fan_pulses(struct device *dev, struct device_attribute *da,
> + const char *buf, size_t count)
> +{
> + unsigned long val;
> + ssize_t ret;
Why ssize_t ?
> +
> + if (kstrtoul(buf, 10, &val) || (val != 2 && val != 4))
> + return -EINVAL;
> +
> + ret = do_set_fan_pulses(dev, (u8) val);
> + if (ret < 0)
> + return -EINVAL;
> +
> + return count;
> +}
> +
> +/* Following documentation about hwmon's sysfs interface, a pwm1_enable node
> + * should accept followings:
> + *
> + * 0 : no fan speed control (i.e. fan at full speed)
> + * 1 : manual fan speed control enabled (use pwm[1-*]) (open-loop)
> + * 2+: automatic fan speed control enabled (use fan[1-*]_enable)(close-loop)
> + *
> + * but we do not accept 0 as "no-control" mode is not supported by g762,
> + * -EINVAL is returned in this case. */
> +static ssize_t get_speed_control_mode(struct device *dev,
> + struct device_attribute *da, char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> + int fan_mode;
> +
> + fan_mode = (data->fan_cmd1 & G762_REG_FAN_CMD1_FAN_MODE) ? 2 : 1;
> +
> + return sprintf(buf, "%d\n", fan_mode);
> +}
> +
> +static ssize_t do_set_speed_control_mode(struct device *dev, u8 val)
Why ssize_t ?
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = g762_update_client(dev);
> +
> + if (!val)
> + return -EINVAL;
> + val -= 1;
> +
> + mutex_lock(&data->update_lock);
> + switch (val) {
> + case FAN_MODE_CLOSED_LOOP:
> + data->fan_cmd1 |= G762_REG_FAN_CMD1_FAN_MODE;
> + break;
> + case FAN_MODE_OPEN_LOOP:
> + data->fan_cmd1 &= (u8) ~G762_REG_FAN_CMD1_FAN_MODE;
> + break;
> + default:
> + mutex_unlock(&data->update_lock);
> + return -EINVAL;
> + }
> +
> + g762_write_value(client, G762_REG_FAN_CMD1, data->fan_cmd1);
> + mutex_unlock(&data->update_lock);
> +
> + return val;
> +}
> +
> +static ssize_t set_speed_control_mode(struct device *dev,
> + struct device_attribute *da,
> + const char *buf, size_t count)
> +{
> + unsigned long val;
> + ssize_t ret;
And again ...
> +
> + if (kstrtoul(buf, 10, &val))
> + return -EINVAL;
> +
> + ret = do_set_speed_control_mode(dev, val);
> + if (ret < 0)
> + return -EINVAL;
> +
> + return count;
> +}
> +
> +/* Read function for pwm1_polarity (0: negative duty, 1: positive duty) */
> +static ssize_t get_pwm_polarity(struct device *dev, struct device_attribute *da,
> + char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> + u8 pwm_polarity;
> +
> + pwm_polarity = (data->fan_cmd1 & G762_REG_FAN_CMD1_PWM_POLARITY) >> 1;
> +
> + return sprintf(buf, "%d\n", pwm_polarity);
> +}
> +
> +/* Write function for pwm1_polarity (0: negative duty, 1: positive duty) */
> +static ssize_t set_pwm_polarity(struct device *dev, struct device_attribute *da,
> + const char *buf, size_t count)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = g762_update_client(dev);
> + unsigned long val;
> +
> + if (kstrtoul(buf, 10, &val))
> + return -EINVAL;
> +
> + mutex_lock(&data->update_lock);
> + switch (val) {
> + case 0: /* i.e. negative duty */
> + data->fan_cmd1 &= (u8) ~G762_REG_FAN_CMD1_PWM_POLARITY;
> + break;
> + case 1: /* i.e. positive duty */
> + data->fan_cmd1 |= G762_REG_FAN_CMD1_PWM_POLARITY;
> + break;
> + default:
> + mutex_unlock(&data->update_lock);
> + return -EINVAL;
> + }
> + g762_write_value(client, G762_REG_FAN_CMD1, data->fan_cmd1);
> + mutex_unlock(&data->update_lock);
> +
> + return count;
> +}
> +
> +/* Get/set the fan speed in open-loop mode using pwm1 sysfs file. Speed is
> + * given as a relative value from 0 to 255, where 255 is maximum speed. Note
> + * that this is done by writing directly to the chip's DAC, it won't change
> + * the closed loop speed set by fan1_target. Also note that due to rounding
> + * errors it is possible that you don't read back exactly the value you have
> + * set. */
> +static ssize_t get_pwm(struct device *dev, struct device_attribute *da,
> + char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> + int val;
> +
> + mutex_lock(&data->update_lock);
> + if (data->fan_cmd1 & G762_REG_FAN_CMD1_FAN_MODE) { /* closed-loop */
> + val = PWM_FROM_CNT(data->set_cnt);
> + } else { /* open-loop */
> + val = data->set_out;
> + }
> + mutex_unlock(&data->update_lock);
> +
> + return sprintf(buf, "%d\n", val);
> +}
> +
> +static ssize_t do_set_pwm(struct device *dev, u8 val)
and again.
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = g762_update_client(dev);
> +
> + mutex_lock(&data->update_lock);
> + if (data->fan_cmd1 & G762_REG_FAN_CMD1_FAN_MODE) { /* closed-loop */
> + val = PWM_TO_CNT(clamp_val(val, 0, 255));
> + data->set_cnt = val;
> + g762_write_value(client, G762_REG_SET_CNT, val);
> + } else { /* open-loop */
> + data->set_out = val;
> + g762_write_value(client, G762_REG_SET_OUT, val);
> + }
> + mutex_unlock(&data->update_lock);
> +
> + return val;
Why return val ? Why return anything in the first place ?
> +}
> +
> +static ssize_t set_pwm(struct device *dev, struct device_attribute *da,
> + const char *buf, size_t count)
> +{
> + unsigned long val;
> + ssize_t ret;
> +
> + if (kstrtoul(buf, 10, &val))
> + return -EINVAL;
> +
> + ret = do_set_pwm(dev, (u8)val);
> + if (ret < 0)
> + return -EINVAL;
> +
> + return count;
> +}
> +
> +/* Get/set the fan speed in closed-loop mode using fan1_target sysfs file. Speed
> + * is given as a rpm value, then G762 will automatically regulate the fan speed
> + * using pulses from fan tachometer.
> + *
> + * Refer to rpm_from_cnt implementation to get info about count number
> + * calculation.
> + *
> + * Also note that due to rounding errors it is possible that you don't read
> + * back exactly the value you have set. */
> +static ssize_t get_fan_target(struct device *dev, struct device_attribute *da,
> + char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> + unsigned int rpm;
> + ssize_t err;
> +
> + mutex_lock(&data->update_lock);
> + if (data->fan_cmd1 & G762_REG_FAN_CMD1_FAN_MODE) { /* closed-loop */
> + rpm = rpm_from_cnt(data->set_cnt, data->clk,
> + PULSE_FROM_REG(data->fan_cmd1),
> + CLKDIV_FROM_REG(data->fan_cmd1),
> + GEARMODE_FROM_REG(data->fan_cmd2));
> + err = sprintf(buf, "%u\n", rpm);
> + } else { /* open-loop */
> + err = -EINVAL;
> + }
> + mutex_unlock(&data->update_lock);
> +
> + return err;
> +}
> +
> +static ssize_t do_set_fan_target(struct device *dev, unsigned int val)
No longer commenting on ssize_t.
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = g762_update_client(dev);
> + ssize_t err;
> +
> + mutex_lock(&data->update_lock);
> + if (data->fan_cmd1 & G762_REG_FAN_CMD1_FAN_MODE) { /* closed-loop */
> + data->set_cnt = cnt_from_rpm(val, data->clk,
> + PULSE_FROM_REG(data->fan_cmd1),
> + CLKDIV_FROM_REG(data->fan_cmd1),
> + GEARMODE_FROM_REG(data->fan_cmd2));
> + g762_write_value(client, G762_REG_SET_CNT, data->set_cnt);
> + err = val;
> + } else {
> + err = -EINVAL;
> + }
> + mutex_unlock(&data->update_lock);
> +
> + return err;
> +}
> +
> +static ssize_t set_fan_target(struct device *dev, struct device_attribute *da,
> + const char *buf, size_t count)
> +{
> + unsigned int val;
> + ssize_t ret;
> +
> + if (sscanf(buf, "%u", &val) != 1)
> + return -EINVAL;
> +
> + ret = do_set_fan_target(dev, val);
> + if (ret < 0)
> + return -EINVAL;
> +
> + return count;
> +}
> +
> +/* read function for 'fan1_fault_detection' sysfs file */
> +static ssize_t get_fan_failure_detection(struct device *dev,
> + struct device_attribute *da,
> + char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> + unsigned int enabled;
> +
> + enabled = (data->fan_cmd1 & G762_REG_FAN_CMD1_DET_FAN_FAIL) ? 1 : 0;
> +
> + return sprintf(buf, "%u\n", enabled);
> +}
> +
> +/* enable (or disable) fan failure detection */
> +static ssize_t do_fan_failure_detection_toggle(struct device *dev,
> + unsigned int enable)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = g762_update_client(dev);
> +
> + mutex_lock(&data->update_lock);
> + switch (enable) {
> + case 0:
> + data->fan_cmd1 &= (u8) ~G762_REG_FAN_CMD1_DET_FAN_FAIL;
> + break;
> + case 1:
> + data->fan_cmd1 |= G762_REG_FAN_CMD1_DET_FAN_FAIL;
> + break;
> + default:
> + mutex_unlock(&data->update_lock);
> + return -EINVAL;
CodingStyle: Single return point.
> + }
> + g762_write_value(client, G762_REG_FAN_CMD1, data->fan_cmd1);
> + mutex_unlock(&data->update_lock);
> +
> + return enable;
> +}
> +
> +/* write function for 'fan1_fault_detection' sysfs file */
> +static ssize_t set_fan_failure_detection(struct device *dev,
> + struct device_attribute *da,
> + const char *buf, size_t count)
> +{
> + unsigned int val;
> + ssize_t ret;
> +
> + if (sscanf(buf, "%u", &val) != 1)
> + return -EINVAL;
> +
> + ret = do_fan_failure_detection_toggle(dev, val);
> + if (ret < 0)
> + return -EINVAL;
> +
> + return count;
> +}
> +
> +/* read function for fan1_fault sysfs file. */
> +static ssize_t get_fan_failure(struct device *dev, struct device_attribute *da,
> + char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> + unsigned int val;
> +
> + val = (data->fan_sta & G762_REG_FAN_STA_FAIL) ? 1 : 0;
> +
> + return sprintf(buf, "%u\n", val);
> +}
> +
> +/* read function for 'fan1_alarm_detection' sysfs file */
> +static ssize_t get_fan_ooc_detection(struct device *dev,
> + struct device_attribute *da,
> + char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> + unsigned int enabled;
> +
> + enabled = (data->fan_cmd1 & G762_REG_FAN_CMD1_DET_FAN_FAIL) ? 1 : 0;
> +
> + return sprintf(buf, "%u\n", enabled);
> +}
> +
> +/* enable (or disable) fan out of control detection */
> +static ssize_t do_fan_ooc_detection_toggle(struct device *dev,
> + unsigned int enable)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = g762_update_client(dev);
> +
> + mutex_lock(&data->update_lock);
> + switch (enable) {
> + case 0:
> + data->fan_cmd1 &= (u8) ~G762_REG_FAN_CMD1_DET_FAN_OOC;
> + break;
> + case 1:
> + data->fan_cmd1 |= G762_REG_FAN_CMD1_DET_FAN_OOC;
> + break;
> + default:
> + mutex_unlock(&data->update_lock);
> + return -EINVAL;
CodingStyle
> + }
> + g762_write_value(client, G762_REG_FAN_CMD1, data->fan_cmd1);
> + mutex_unlock(&data->update_lock);
> +
> + return enable;
> +}
> +
> +/* write function for 'fan1_alarm_detection' sysfs file */
> +static ssize_t set_fan_ooc_detection(struct device *dev,
> + struct device_attribute *da,
> + const char *buf, size_t count)
> +{
> + unsigned int val;
> + ssize_t ret;
> +
> + if (sscanf(buf, "%u", &val) != 1)
> + return -EINVAL;
> +
> + ret = do_fan_ooc_detection_toggle(dev, val);
> + if (ret < 0)
> + return -EINVAL;
> +
> + return count;
> +}
> +
> +/* read function for fan1_alarm sysfs file. */
> +static ssize_t get_fan_ooc(struct device *dev, struct device_attribute *da,
> + char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> + unsigned int val;
> +
> + /* ooc condition is enabled low */
> + val = (data->fan_sta & G762_REG_FAN_STA_OOC) ? 0 : 1;
> +
> + return sprintf(buf, "%u\n", val);
> +}
> +
> +/* Read function for fan1_startup_voltage */
> +static ssize_t get_fan_startup_voltage(struct device *dev,
> + struct device_attribute *da,
> + char *buf)
> +{
> + struct g762_data *data = g762_update_client(dev);
> + u8 val;
> +
> + val = data->fan_cmd2 & (G762_REG_FAN_CMD2_FAN_STARTV_1 |
> + G762_REG_FAN_CMD2_FAN_STARTV_0);
> +
> + return sprintf(buf, "%d\n", val);
> +}
> +
> +/* Write function for fan1_startup_voltage */
> +static ssize_t set_fan_startup_voltage(struct device *dev,
> + struct device_attribute *da,
> + const char *buf, size_t count)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct g762_data *data = g762_update_client(dev);
> + unsigned long val;
> +
> + if (kstrtoul(buf, 10, &val))
> + return -EINVAL;
> +
> + mutex_lock(&data->update_lock);
> + switch (val) {
> + case 0:
> + data->fan_cmd2 &= (u8) ~G762_REG_FAN_CMD2_FAN_STARTV_0;
> + data->fan_cmd2 &= (u8) ~G762_REG_FAN_CMD2_FAN_STARTV_1;
> + break;
> + case 1:
> + data->fan_cmd2 |= G762_REG_FAN_CMD2_FAN_STARTV_0;
> + data->fan_cmd2 &= (u8) ~G762_REG_FAN_CMD2_FAN_STARTV_1;
> + break;
> + case 2:
> + data->fan_cmd2 &= (u8) ~G762_REG_FAN_CMD2_FAN_STARTV_0;
> + data->fan_cmd2 |= G762_REG_FAN_CMD2_FAN_STARTV_1;
> + break;
> + case 3:
> + data->fan_cmd2 |= G762_REG_FAN_CMD2_FAN_STARTV_0;
> + data->fan_cmd2 |= G762_REG_FAN_CMD2_FAN_STARTV_1;
> + break;
> + default:
> + mutex_unlock(&data->update_lock);
> + return -EINVAL;
> + }
> + g762_write_value(client, G762_REG_FAN_CMD2, (u16)data->fan_cmd2);
> + mutex_unlock(&data->update_lock);
> +
> + return count;
> +}
> +
> +static DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, get_pwm, set_pwm);
> +static DEVICE_ATTR(pwm1_polarity, S_IWUSR | S_IRUGO,
> + get_pwm_polarity, set_pwm_polarity);
> +static DEVICE_ATTR(pwm1_mode, S_IWUSR | S_IRUGO,
> + get_pwm_mode, set_pwm_mode);
> +static DEVICE_ATTR(pwm1_enable, S_IWUSR | S_IRUGO,
> + get_speed_control_mode, set_speed_control_mode);
> +static DEVICE_ATTR(pwm1_freq, S_IWUSR | S_IRUGO,
> + get_pwm_freq, set_pwm_freq);
> +
> +static DEVICE_ATTR(fan1_input, S_IRUGO, get_fan_rpm, NULL);
> +static DEVICE_ATTR(fan1_alarm, S_IRUGO, get_fan_ooc, NULL);
> +static DEVICE_ATTR(fan1_alarm_detection, S_IWUSR | S_IRUGO,
> + get_fan_ooc_detection, set_fan_ooc_detection);
I don't know ... why not just enable it ?
I would suggest to look through the non-standard attributes to see which ones
are really needed at runtime. Seems to me they can (and should) all be
configuration values, set either through devicetree or platform data.
> +static DEVICE_ATTR(fan1_fault, S_IRUGO, get_fan_failure, NULL);
> +static DEVICE_ATTR(fan1_fault_detection, S_IWUSR | S_IRUGO,
> + get_fan_failure_detection, set_fan_failure_detection);
> +static DEVICE_ATTR(fan1_target, S_IWUSR | S_IRUGO,
> + get_fan_target, set_fan_target);
> +static DEVICE_ATTR(fan1_pulses, S_IWUSR | S_IRUGO,
> + get_fan_pulses, set_fan_pulses);
> +static DEVICE_ATTR(fan1_div, S_IWUSR | S_IRUGO,
> + get_fan_clk_div, set_fan_clk_div);
> +static DEVICE_ATTR(fan1_gear_mode, S_IWUSR | S_IRUGO,
> + get_fan_gear_mode, set_fan_gear_mode);
> +static DEVICE_ATTR(fan1_startup_voltage, S_IWUSR | S_IRUGO,
> + get_fan_startup_voltage, set_fan_startup_voltage);
> +
> +/* Driver data */
> +static struct attribute *g762_attributes[] = {
> + &dev_attr_fan1_input.attr,
> + &dev_attr_fan1_alarm.attr,
> + &dev_attr_fan1_alarm_detection.attr,
> + &dev_attr_fan1_fault.attr,
> + &dev_attr_fan1_fault_detection.attr,
> + &dev_attr_fan1_target.attr,
> + &dev_attr_fan1_pulses.attr,
> + &dev_attr_fan1_div.attr,
> + &dev_attr_fan1_gear_mode.attr,
> + &dev_attr_fan1_startup_voltage.attr,
> + &dev_attr_pwm1.attr,
> + &dev_attr_pwm1_polarity.attr,
> + &dev_attr_pwm1_mode.attr,
> + &dev_attr_pwm1_enable.attr,
> + &dev_attr_pwm1_freq.attr,
> + NULL
> +};
> +
> +static const struct attribute_group g762_group = {
> + .attrs = g762_attributes,
> +};
> +
> +static int g762_probe(struct i2c_client *client, const struct i2c_device_id *id)
> +{
> + u32 pwm_freq, fan_clk_div, fan_pulses, pwm_mode, fan_target, pwm_enable;
> + struct g762_data *data;
> + int err;
> +
> + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
> + return -ENODEV;
> +
> + data = devm_kzalloc(&client->dev, sizeof(struct g762_data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> + i2c_set_clientdata(client, data);
> +
> + data->client = client;
> + mutex_init(&data->update_lock);
> +
> + /* Setup default configuration for now. Those may get modified below
> + * in CONFIG_OF-protected block (via .dts file). Final values will
> + * then be pushed to the device */
> + pwm_freq = G762_DEFAULT_CLK;
> + fan_clk_div = G762_DEFAULT_FAN_CLK_DIV;
> + fan_pulses = G762_DEFAULT_PULSE_PER_REV;
> + pwm_mode = G762_DEFAULT_OUT_MODE;
> + pwm_enable = G762_DEFAULT_FAN_MODE + 1; /* shift w/ sysfs interface */
> + fan_target = 0xffffffff; /* dummy value */
> +
> + /* Enable fan protection and fan fail detection by default */
> + do_fan_ooc_detection_toggle(&client->dev, 1);
> + do_fan_failure_detection_toggle(&client->dev, 1);
> +
> +#ifdef CONFIG_OF
It would be better to have a separate function for this.
> + if (client->dev.of_node) {
> + const __be32 *prop;
> + int len;
> +
> + prop = of_get_property(client->dev.of_node, "pwm_freq", &len);
> + if (prop && len == sizeof(u32)) {
> + pwm_freq = be32_to_cpu(prop[0]);
> + dev_info(&client->dev, "found pwm_freq (%d)\n", pwm_freq);
> + }
> +
> + prop = of_get_property(client->dev.of_node, "fan_div", &len);
> + if (prop && len == sizeof(u32)) {
> + fan_clk_div = be32_to_cpu(prop[0]);
> + dev_info(&client->dev, "found fan_div (%d)\n",
> + fan_clk_div);
> + }
> +
> + prop = of_get_property(client->dev.of_node, "fan_pulses", &len);
> + if (prop && len == sizeof(u32)) {
> + fan_pulses = be32_to_cpu(prop[0]);
> + dev_info(&client->dev, "found fan_pulses (%d)\n",
> + fan_pulses);
> + }
> +
> + prop = of_get_property(client->dev.of_node, "pwm_mode", &len);
> + if (prop && len == sizeof(u32)) {
> + pwm_mode = be32_to_cpu(prop[0]);
> + dev_info(&client->dev, "found pwm_mode (%d)\n",
> + pwm_mode);
> + }
> +
> + prop = of_get_property(client->dev.of_node, "fan_target", &len);
> + if (prop && len == sizeof(u32)) {
> + fan_target = be32_to_cpu(prop[0]);
> + dev_info(&client->dev, "found fan_target (%d)\n",
> + fan_target);
> + }
> +
> + prop = of_get_property(client->dev.of_node, "pwm_enable", &len);
> + if (prop && len == sizeof(u32)) {
> + pwm_enable = be32_to_cpu(prop[0]);
> + dev_info(&client->dev, "found pwm_enable (%d)\n",
> + pwm_enable);
> + }
> + }
> +#endif
> +
> + /* Now, let's set final fan out mode (pwm or linear), loop mode (closed
> + * or open loop), clock freq, pulse per rev, fan clock div, fan target
> + * value, and speed control method (closed or open loop) */
> + err = do_set_pwm_mode(&client->dev, pwm_mode);
> + if (err < 0) {
> + dev_info(&client->dev, "unable to set pwm_mode (%d)\n",
> + pwm_mode);
> + }
> +
> + err = do_set_speed_control_mode(&client->dev, pwm_enable);
> + if (err < 0) {
> + dev_info(&client->dev, "unable to set pwm_enable (%d)\n",
> + pwm_enable);
None of those are errors ?
> + }
> +
> + err = do_set_fan_clk_div(&client->dev, fan_clk_div);
> + if (err < 0) {
> + dev_info(&client->dev, "unable to set fan_clk_div (%d)\n",
> + fan_clk_div);
> + }
> +
> + err = do_set_fan_pulses(&client->dev, fan_pulses);
> + if (err < 0) {
> + dev_info(&client->dev, "unable to set fan_pulses (%d)\n",
> + fan_pulses);
> + }
> +
> + data->clk = pwm_freq;
> +
> + if (fan_target != 0xffffffff) {
> + err = do_set_fan_target(&client->dev, fan_target);
> + if (err < 0) {
> + dev_info(&client->dev, "unable to set fan_target (%d)\n",
> + fan_target);
> + }
> + }
> +
> + /* Register sysfs hooks */
> + err = sysfs_create_group(&client->dev.kobj, &g762_group);
> + if (err)
> + return err;
> + data->hwmon_dev = (struct device *)hwmon_device_register(&client->dev);
What is this typecast about ?
> + if (IS_ERR(data->hwmon_dev)) {
> + err = PTR_ERR(data->hwmon_dev);
> + sysfs_remove_group(&client->dev.kobj, &g762_group);
> + return err;
> + }
> +
> + dev_info(&data->client->dev, "device successfully initialized\n");
> +
> + return 0;
> +}
> +
> +static int g762_remove(struct i2c_client *client)
> +{
> + struct g762_data *data = i2c_get_clientdata(client);
> +
> + hwmon_device_unregister(data->hwmon_dev);
> + sysfs_remove_group(&client->dev.kobj, &g762_group);
> +
> + dev_info(&data->client->dev, "device successfully removed\n");
> + return 0;
> +}
> +
> +module_i2c_driver(g762_driver);
> +
> +MODULE_AUTHOR("Olivier Mouchet <olivier.mouchet at gmail.com>");
> +MODULE_DESCRIPTION("GMT G762 driver");
> +MODULE_LICENSE("GPL");
> --
> 1.7.10.4
>
>
More information about the linux-arm-kernel
mailing list