[PATCH 5/5] ARM: at91: add Acme Systems Fox G20 board

[Nicolas Ferre]

From: Douglas Gilbert <dgilbert at interlog.com>

Signed-off-by: Douglas Gilbert <dgilbert at interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre at atmel.com>
---
 arch/arm/boot/dts/Makefile        |   1 +
 arch/arm/boot/dts/at91-foxg20.dts | 166 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 167 insertions(+)
 create mode 100644 arch/arm/boot/dts/at91-foxg20.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b07f162..914fe65 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_AT91) += at91sam9263ek.dtb
 dtb-$(CONFIG_ARCH_AT91) += tny_a9263.dtb
 dtb-$(CONFIG_ARCH_AT91) += usb_a9263.dtb
 # sam9g20
+dtb-$(CONFIG_ARCH_AT91) += at91-foxg20.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9g20ek.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9g20ek_2mmc.dtb
 dtb-$(CONFIG_ARCH_AT91) += kizbox.dtb
diff --git a/arch/arm/boot/dts/at91-foxg20.dts b/arch/arm/boot/dts/at91-foxg20.dts
new file mode 100644
index 0000000..7d24ef7
--- /dev/null
+++ b/arch/arm/boot/dts/at91-foxg20.dts
@@ -0,0 +1,166 @@
+/*
+ * at91-foxg20.dts - Device Tree file for Acme Systems FoxG20 board
+ *
+ * Based on DT files for at91sam9g20ek evaluation board (AT91SAM9G20 SoC)
+ *
+ * Copyright (C) 2013 Douglas Gilbert <dgilbert at interlog.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+/include/ "at91sam9g20.dtsi"
+
+/ {
+	model = "Acme Systems FoxG20";
+	compatible = "acme,foxg20", "atmel,at91sam9g20", "atmel,at91sam9";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait";
+	};
+
+	memory {
+		reg = <0x20000000 0x4000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		main_clock: clock at 0 {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <18432000>;
+		};
+	};
+
+	ahb {
+		apb {
+			usb1: gadget at fffa4000 {
+				atmel,vbus-gpio = <&pioC 6 0>;
+				status = "okay";
+			};
+
+			mmc0: mmc at fffa8000 {
+				pinctrl-0 = <
+					&pinctrl_mmc0_clk
+					&pinctrl_mmc0_slot1_cmd_dat0
+					&pinctrl_mmc0_slot1_dat1_3>;
+				status = "okay";
+				slot at 1 {
+					reg = <1>;
+					bus-width = <4>;
+				};
+			};
+
+			usart0: serial at fffb0000 {
+				pinctrl-0 =
+					<&pinctrl_usart0
+					 &pinctrl_usart0_rts
+					 &pinctrl_usart0_cts
+					>;
+				status = "okay";
+			};
+
+			usart1: serial at fffb4000 {
+				status = "okay";
+			};
+
+			usart2: serial at fffb8000 {
+				status = "okay";
+			};
+
+			macb0: ethernet at fffc4000 {
+				phy-mode = "rmii";
+				status = "okay";
+			};
+
+			spi0: spi at fffc8000 {
+				cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
+				mtd_dataflash at 0 {
+					compatible = "atmel,at45", "atmel,dataflash";
+					spi-max-frequency = <50000000>;
+					reg = <1>;
+				};
+				status = "disabled";
+			};
+
+			usart3: serial at fffd0000 {
+				status = "okay";
+			};
+
+			uart0: serial at fffd4000 {
+				status = "okay";
+			};
+
+			uart1: serial at fffd8000 {
+				status = "okay";
+			};
+
+			dbgu: serial at fffff200 {
+				status = "okay";
+			};
+
+			pinctrl at fffff400 {
+				board {
+					pinctrl_pck0_as_mck: pck0_as_mck {
+						atmel,pins =
+							<2 1 0x2 0x0>;	/* PC1 periph B */
+					};
+				};
+
+				mmc0_slot1 {
+					pinctrl_board_mmc0_slot1: mmc0_slot1-board {
+						atmel,pins =
+							<2 9 0x0 0x5>;	/* PC9 gpio CD pin pull up and deglitch */
+					};
+				};
+
+				i2c0 {
+					pinctrl_i2c0: i2c0-0 {
+						atmel,pins =
+							<0 23 0x1 0x2	/* TWD (SDA) PA23 periph A, open drain */
+							 0 24 0x1 0x2>;	/* TWCK (SCL) PA24 periph A, open drain */
+					};
+				};
+			};
+
+			watchdog at fffffd40 {
+				status = "okay";
+			};
+		};
+
+		usb0: ohci at 00500000 {
+			num-ports = <2>;
+			status = "okay";
+		};
+	};
+
+	i2c at 0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c0>;
+		i2c-gpio,delay-us = <5>;	/* ~85 kHz */
+		status = "okay";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* red LED marked "PC7" near mini USB (device) receptacle */
+		user_led {
+			label = "user_led";
+			gpios = <&pioC 7 0>;	/* PC7 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		btn {
+			label = "Button";
+			gpios = <&pioC 4 1>;
+			linux,code = <0x103>;
+			gpio-key,wakeup;
+		};
+	};
+};
-- 
1.8.0