[PATCH] ARM: dts: omap3-beagle-xm: Add USB Host support for Rev Ax/Bx

[Tony Lindgren]

* Igor Grinberg <grinberg at compulab.co.il> [130417 05:31]:
> On 04/17/13 11:38, Roger Quadros wrote:
> > On 04/17/2013 10:56 AM, Igor Grinberg wrote:
> >> On 04/17/13 04:30, Robert Nelson wrote:
> >>> On Tue, Apr 16, 2013 at 7:52 PM, Tony Lindgren <tony at atomide.com> wrote:
> >>>> * Roger Quadros <rogerq at ti.com> [130415 05:44]:
> >>>>> On 04/15/2013 03:35 PM, Roger Quadros wrote:
> >>>>>> Provide RESET and Power regulators for the USB PHY,
> >>>>>> the USB Host port mode and the PHY device.
> >>>>>>
> >>>>>> Also provide pin multiplexer information for USB host
> >>>>>> pins.
> >>>>>>
> >>>>>> This will not work for Rev Cx boards because of reversed logic
> >>>>>> for USB_POWER_Enable.
> >>>>>>
> >>>>>> CC: Benoît Cousson <b-cousson at ti.com>
> >>>>>> Signed-off-by: Roger Quadros <rogerq at ti.com>
> >>>>>> ---
> >>>>>>  arch/arm/boot/dts/omap3-beagle-xm.dts |   62 +++++++++++++++++++++++++++++++++
> >>>>>>  1 files changed, 62 insertions(+), 0 deletions(-)
> >>>>>>
> >>>>>> diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
> >>>>>> index 5a31964..d394c51 100644
> >>>>>> --- a/arch/arm/boot/dts/omap3-beagle-xm.dts
> >>>>>> +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
> >>>>>> @@ -57,6 +57,60 @@
> >>>>>>             ti,mcbsp = <&mcbsp2>;
> >>>>>>             ti,codec = <&twl_audio>;
> >>>>>>     };
> >>>>>> +
> >>>>>> +   /* HS USB Port 2 RESET */
> >>>>>> +   hsusb2_reset: hsusb2_reset_reg {
> >>>>>> +           compatible = "regulator-fixed";
> >>>>>> +           regulator-name = "hsusb2_reset";
> >>>>>> +           regulator-min-microvolt = <3300000>;
> >>>>>> +           regulator-max-microvolt = <3300000>;
> >>>>>> +           gpio = <&gpio5 19 0>;   /* gpio_147 */
> >>>>>> +           startup-delay-us = <70000>;
> >>>>>> +           enable-active-high;
> >>>>>> +   };
> >>>>>> +
> >>>>>> +   /* HS USB Port 2 Power */
> >>>>>> +   hsusb2_power: hsusb2_power_reg {
> >>>>>> +           compatible = "regulator-fixed";
> >>>>>> +           regulator-name = "hsusb2_vbus";
> >>>>>> +           regulator-min-microvolt = <3300000>;
> >>>>>> +           regulator-max-microvolt = <3300000>;
> >>>>>> +           gpio = <&twl_gpio 18 0>;        /* GPIO LEDA */
> >>>>>> +           startup-delay-us = <70000>;
> >>>>>> +           enable-active-high;     /* FIXME: active-low for Rev. C */
> >>>>>
> >>>>> Benoit & Tony,
> >>>>>
> >>>>> Any ideas how to tackle the reversed logic for Rev. C boards?
> >>>>
> >>>> Sounds like we need a shared omap3-beage.dtsi, then omap3-beagle-xm.dts
> >>>> and omap3-beagle-rev-c.dts. Then xm and rev-c can both include the
> >>>
> >>> Bike-sheding, but we might want to make that "omap3-beagle-xmc.dts" as
> >>> there is the "rev c" variant of the original beagle...
> >>>
> >>> It's too bad we can't read the 3 gpio pin states in the device tree
> >>> and make a decision.
> >>
> >> I would recommend to move the detection to the boot loader and
> >> adjust the DT blob at run time (in the boot loader).
> >> This way, we will not need to deal with all the (sub)revision stuff.
> >>
> >>
> > Moving the detection to bootloader is fine, but modifying the DT at
> > runtime would create a debug/maintenance issue. Instead it could just
> > pick one of the .DTBs and pass it to kernel.
> 
> Like this will not create create any debug/maintenance issues.... ;-)
> We have no problem with debug, as all the DT nodes can be seen in
> both U-Boot (with fdt commands) and Linux through procfs...
> 
> I've just dropped my 2 cents and I don't really insist...

The dynamic configuration from the bootloader can also be done too, I
don't think they are mutually exclusive. 
 
> > Since most users will be using rev-c, I think we should keep the original
> > file 'omap3-beagle-xm.dts" as it is for rev-c boards.
> > I can just create a new dts file for Revisions A and B that will be
> > like so.
> > 
> > +++ b/arch/arm/boot/dts/omap3-beagle-xm-ab.dts
> > @@ -0,0 +1,6 @@
> > +/include/ "omap3-beagle-xm.dts"
> > +
> > +/* On Rev A/B USBHOST_PWR_EN is active high */
> > +&hsusb2_power {
> > +       enable-active-high;
> > +};
> > 
> > Since omap3-beagle and omap3-beagle-xm use different SoC versions and have
> > quite many differences, I don't think it is a good idea to create a common
> > file between the two.

Sounds good to me. But please also add the revision info to the compatible
flags for both .dts files.

Regards,

Tony