[PATCH 4/8] dmaengine: ste_dma40: Do not configure channels during an channel allocation

[Lee Jones]

On Fri, 12 Apr 2013, Rabin Vincent wrote:

> 2013/4/9 Lee Jones <lee.jones at linaro.org>:
> > diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
> > index 2a0a9d4..9e423ad 100644
> > --- a/drivers/dma/ste_dma40.c
> > +++ b/drivers/dma/ste_dma40.c
> > @@ -2463,16 +2463,10 @@ static int d40_alloc_chan_resources(struct dma_chan *chan)
> >         }
> >
> >         pm_runtime_get_sync(d40c->base->dev);
> > -       /* Fill in basic CFG register values */
> > -       d40_phy_cfg(&d40c->dma_cfg, &d40c->src_def_cfg,
> > -                   &d40c->dst_def_cfg, chan_is_logical(d40c));
> >
> >         d40_set_prio_realtime(d40c);
> >
> >         if (chan_is_logical(d40c)) {
> > -               d40_log_cfg(&d40c->dma_cfg,
> > -                           &d40c->log_def.lcsp1, &d40c->log_def.lcsp3);
> > -
> >                 if (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM)
> >                         d40c->lcpa = d40c->base->lcpa_base +
> >                                 d40c->dma_cfg.src_dev_type * D40_LCPA_CHAN_SIZE;
> > @@ -2487,14 +2481,6 @@ static int d40_alloc_chan_resources(struct dma_chan *chan)
> >                  d40c->phy_chan->num,
> >                  d40c->dma_cfg.use_fixed_channel ? ", fixed" : "");
> >
> > -
> > -       /*
> > -        * Only write channel configuration to the DMA if the physical
> > -        * resource is free. In case of multiple logical channels
> > -        * on the same physical resource, only the first write is necessary.
> > -        */
> > -       if (is_free_phy)
> > -               d40_config_write(d40c);
> 
> This function does basic initial configuration which is linked to
> whether the channel is pysical or logical -- something that is not being
> allowed to be runtime configured, so the place to call this function is
> here.  Furthermore, it clears the SSLNK/SDLNK which has to be done here,
> when the phy channel is first allocated.

Okay, I see what you're saying.

So I need to devise another way, as this function cannot be called
here either. Using the dmaengine API, allocating a channel and
configuring it are to be completed using different calls. Using the
API correctly, there is no way the driver can setup the channel
with all of the relevant information during allocation time.

The steps are as follows:

dma_request_channel() - here we only allot a channel number and
                        allocate the appropriate resources for the
			channel.

dma_slave_config()    - this is where we're meant to configure the
                        channel, so d40_config_write() needs to be
			called here, as only dma_slave_config() will
			carry the information required so as
			d40_*_cfg() can make the correct decisions.

At the moment calling dma_slave_config() ends up calling
d40_set_runtime_config(), which, taking into consideration what you've
been saying about possibly cutting off other logical channels, is
probably not what we want. I'll take a look at the dmaengine API and
see if there's a more appropriate way to do that.

Thanks again for your input Rabin, it's invaluable.

Kind regards,
Lee		

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog