[PATCH V2 6/7] ARM: EXYNOS5: Add the bus clock for FIMD

[Jingoo Han]

On Tuesday, July 24, 2012 10:56 AM, Joonyoung Shim Wrote:
> 
> On 07/24/2012 08:55 AM, Jingoo Han wrote:
> > On Tuesday, July 24, 2012 8:46 AM, Joonyoung Shim Wrote:
> >> On 07/24/2012 08:14 AM, Jingoo Han wrote:
> >>> On Monday, July 23, 2012 6:55 PM, Joonyoung Shim wrote:
> >>>> Hi, Jingoo.
> >>>>
> >>>> On 07/23/2012 05:34 PM, Joonyoung Shim wrote:
> >>>>> On 07/18/2012 02:57 PM, Leela Krishna Amudala wrote:
> >>>>>> This patch adds the bus clock for FIMD and changes
> >>>>>> the device name for lcd clock
> >>>>> Please refer below patch for exynos4.
> >>>>>
> >>>>> http://lists.linaro.org/pipermail/linaro-dev/2011-December/008872.html
> >>>>>
> >>>>>> Signed-off-by: Leela Krishna Amudala <l.krishna at samsung.com>
> >>>>>> ---
> >>>>>>     arch/arm/mach-exynos/clock-exynos5.c |    7 ++++++-
> >>>>>>     1 files changed, 6 insertions(+), 1 deletions(-)
> >>>>>>
> >>>>>> diff --git a/arch/arm/mach-exynos/clock-exynos5.c
> >>>>>> b/arch/arm/mach-exynos/clock-exynos5.c
> >>>>>> index 774533c..f001876 100644
> >>>>>> --- a/arch/arm/mach-exynos/clock-exynos5.c
> >>>>>> +++ b/arch/arm/mach-exynos/clock-exynos5.c
> >>>>>> @@ -634,6 +634,11 @@ static struct clk exynos5_init_clocks_off[] = {
> >>>>>>             .enable        = exynos5_clk_ip_disp1_ctrl,
> >>>>>>             .ctrlbit    = (1 << 3),
> >>>>>>         }, {
> >>>>>> +        .name           = "fimd",
> >>>>>> +        .devname        = "exynos5-fb",
> >>>>>> +        .enable         = exynos5_clk_ip_disp1_ctrl,
> >>>>>> +        .ctrlbit        = (1 << 0),
> >>>>>> +    }, {
> >>>> With this patch, it causes below error at the DP driver because fimd
> >>>> clock is disabled.
> >>>>
> >>>> [    0.210000] exynos-dp exynos-dp: Timeout of video streamclk ok
> >>>> [    0.210000] exynos-dp exynos-dp: unable to config video
> >>>> [    0.210000] exynos-dp: probe of exynos-dp failed with error -110
> >>>>
> >>>> I wonder fimd clock has any dependency with DP
> >>> FIMD pixel clock is necessary to enable DP.
> >> So then, i think DP driver also should control FIMD pixel clock.
> >> Do you have any patch or plan for it?
> > Um, I don't think so.
> > Because, DP cannot work by itself.
> > In order to use DP, FIMD should be enabled.
> >
> > If FIMD is enabled, FIMD pixel clock is enabled;
> > therefore, DP driver does not need to control FIMD pixel clock.
> 
> Why does DP driver have FIMD driver dependency? Also for this, it needs
> FIMD driver is probed earlier then DP driver.  We cannot decide driver
> probe order if they are same level drivers and itself is weird
> condition.  Although there is hardware dependency, DP and FIMD driver
> don't have any code relations. They are each other drivers. But DP
> needs FIMD pixel clock and because the clock can be control at the
> several drivers and the clock framework exists for that, then i think
> it's better DP driver also control FIMD pixel clock.
> 
> >
> > In my opinion, adding config dependency would be better, such as FB_S3C or DRM_EXYNOS_FIMD.
> 
> I think this is not solution. How do you ensure FIMD driver is probed
> earlier than DP driver? Even if it's possible, when FIMD driver only
> controls pixel clock, DP driver will execute any operations regardless
> status of FIMD pixel clock, so if FIMD driver turns off pixel clock,
> then DP will occur any error.

late_initcall can ensure DP driver is probed later.

As you mentioned, DP controller does not work without FIMD controller.
Because FIMD controller should provide video data and video clock to DP controller.
In this case, adding config dependency would be good.

If FIMD driver turns off pixel clock, DP should be turned off too.
Currently, FB FIMD driver turns off pixel clock in remove() and suspend().
So, FIMD driver is enabled, DP will not occur any error on pixel clock.