[PATCH v3 6/6] mmc: dw_mmc: add samsung exynos5250 specific extentions
Seungwon Jeon
tgih.jun at samsung.com
Fri Jul 20 06:38:58 EDT 2012
July 20, 2012, Thomas Abraham <thomas.abraham at linaro.org> wrote:
> On 19 July 2012 09:21, Seungwon Jeon <tgih.jun at samsung.com> wrote:
> > Hi,
> >
> > This version does not seems to consider previous reviews fully.
> > Could you check the comments below?
>
> I did try to address all the comments. I will check again and resubmit
> if I have missed anything.
>
> >
> > July 12, 2012, Thomas Abraham <thomas.abraham at linaro.org> wrote:
> >> The instantiation of the Synopsis Designware controller on Exynos5250
> >> include extension for SDR and DDR specific tx/rx phase shift timing
> >> and CIU internal divider. In addition to that, the option to skip the
> >> command hold stage is also introduced. Add support for these Exynos5250
> >> specfic extenstions.
> >>
> >> Signed-off-by: Abhilash Kesavan <a.kesavan at samsung.com>
> >> Signed-off-by: Thomas Abraham <thomas.abraham at linaro.org>
> >> ---
> >> .../devicetree/bindings/mmc/synposis-dw-mshc.txt | 38 ++++++++++++++++++-
> >> drivers/mmc/host/dw_mmc-pltfm.c | 15 +++++++
> >> drivers/mmc/host/dw_mmc.c | 40 +++++++++++++++++++-
> >> drivers/mmc/host/dw_mmc.h | 14 +++++++
> >> include/linux/mmc/dw_mmc.h | 6 +++
> >> 5 files changed, 110 insertions(+), 3 deletions(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt
> >> b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt
> >> index 3acd6c9..69d78c1 100644
> >> --- a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt
> >> +++ b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt
> >> @@ -7,6 +7,8 @@ Required Properties:
> >>
> >> * compatible: should be one of the following
> >> - snps,dw-mshc: for controllers compliant with synopsis dw-mshc.
> >> + - samsung,exynos5250-dw-mshc: for controllers with Samsung
> >> + Exynos5250 specific extentions.
> >>
> >> * reg: physical base address of the dw-mshc controller and size of its memory
> >> region.
> >> @@ -74,13 +76,45 @@ Aliases:
> >> the following format 'mshc{n}' where n is a unique number for the alias.
> >>
> >>
> >> +Samsung Exynos4/5 specific properties:
> >> +
> >> +Some of the variants of Exynos4 (such as Exynos4412) and Exynos5 SoC's
> >> +includes few extensions to the Synopsis Designware Mobile Storage Host
> >> +Controller. The following properties are used to describe those extensions.
> >> +
> >> +* samsung,dw-mshc-sdr-timing: Specifies the value of CUI clock divider, CIU
> >> + clock phase shift value in transmit mode and CIU clock phase shift value in
> >> + receive mode for single data rate mode operation. Refer notes of the valid
> >> + values below.
> >> +
> >> +* samsung,dw-mshc-ddr-timing: Specifies the value of CUI clock divider, CIU
> >> + clock phase shift value in transmit mode and CIU clock phase shift value in
> >> + receive mode for double data rate mode operation. Refer notes of the valid
> >> + values below. The order of the cells should be
> >> +
> >> + - First Cell: CIU clock divider value (applicable only for Exynos5
> >> + SoC's, should be zero for Exynos4 SoC's)
> >> + - Second Cell: CIU clock phase shift value for tx mode.
> >> + - Third Cell: CIU clock phase shift value for rx mode.
> >> +
> >> + Valid values for SDR and DDR CIU clock timing for Exynos5250:
> >> +
> >> + - valid values for CIU clock divider, tx phase shift and rx phase shift
> >> + is 0 to 7.
> >> +
> >> + - When CIU clock divider value is set to 3, all possible 8 phase shift
> >> + values can be used.
> >> +
> >> + - If CIU clock divider value is 0 (that is divide by 1), both tx and rx
> >> + phase shift clocks should be 0.
> >> +
> >> Example:
> >>
> >> The MSHC controller node can be split into two portions, SoC specific and
> >> board specific portions as listed below.
> >>
> >> dwmmc0 at 12200000 {
> >> - compatible = "snps,dw-mshc";
> >> + compatible = "samsung,exynos5250-dw-mshc";
> >> reg = <0x12200000 0x1000>;
> >> interrupts = <0 75 0>;
> >> #address-cells = <1>;
> >> @@ -94,6 +128,8 @@ Example:
> >> no-write-protect;
> >> fifo-depth = <0x80>;
> >> card-detect-delay = <200>;
> >> + samsung,dw-mshc-sdr-timing = <2 3 3>;
> >> + samsung,dw-mshc-ddr-timing = <1 2 3>;
> >>
> >> slot at 0 {
> >> reg = <0>;
> >> diff --git a/drivers/mmc/host/dw_mmc-pltfm.c b/drivers/mmc/host/dw_mmc-pltfm.c
> >> index 8d24f6d..900f412 100644
> >> --- a/drivers/mmc/host/dw_mmc-pltfm.c
> >> +++ b/drivers/mmc/host/dw_mmc-pltfm.c
> >> @@ -27,9 +27,24 @@ static struct dw_mci_drv_data synopsis_drv_data = {
> >> .ctrl_type = DW_MCI_TYPE_SYNOPSIS,
> >> };
> >>
> >> +static unsigned long exynos5250_dwmmc_caps[4] = {
> >> + MMC_CAP_UHS_DDR50 | MMC_CAP_1_8V_DDR |
> >> + MMC_CAP_8_BIT_DATA | MMC_CAP_CMD23,
> >> + MMC_CAP_CMD23,
> >> + MMC_CAP_CMD23,
> >> + MMC_CAP_CMD23,
> >> +};
> >> +
> > Kyungmin Park has already pointed .
> > It's not still proper place for board specific caps.
> > If I'm incorrect, please let me know.
> > And why MMC_CAP_CMD23 is default caps for all channel of hosts?
>
> The cap listed above are specifying controller capabilities for dw-mmc
> controllers on Exynos5 SoC. They are not board specific caps. All the
> Exynos5 dw-mmc controllers can support MMC_CAP_CMD23 cap and hence, it
> has been listed for all the controllers. Please let me know if you
> feel there is any change required here.
MMC_CAP_8_BIT_DATA could be dependent on board.
I agree about MMC_CAP_CMD23.
Additionally, MMC_CAP_CMD23 is applied for dw-mmc host driver without regard to Exynos5.
>
> >
> >> +static struct dw_mci_drv_data exynos5250_drv_data = {
> >> + .ctrl_type = DW_MCI_TYPE_EXYNOS5250,
> >> + .caps = exynos5250_dwmmc_caps,
> >> +};
> >> +
> >> static const struct of_device_id dw_mci_pltfm_match[] = {
> >> { .compatible = "snps,dw-mshc",
> >> .data = (void *)&synopsis_drv_data, },
> >> + { .compatible = "samsung,exynos5250-dw-mshc",
> >> + .data = (void *)&exynos5250_drv_data, },
> >> {},
> >> };
> >> MODULE_DEVICE_TABLE(of, dw_mci_pltfm_match);
> >> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> >> index 3bc276d..bbf1209 100644
> >> --- a/drivers/mmc/host/dw_mmc.c
> >> +++ b/drivers/mmc/host/dw_mmc.c
> >> @@ -236,6 +236,7 @@ static void dw_mci_set_timeout(struct dw_mci *host)
> >> static u32 dw_mci_prepare_command(struct mmc_host *mmc, struct mmc_command *cmd)
> >> {
> >> struct mmc_data *data;
> >> + struct dw_mci_slot *slot = mmc_priv(mmc);
> >> u32 cmdr;
> >> cmd->error = -EINPROGRESS;
> >>
> >> @@ -265,6 +266,17 @@ static u32 dw_mci_prepare_command(struct mmc_host *mmc, struct mmc_command
> *cmd)
> >> cmdr |= SDMMC_CMD_DAT_WR;
> >> }
> >>
> >> + /*
> >> + * Samsung Exynos5250 extends the use of CMD register with the use of
> >> + * bit 29 (which is reserved on standard MSHC controllers) for
> >> + * optionally bypassing the HOLD register for command and data. The
> >> + * HOLD register should be bypassed in case there is no phase shift
> >> + * applied on CMD/DATA that is sent to the card.
> >> + */
> >> + if (slot->host->drv_data->ctrl_type == DW_MCI_TYPE_EXYNOS5250)
> >> + if (SDMMC_CLKSEL_GET_SELCLK_DRV(mci_readl(slot->host, CLKSEL)))
> >> + cmdr |= SDMMC_CMD_USE_HOLD_REG;
> >> +
> >> return cmdr;
> >> }
> >>
> >> @@ -802,10 +814,19 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> >> regs = mci_readl(slot->host, UHS_REG);
> >>
> >> /* DDR mode set */
> >> - if (ios->timing == MMC_TIMING_UHS_DDR50)
> >> + if (ios->timing == MMC_TIMING_UHS_DDR50) {
> >> regs |= (0x1 << slot->id) << 16;
> >> - else
> >> + mci_writel(slot->host, CLKSEL, slot->host->ddr_timing);
> >> + } else {
> >> regs &= ~(0x1 << slot->id) << 16;
> >> + mci_writel(slot->host, CLKSEL, slot->host->sdr_timing);
> >> + }
> >> +
> >> + if (slot->host->drv_data->ctrl_type == DW_MCI_TYPE_EXYNOS5250) {
> >> + slot->host->bus_hz = clk_get_rate(slot->host->ciu_clk);
> >> + slot->host->bus_hz /= SDMMC_CLKSEL_GET_DIVRATIO(
> >> + mci_readl(slot->host, CLKSEL));
> >> + }
> > As you know, CLKSEL is specific for Samsung soc.
> > 0x09C(CLKSEL) is reserved area in Synopsys memory map.
> > In case of non-samsung-soc, we cannot ensure this usage.
> > In previous version, I have suggested separating the variant into another file.
>
> There is a check for type of SoC before using 0x9C as CLKSEL register.
Do you mean checking DW_MCI_TYPE_EXYNOS5250?
But Above two case(ddr_timing/sdr_timing), CLKSEL can be accessed on other soc's.
> Other implementations of dw-mmc might define custom register at 0x9C
Even so, register field can be different with Samsung soc.
> but this will code will not execute on other SoC's and will not break
> anything on other implementations. Regarding spliting this Exynos
> specific code into another file, I prefer not to do it for now.
> Spliting the code means adding new definitions of callback functions
> which I am not sure is really required. The present code is fairly
> simple one.
Yes, callback functions might be needed to accommodate various implementation
of host controller. It would be better to prepare this for other variant next.
>
> >
> >>
> >> mci_writel(slot->host, UHS_REG, regs);
> >>
> >> @@ -2086,6 +2107,7 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
> >> struct dw_mci_board *pdata;
> >> struct device *dev = host->dev;
> >> struct device_node *np = dev->of_node;
> >> + u32 timing[3];
> >> int idx, cnt;
> >>
> >> pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
> >> @@ -2108,6 +2130,20 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
> >> if (of_get_property(np, of_quriks[idx].quirk, NULL))
> >> pdata->quirks |= of_quriks[idx].id;
> >>
> >> + if (of_property_read_u32_array(dev->of_node,
> >> + "samsung,dw-mshc-sdr-timing", timing, 3))
> >> + host->sdr_timing = DW_MCI_DEF_SDR_TIMING;
> > Host of non-samsung will reach here.
> > host->sdr_timing is needed for this host? host->ddr_timing is the same.
>
> Yes, but non-samsung hosts will not have have this property into their
> dts file. So the code within the condition will not execute on
> non-samsung hosts. SDR and DDR timing are required for Exynos5 SoC.
Yes, these are required only for Exynos Soc.
Non-samsung host will have default value here, but it seems to be meaningless.
>
> >
> >> + else
> >> + host->sdr_timing = SDMMC_CLKSEL_TIMING(timing[0],
> >> + timing[1], timing[2]);
> >> +
> >> + if (of_property_read_u32_array(dev->of_node,
> >> + "samsung,dw-mshc-ddr-timing", timing, 3))
> >> + host->ddr_timing = DW_MCI_DEF_DDR_TIMING;
> >> + else
> >> + host->ddr_timing = SDMMC_CLKSEL_TIMING(timing[0],
> >> + timing[1], timing[2]);
> >> +
> >> if (of_property_read_u32(np, "fifo-depth", &pdata->fifo_depth))
> >> dev_info(dev, "fifo-depth property not found, using "
> >> "value of FIFOTH register as default\n");
> >> diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
> >> index 1ecaa02..6c17282 100644
> >> --- a/drivers/mmc/host/dw_mmc.h
> >> +++ b/drivers/mmc/host/dw_mmc.h
> >> @@ -53,6 +53,7 @@
> >> #define SDMMC_IDINTEN 0x090
> >> #define SDMMC_DSCADDR 0x094
> >> #define SDMMC_BUFADDR 0x098
> >> +#define SDMMC_CLKSEL 0x09C /* specific to Samsung Exynos5250 */
> >> #define SDMMC_DATA(x) (x)
> >>
> >> /*
> >> @@ -111,6 +112,7 @@
> >> #define SDMMC_INT_ERROR 0xbfc2
> >> /* Command register defines */
> >> #define SDMMC_CMD_START BIT(31)
> >> +#define SDMMC_CMD_USE_HOLD_REG BIT(29)
> >> #define SDMMC_CMD_CCS_EXP BIT(23)
> >> #define SDMMC_CMD_CEATA_RD BIT(22)
> >> #define SDMMC_CMD_UPD_CLK BIT(21)
> >> @@ -142,6 +144,17 @@
> >> /* Version ID register define */
> >> #define SDMMC_GET_VERID(x) ((x) & 0xFFFF)
> >>
> >> +#define DW_MCI_DEF_SDR_TIMING 0x03030002
> >> +#define DW_MCI_DEF_DDR_TIMING 0x03020001
> > What is the basis for these timing?
> > These values is board-specific.
One missed comment?
> >
> >> +#define SDMMC_CLKSEL_CCLK_SAMPLE(x) (((x) & 3) << 0)
> >> +#define SDMMC_CLKSEL_CCLK_DRIVE(x) (((x) & 3) << 16)
> >> +#define SDMMC_CLKSEL_CCLK_DIVIDER(x) (((x) & 3) << 24)
> > If it's for exynos5, it will be 7 not 3.
>
> Yes, I missed that. Thanks. I will fix this.
>
> >
> >> +#define SDMMC_CLKSEL_TIMING(x, y, z) (SDMMC_CLKSEL_CCLK_SAMPLE(x) | \
> >> + SDMMC_CLKSEL_CCLK_DRIVE(y) | \
> >> + SDMMC_CLKSEL_CCLK_DIVIDER(z))
> >> +#define SDMMC_CLKSEL_GET_DIVRATIO(x) ((((x) >> 24) & 0x7) + 1)
> >> +#define SDMMC_CLKSEL_GET_SELCLK_DRV(x) (((x) >> 16) & 0x7)
> >> +
> > Is this patch considered only for exynos5250?
> > In case of exynos4210, the number of bits is different.
> > If upper macros is backward-compatible, it would be better.
>
> These consider the Exynos4210 and Exynos4412 implementations as well.
> The device tree documentation clearly states that the possible values
> for each of the dividers. For Exynos4 SoC's, the divider value is
> between 1 to 4 (or 0 to 3). So a bit mask of 7 is backward compatilble
> for Exynos4.
Bit width is 2 for selclk_drv in exynos4210.
So bit mask of 3 is proper.
Let me clear it about divider value.
In case of Exynos4 SoC's, divider value(DIVRATIO) is reserved and host doesn't modify.
But value is fixed internally like following.
Exynos4210 : 2
Exynos4412 : 4
Thanks,
Seungwon Jeon
>
> Thanks for your review and comments on this patch.
>
> Regards,
> Thomas.
>
> >
> > Best regards,
> > Seungwon Jeon
> >
> >> /* Register access macros */
> >> #define mci_readl(dev, reg) \
> >> __raw_readl((dev)->regs + SDMMC_##reg)
> >> @@ -184,6 +197,7 @@ extern int dw_mci_resume(struct dw_mci *host);
> >>
> >> /* Variations in the dw_mci controller */
> >> #define DW_MCI_TYPE_SYNOPSIS 0
> >> +#define DW_MCI_TYPE_EXYNOS5250 1 /* Samsung Exynos5250 Extensions */
> >>
> >> /* dw_mci platform driver data */
> >> struct dw_mci_drv_data {
> >> diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
> >> index ae45e4f..32c778f 100644
> >> --- a/include/linux/mmc/dw_mmc.h
> >> +++ b/include/linux/mmc/dw_mmc.h
> >> @@ -82,6 +82,8 @@ struct mmc_data;
> >> * @biu_clk: Pointer to bus interface unit clock instance.
> >> * @ciu_clk: Pointer to card interface unit clock instance.
> >> * @slot: Slots sharing this MMC controller.
> >> + * @sdr_timing: Clock phase shifting for driving and sampling in sdr mode
> >> + * @ddr_timing: Clock phase shifting for driving and sampling in ddr mode
> >> * @fifo_depth: depth of FIFO.
> >> * @data_shift: log2 of FIFO item size.
> >> * @part_buf_start: Start index in part_buf.
> >> @@ -166,6 +168,10 @@ struct dw_mci {
> >> struct clk *ciu_clk;
> >> struct dw_mci_slot *slot[MAX_MCI_SLOTS];
> >>
> >> + /* Phase Shift Value (for exynos5250 variant) */
> >> + u32 sdr_timing;
> >> + u32 ddr_timing;
> >> +
> >> /* FIFO push and pull */
> >> int fifo_depth;
> >> int data_shift;
> >> --
> >> 1.6.6.rc2
> >>
> >> --
> >> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> >> the body of a message to majordomo at vger.kernel.org
> >> More majordomo info at http://vger.kernel.org/majordomo-info.html
> >
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
More information about the linux-arm-kernel
mailing list