[PATCH v5 6/7] ARM: mtd: nand: davinci: add OF support for davinci nand controller
Sekhar Nori
nsekhar at ti.com
Wed Jul 18 13:45:28 EDT 2012
Hi Heiko,
On 5/30/2012 3:49 PM, Heiko Schocher wrote:
> add OF support for the davinci nand controller.
>
> Signed-off-by: Heiko Schocher <hs at denx.de>
> Cc: davinci-linux-open-source at linux.davincidsp.com
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: devicetree-discuss at lists.ozlabs.org
> Cc: linux-mtd at lists.infradead.org
> Cc: David Woodhouse <dwmw2 at infradead.org>
> Cc: Grant Likely <grant.likely at secretlab.ca>
> Cc: Sekhar Nori <nsekhar at ti.com>
> Cc: Wolfgang Denk <wd at denx.de>
> Cc: Scott Wood <scottwood at freescale.com>
>
> ---
> - changes for v2:
> - add comments from Scott Wood:
> - add "ti,davinci-" prefix
> - Dashes are preferred to underscores
> - rename "nandflash" to "nand"
> - introduce new "ti,davinci" specific properties for setting
> up ecc_mode, ecc_bits, options and bbt options, instead
> using linux defines
> - readme fixes
> - no changes for v3
> - changes for v4
> remove "pinmux-handle" property as discussed here:
> http://www.spinics.net/lists/arm-kernel/msg175701.html
> with Nori Sekhar
> - no changes for v5
>
> .../devicetree/bindings/arm/davinci/nand.txt | 72 ++++++++++++++++++
> drivers/mtd/nand/davinci_nand.c | 80 +++++++++++++++++++-
> 2 files changed, 151 insertions(+), 1 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/arm/davinci/nand.txt
>
> diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt
> new file mode 100644
> index 0000000..5afe4a6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt
> @@ -0,0 +1,72 @@
> +* Texas Instruments Davinci NAND
> +
> +This file provides information, what the device node for the
> +davinci nand interface contain.
> +
> +Required properties:
> +- compatible: "ti,davinci-nand";
> +- reg : contain 2 offset/length values:
> + - offset and length for the access window
> + - offset and length for accessing the aemif control registers
> +- ti,davinci-chipselect: Indicates on the davinci_nand driver which
> + chipselect is used for accessing the nand.
> +
> +Recommended properties :
> +- ti,davinci-mask-ale: mask for ale
> +- ti,davinci-mask-cle: mask for cle
> +- ti,davinci-mask-chipsel: mask for chipselect
> +- ti,davinci-ecc-mode: ECC mode valid values for davinci driver:
> + - "none"
> + - "soft"
> + - "hw"
> +- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
> +- ti,davinci-nand-buswidth: buswidth 8 or 16
> +- ti,davinci-nand-use-bbt: use flash based bad block table support.
> +
> +Optional properties:
> +- timing-handle: contains a handle to setup aemif timing.
> +
> +Example (enbw_cmc board):
> +aemif at 60000000 {
> + compatible = "ti,davinci-aemif";
> + #address-cells = <2>;
> + #size-cells = <1>;
> + reg = <0x68000000 0x80000>;
> + ranges = <2 0 0x60000000 0x02000000
> + 3 0 0x62000000 0x02000000
> + 4 0 0x64000000 0x02000000
> + 5 0 0x66000000 0x02000000
> + 6 0 0x68000000 0x02000000>;
> + nand_cs: cs3 at 68000000 {
> + compatible = "ti,davinci-cs";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + /* all timings in nanoseconds */
> + cs = <3>;
> + asize = <0>;
> + ta = <0>;
> + rhold = <7>;
> + rstrobe = <42>;
> + rsetup = <7>;
> + whold = <7>;
> + wstrobe = <14>;
> + wsetup = <7>;
> + ew = <0>;
> + ss = <0>;
> + };
> + nand at 3,0 {
> + compatible = "ti,davinci-nand";
> + reg = <3 0x0 0x807ff
> + 6 0x0 0x8000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ti,davinci-chipselect = <1>;
> + ti,davinci-mask-ale = <0>;
> + ti,davinci-mask-cle = <0>;
> + ti,davinci-mask-chipsel = <0>;
> + ti,davinci-ecc-mode = "hw";
> + ti,davinci-ecc-bits = <4>;
> + ti,davinci-nand-use-bbt;
> + timing-handle = <&nand_cs>;
> + };
> +};
> diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
> index d94b03c..67bdd29 100644
> --- a/drivers/mtd/nand/davinci_nand.c
> +++ b/drivers/mtd/nand/davinci_nand.c
> @@ -33,9 +33,12 @@
> #include <linux/mtd/nand.h>
> #include <linux/mtd/partitions.h>
> #include <linux/slab.h>
> +#include <linux/of_i2c.h>
This include is not required.
> +#include <linux/of_device.h>
>
> #include <mach/nand.h>
> #include <mach/aemif.h>
> +#include <mach/mux.h>
This too.
>
> /*
> * This is a device driver for the NAND flash controller found on the
> @@ -518,9 +521,81 @@ static struct nand_ecclayout hwecc4_2048 __initconst = {
> },
> };
>
> +#if defined(CONFIG_OF)
> +static const struct of_device_id davinci_nand_of_match[] = {
> + {.compatible = "ti,davinci-nand", },
> + {},
> +}
> +MODULE_DEVICE_TABLE(of, davinci_nand_of_match);
> +
> +static struct davinci_nand_pdata
> + *nand_davinci_get_pdata(struct platform_device *pdev)
> +{
> + if ((pdev->dev.platform_data == NULL) &&
> + (pdev->dev.of_node)) {
You can simplify this and also avoid breaking the statement.
if (!pdev->dev.platform_data && pdev->dev.of_node) {
> + struct device_node *tmp_np;
> + struct davinci_nand_pdata *pdata;
> + const char *mode;
> + u32 prop;
> + int len;
> +
> + pdata = kzalloc(sizeof(struct davinci_nand_pdata),
> + GFP_KERNEL);
I don't see this getting freed anywhere. You wanted to use devm_kzalloc()?
> + pdev->dev.platform_data = pdata;
> + if (!pdata)
> + return NULL;
> + if (!of_property_read_u32(pdev->dev.of_node,
> + "ti,davinci-chipselect", &prop))
> + pdev->id = prop;
> + if (!of_property_read_u32(pdev->dev.of_node,
> + "ti,davinci-mask-ale", &prop))
> + pdata->mask_ale = prop;
> + if (!of_property_read_u32(pdev->dev.of_node,
> + "ti,davinci-mask-cle", &prop))
> + pdata->mask_cle = prop;
> + if (!of_property_read_u32(pdev->dev.of_node,
> + "ti,davinci-mask-chipsel", &prop))
> + pdata->mask_chipsel = prop;
> + if (!of_property_read_string(pdev->dev.of_node,
> + "ti,davinci-ecc-mode", &mode)) {
> + if (!strncmp("none", mode, 4))
> + pdata->ecc_mode = NAND_ECC_NONE;
> + if (!strncmp("soft", mode, 4))
> + pdata->ecc_mode = NAND_ECC_SOFT;
> + if (!strncmp("hw", mode, 2))
> + pdata->ecc_mode = NAND_ECC_HW;
> + }
> + if (!of_property_read_u32(pdev->dev.of_node,
> + "ti,davinci-ecc-bits", &prop))
> + pdata->ecc_bits = prop;
> + if (!of_property_read_u32(pdev->dev.of_node,
> + "ti,davinci-nand-buswidth", &prop))
> + if (prop == 16)
> + pdata->options |= NAND_BUSWIDTH_16;
> + if (of_find_property(pdev->dev.of_node,
> + "ti,davinci-nand-use-bbt", &len))
> + pdata->bbt_options = NAND_BBT_USE_FLASH;
> +
> + tmp_np = of_parse_phandle(pdev->dev.of_node,
> + "timing-handle", 0);
> + if (tmp_np)
> + davinci_aemif_setup_timing_of(tmp_np);
Since the aemif driver conversion to DT needs to be looked at along with
its movement to drivers/ folder, is it possible to drop the AEMIF timing
specific bindings from the patch and only keep the NAND specific ones?
Thanks,
Sekhar
More information about the linux-arm-kernel
mailing list