[PATCH 12/12] USB: chipidea: add imx usbmisc support
Marc Kleine-Budde
mkl at pengutronix.de
Fri Jul 13 10:14:27 EDT 2012
On 07/13/2012 04:02 PM, Richard Zhao wrote:
> On Fri, Jul 13, 2012 at 02:25:45PM +0200, Michael Grzeschik wrote:
>> On Thu, Jul 12, 2012 at 03:01:52PM +0800, Richard Zhao wrote:
>>> i.MX usb controllers shares non-core registers, which may include
>>> SoC specific controls. We take it as a usbmisc device and usbmisc
>>> driver export functions needed by ci13xxx_imx driver.
>>
>> So this is SoC and not chipidea specific and should not be sorted into
>> this subdir.
> Yes, but it's usb specific and serve chipidea usb IP.
I don't care where this code is located.
>>> For example, Sabrelite board has bad over-current design, we can
>>> usbmisc to disable over-current detect.
>>
>> This driver layout is also reflected in:
>>
>> arch/arm/mach-imx/ehci-imx*.c
> It sounds sensible, but I'm not quite sure. I saw drivers are moving
> out of there, event it's SoC specific, for example, clk, pinmux. And
> the non-core registers might not only be setup onetime on boot, but
> be called at runtime by usb driver. For now, it's set once.
>>
>> You should use these existing mx*_initialize_usb_hw functions to avoid
>> code duplication
> I can not see what duplication it can avoid.
We want to use the chipidea driver for the other imx, too. We already
have existing code for the non-DT case in arch/arm/mach-imx/ehci-imx*.c.
So we need to glue these functions to the DT or duplicate the code,
which is to be avoided.
>> and add your mx6_initialize_usb_hw routine for mx6 there.
> Maybe.
Or at least next to the other imx usb-misc code (wherever that will end up).
>> This devicetree based glue code in this file can be reused to
>> call the right mx*_initialize_usb_hw by the compatible.
> The glue code makes it more like a normal driver. Doesn't it?
>>
>> We already have common flags available like i.e. MXC_EHCI_POWER_PINS_ENABLED
>> which is currently used to disable overcurrent detection.
> The flags may be replace with properties in DT bindings.
Yes, write some code that extracts these flags from the DT and then
calls the existing code (for the existing imx platforms).
>>> Signed-off-by: Richard Zhao <richard.zhao at freescale.com>
>>> ---
>>> .../devicetree/bindings/usb/imx-usbmisc.txt | 15 ++
>>> drivers/usb/chipidea/Makefile | 2 +-
>>> drivers/usb/chipidea/ci13xxx_imx.c | 4 +
>>> drivers/usb/chipidea/imx_usbmisc.c | 144 ++++++++++++++++++++
>>> 4 files changed, 164 insertions(+), 1 deletion(-)
>>> create mode 100644 Documentation/devicetree/bindings/usb/imx-usbmisc.txt
>>> create mode 100644 drivers/usb/chipidea/imx_usbmisc.c
>>>
>>> diff --git a/Documentation/devicetree/bindings/usb/imx-usbmisc.txt b/Documentation/devicetree/bindings/usb/imx-usbmisc.txt
>>> new file mode 100644
>>> index 0000000..09f01ca
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/usb/imx-usbmisc.txt
>>> @@ -0,0 +1,15 @@
>>> +* Freescale i.MX non-core registers
>>> +
>>> +Required properties:
>>> +- compatible: Should be "fsl,imx6q-usbmisc"
>>> +- reg: Should contain registers location and length
>>> +
>>> +Optional properties:
>>> +- fsl,disable-over-current: disable over current detect
>>> +
>>> +Examples:
>>> +usbmisc at 02184800 {
>>> + compatible = "fsl,imx6q-usbmisc";
>>> + reg = <0x02184800 0x200>;
>>> + fsl,disable-over-current;
>>> +};
>>> diff --git a/drivers/usb/chipidea/Makefile b/drivers/usb/chipidea/Makefile
>>> index 3f56b76..46fc31c 100644
>>> --- a/drivers/usb/chipidea/Makefile
>>> +++ b/drivers/usb/chipidea/Makefile
>>> @@ -17,5 +17,5 @@ ifneq ($(CONFIG_PCI),)
>>> endif
>>>
>>> ifneq ($(CONFIG_OF_DEVICE),)
>>> - obj-$(CONFIG_USB_CHIPIDEA) += ci13xxx_imx.o
>>> + obj-$(CONFIG_USB_CHIPIDEA) += ci13xxx_imx.o imx_usbmisc.o
>>> endif
>>> diff --git a/drivers/usb/chipidea/ci13xxx_imx.c b/drivers/usb/chipidea/ci13xxx_imx.c
>>> index b3173d8..dd7f3a3 100644
>>> --- a/drivers/usb/chipidea/ci13xxx_imx.c
>>> +++ b/drivers/usb/chipidea/ci13xxx_imx.c
>>> @@ -24,6 +24,8 @@
>>>
>>> #include "ci.h"
>>>
>>> +int imx_usbmisc_init(struct device *usbdev);
>>> +
>>> #define pdev_to_phy(pdev) \
>>> ((struct usb_phy *)platform_get_drvdata(pdev))
>>> #define ci_to_imx_data(ci) \
>>> @@ -142,6 +144,8 @@ static int __devinit ci13xxx_imx_probe(struct platform_device *pdev)
>>> dma_set_coherent_mask(&pdev->dev, *pdev->dev.dma_mask);
>>> }
>>>
>>> + imx_usbmisc_init(&pdev->dev);
>>> +
>>> platform_set_drvdata(pdev, data);
>>>
>>> plat_ci = ci13xxx_add_device(&pdev->dev,
>>> diff --git a/drivers/usb/chipidea/imx_usbmisc.c b/drivers/usb/chipidea/imx_usbmisc.c
>>> new file mode 100644
>>> index 0000000..33a8ec0
>>> --- /dev/null
>>> +++ b/drivers/usb/chipidea/imx_usbmisc.c
>>> @@ -0,0 +1,144 @@
>>> +/*
>>> + * Copyright 2012 Freescale Semiconductor, Inc.
>>> + *
>>> + * The code contained herein is licensed under the GNU General Public
>>> + * License. You may obtain a copy of the GNU General Public License
>>> + * Version 2 or later at the following locations:
>>> + *
>>> + * http://www.opensource.org/licenses/gpl-license.html
>>> + * http://www.gnu.org/copyleft/gpl.html
>>> + */
>>> +
>>> +#include <linux/module.h>
>>> +#include <linux/of_platform.h>
>>> +#include <linux/clk.h>
>>> +#include <linux/err.h>
>>> +#include <asm/io.h>
>>> +
>>> +struct usbmisc;
>>> +
>>> +struct soc_data {
>>> + int (*init) (struct usbmisc *usbmisc, int id);
>>> + void (*exit) (struct usbmisc *usbmisc, int id);
>>> +};
>>> +
>>> +struct usbmisc {
>>> + struct soc_data *soc_data;
>>> + void __iomem *base;
>>> + struct clk *clk;
>>> +
>>> + int dis_oc:1;
>>> +};
>>> +
>>> +/* Since we only have one usbmisc device at runtime, we global variables */
>>> +static struct usbmisc *usbmisc;
>>
>> Global variable?
> Yes. we only have one usbmisc.
>>
>>> +
>>> +static int imx6q_usbmisc_init(struct usbmisc *usbmisc, int id)
>>
>> What is initialized here? How about "preconfigure"?
>> Even better is to reuse mx*_initialize_usb_hw here.
> It's used to call by ci13xxx_imx driver.
>>
>>> +{
>>> + u32 reg;
>>> +
>>> + if (usbmisc->dis_oc) {
>>> + reg = readl_relaxed(usbmisc->base + id * 4);
>>> + writel_relaxed(reg | (1 << 7), usbmisc->base + id * 4);
>>
>> #define IMX6_OTG_CTRL_USBMISC 1 << 7
> yes.
>>
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static struct soc_data imx6q_data = {
>>> + .init = imx6q_usbmisc_init,
>>> +};
>>> +
>>> +
>>> +static const struct of_device_id imx_usbmisc_dt_ids[] = {
>>> + { .compatible = "fsl,imx6q-usbmisc", .data = &imx6q_data },
>>
>> something like this:
>> { .compatible = "fsl,imx6q-usbmisc", .data = &mx6_initialize_usb_hw },
> It's designed not only used when initialization.
>>
>>> + { /* sentinel */ }
>>> +};
>>> +
>>> +static int __devinit imx_usbmisc_probe(struct platform_device *pdev)
>>> +{
>>> + struct resource *res;
>>> + struct usbmisc *data;
>>> + const struct of_device_id *of_id =
>>> + of_match_device(imx_usbmisc_dt_ids, &pdev->dev);
>>> +
>>> + int ret;
>>> +
>>> + if (usbmisc)
>>> + return -EBUSY;
>>> +
>>> + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
>>> + if (!data)
>>> + return -ENOMEM;
>>> +
>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>> + data->base = devm_request_and_ioremap(&pdev->dev, res);
>>> + if (!data->base)
>>> + return -EADDRNOTAVAIL;
>>> +
>>> + data->clk = devm_clk_get(&pdev->dev, NULL);
>>> + if (IS_ERR(data->clk)) {
>>> + dev_err(&pdev->dev,
>>> + "failed to get clock, err=%ld\n", PTR_ERR(data->clk));
>>> + return PTR_ERR(data->clk);
>>> + }
>>> +
>>> + ret = clk_prepare_enable(data->clk);
>>> + if (!ret) {
>>
>> Better:
>> if (ret)
>> return ret;
> To me, it does not make much difference.
Not the the compiler, but IMHO the common pattern in the kernel is:
ret = sensible_init();
if (ret)
return ret;
do_work();
>>
>>> + if (of_find_property(pdev->dev.of_node,
>>> + "fsl,disable-over-current", NULL))
>>> + data->dis_oc = 1;
>>> + data->soc_data = of_id->data;
>>> + usbmisc = data;
>>> + }
>>> +
>> if (of_find_property(pdev->dev.of_node,
>> ...
>>
>>> + return ret;
>>> +}
>>> +
>>> +static int __devexit imx_usbmisc_remove(struct platform_device *pdev)
>>> +{
>>> + clk_disable_unprepare(usbmisc->clk);
>>> + return 0;
>>> +}
>>> +
>>> +static struct platform_driver imx_usbmisc_driver = {
>>> + .probe = imx_usbmisc_probe,
>>> + .remove = __devexit_p(imx_usbmisc_remove),
>>> + .driver = {
>>> + .name = "imx_usbmisc",
>>> + .owner = THIS_MODULE,
>>> + .of_match_table = imx_usbmisc_dt_ids,
>>> + },
>>> +};
>>> +
>>> +int imx_usbmisc_init(struct device *usbdev)
>>> +{
>>> + struct device_node *np = usbdev->of_node;
>>> + int ret;
>>> +
>>> + if (!usbmisc)
>>> + return 0;
>>> +
>>> + ret = of_alias_get_id(np, "usb");
>>> + if (ret < 0) {
>>> + dev_err(usbdev, "failed to get alias id, errno %d\n", ret);
>>> + return ret;
>>> + }
>>> +
>>> + return usbmisc->soc_data->init(usbmisc, ret);
>>> +}
>>> +EXPORT_SYMBOL_GPL(imx_usbmisc_init);
>>
>> EXPORT_SYMBOL is only needed because it is
>> compliled as an extra kernel module.
> ci13xxx_imx may be module.
Why make the usb_misc an independent module, why not just link it into
the ci13xxx_imx.ko
Marc
--
Pengutronix e.K. | Marc Kleine-Budde |
Industrial Linux Solutions | Phone: +49-231-2826-924 |
Vertretung West/Dortmund | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 262 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20120713/63bb5eb7/attachment.sig>
More information about the linux-arm-kernel
mailing list