[PATCH v2 04/14] ARM: OMAP5: Add minimal support for OMAP5430 SOC
Shilimkar, Santosh
santosh.shilimkar at ti.com
Mon Jul 9 10:26:58 EDT 2012
On Mon, Jul 9, 2012 at 6:56 PM, Shilimkar, Santosh
<santosh.shilimkar at ti.com> wrote:
> On Mon, Jul 9, 2012 at 6:55 PM, Tony Lindgren <tony at atomide.com> wrote:
>> * Tony Lindgren <tony at atomide.com> [120709 06:17]:
>>> * Vaibhav Hiremath <hvaibhav at ti.com> [120709 01:55]:
>>> > On 7/6/2012 2:51 PM, Santosh Shilimkar wrote:
>>> > > --- a/arch/arm/plat-omap/include/plat/clkdev_omap.h
>>> > > +++ b/arch/arm/plat-omap/include/plat/clkdev_omap.h
>>> > > @@ -39,6 +39,7 @@ struct omap_clk {
>>> > > #define CK_443X (1 << 11)
>>> > > #define CK_TI816X (1 << 12)
>>> > > #define CK_446X (1 << 13)
>>> > > +#define CK_54XX (1 << 14)
>>> >
>>> > This is conflicting with AM33XX, you may want to rebase it again, since
>>> > AM33xx clock tree is already pushed and available in
>>> > linux-omap/devel-am33xx-part2.
>>>
>>> Heh these CK_XXXX defines are now running out of the u16 cpu_mask.
>>>
>>> They really should be replaced with SoC specific lists of clocks
>>> rather than bloating the cpu_mask and repeating it for every clock
>>> that's compiled in for 800+ times.
>>>
>>> Below (untested) is what could be done in the short term.
>>>
>>> I wonder if we could #define CK_OMAP_DUMMY 0 that's always set
>>> for non-shared clocks if they only get set in some *_data.c
>>> file in a unique way?
>>>
>>> Paul got any better ideas?
>>
>> Santosh, I suggest you just drop the CK_54XX change from your patches
>> as the clock fwk support will need further patching and is not used
>> yet.
>>
> Good idea. Will have a look at it.
>
I dropped the CK_54XX and RATE hunks from the patch. Updated
patch below for the record.
Regards
Santosh
-->>
>From 05e152c76a1efaa3165afecf5acf535c8283f386 Mon Sep 17 00:00:00 2001
From: R Sricharan <r.sricharan at ti.com>
Date: Tue, 5 Jun 2012 16:21:32 +0530
Subject: [PATCH 04/14] ARM: OMAP5: Add minimal support for OMAP5430 SOC
OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP
architecture. It's a dual core SOC with GIC used for interrupt
handling and with an integrated L2 cache controller.
OMAP5432 is another variant of OMAP5430, with a
memory controller supporting DDR3 and SATA.
Patch includes:
- The machine specific headers and sources updates.
- Platform header updates.
- Minimum initialisation support for serial.
- IO table init
Signed-off-by: R Sricharan <r.sricharan at ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar at ti.com>
---
arch/arm/mach-omap2/Makefile | 23 ++++++++++---
arch/arm/mach-omap2/common.c | 24 +++++++++++++
arch/arm/mach-omap2/common.h | 11 ++++++
arch/arm/mach-omap2/include/mach/debug-macro.S | 8 ++---
arch/arm/mach-omap2/io.c | 44 ++++++++++++++++++++++++
arch/arm/mach-omap2/iomap.h | 27 +++++++++++++++
arch/arm/mach-omap2/omap_hwmod.c | 2 +-
arch/arm/mach-omap2/prcm-common.h | 2 +-
arch/arm/mach-omap2/prcm.c | 2 +-
arch/arm/plat-omap/include/plat/hardware.h | 1 +
arch/arm/plat-omap/include/plat/multi.h | 9 +++++
arch/arm/plat-omap/include/plat/omap54xx.h | 32 +++++++++++++++++
arch/arm/plat-omap/include/plat/serial.h | 10 ++++++
arch/arm/plat-omap/include/plat/uncompress.h | 6 ++++
arch/arm/plat-omap/sram.c | 11 ++++--
15 files changed, 198 insertions(+), 14 deletions(-)
create mode 100644 arch/arm/plat-omap/include/plat/omap54xx.h
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 240f196..085e171 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(hwmod-common)
obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(hwmod-common) $(secure-common)
obj-$(CONFIG_ARCH_OMAP4) += prm44xx.o $(hwmod-common) $(secure-common)
obj-$(CONFIG_SOC_AM33XX) += irq.o $(hwmod-common)
+obj-$(CONFIG_SOC_OMAP5) += prm44xx.o $(hwmod-common) $(secure-common)
ifneq ($(CONFIG_SND_OMAP_SOC_MCBSP),)
obj-y += mcbsp.o
@@ -29,8 +30,10 @@ obj-$(CONFIG_SOC_HAS_OMAP2_SDRC) += sdrc.o
obj-$(CONFIG_SMP) += omap-smp.o omap-headsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += omap-hotplug.o
-obj-$(CONFIG_ARCH_OMAP4) += omap4-common.o omap-wakeupgen.o
-obj-$(CONFIG_ARCH_OMAP4) += sleep44xx.o
+omap-4-5-common = omap4-common.o omap-wakeupgen.o \
+ sleep44xx.o
+obj-$(CONFIG_ARCH_OMAP4) += $(omap-4-5-common)
+obj-$(CONFIG_SOC_OMAP5) += $(omap-4-5-common)
plus_sec := $(call as-instr,.arch_extension sec,+sec)
AFLAGS_omap-headsmp.o :=-Wa,-march=armv7-a$(plus_sec)
@@ -70,6 +73,7 @@ obj-$(CONFIG_ARCH_OMAP2) += sleep24xx.o
obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o
obj-$(CONFIG_ARCH_OMAP3) += cpuidle34xx.o
obj-$(CONFIG_ARCH_OMAP4) += pm44xx.o omap-mpuss-lowpower.o
+obj-$(CONFIG_SOC_OMAP5) += omap-mpuss-lowpower.o
obj-$(CONFIG_ARCH_OMAP4) += cpuidle44xx.o
obj-$(CONFIG_PM_DEBUG) += pm-debug.o
obj-$(CONFIG_OMAP_SMARTREFLEX) += sr_device.o smartreflex.o
@@ -85,14 +89,16 @@ endif
endif
# PRCM
+omap-prcm-4-5-common = prcm.o cminst44xx.o cm44xx.o \
+ prcm_mpu44xx.o prminst44xx.o \
+ vc44xx_data.o vp44xx_data.o
obj-y += prm_common.o
obj-$(CONFIG_ARCH_OMAP2) += prcm.o cm2xxx_3xxx.o prm2xxx_3xxx.o
obj-$(CONFIG_ARCH_OMAP3) += prcm.o cm2xxx_3xxx.o prm2xxx_3xxx.o
obj-$(CONFIG_ARCH_OMAP3) += vc3xxx_data.o vp3xxx_data.o
-obj-$(CONFIG_ARCH_OMAP4) += prcm.o cminst44xx.o cm44xx.o
-obj-$(CONFIG_ARCH_OMAP4) += prcm_mpu44xx.o prminst44xx.o
-obj-$(CONFIG_ARCH_OMAP4) += vc44xx_data.o vp44xx_data.o prm44xx.o
obj-$(CONFIG_SOC_AM33XX) += prcm.o prm33xx.o cm33xx.o
+obj-$(CONFIG_ARCH_OMAP4) += $(omap-prcm-4-5-common) prm44xx.o
+obj-$(CONFIG_SOC_OMAP5) += $(omap-prcm-4-5-common)
# OMAP voltage domains
voltagedomain-common := voltage.o vc.o vp.o
@@ -104,6 +110,7 @@ obj-$(CONFIG_ARCH_OMAP4) += $(voltagedomain-common)
obj-$(CONFIG_ARCH_OMAP4) += voltagedomains44xx_data.o
obj-$(CONFIG_SOC_AM33XX) += $(voltagedomain-common)
obj-$(CONFIG_SOC_AM33XX) += voltagedomains33xx_data.o
+obj-$(CONFIG_SOC_OMAP5) += $(voltagedomain-common)
# OMAP powerdomain framework
powerdomain-common += powerdomain.o powerdomain-common.o
@@ -121,6 +128,8 @@ obj-$(CONFIG_ARCH_OMAP4) += powerdomains44xx_data.o
obj-$(CONFIG_SOC_AM33XX) += $(powerdomain-common)
obj-$(CONFIG_SOC_AM33XX) += powerdomain33xx.o
obj-$(CONFIG_SOC_AM33XX) += powerdomains33xx_data.o
+obj-$(CONFIG_SOC_OMAP5) += $(powerdomain-common)
+obj-$(CONFIG_SOC_OMAP5) += powerdomain44xx.o
# PRCM clockdomain control
clockdomain-common += clockdomain.o
@@ -139,6 +148,8 @@ obj-$(CONFIG_ARCH_OMAP4) += clockdomains44xx_data.o
obj-$(CONFIG_SOC_AM33XX) += $(clockdomain-common)
obj-$(CONFIG_SOC_AM33XX) += clockdomain33xx.o
obj-$(CONFIG_SOC_AM33XX) += clockdomains33xx_data.o
+obj-$(CONFIG_SOC_OMAP5) += $(clockdomain-common)
+obj-$(CONFIG_SOC_OMAP5) += clockdomain44xx.o
# Clock framework
obj-$(CONFIG_ARCH_OMAP2) += $(clock-common) clock2xxx.o
@@ -157,6 +168,8 @@ obj-$(CONFIG_ARCH_OMAP3) += clkt_iclk.o
obj-$(CONFIG_ARCH_OMAP4) += $(clock-common) clock44xx_data.o
obj-$(CONFIG_ARCH_OMAP4) += dpll3xxx.o dpll44xx.o
obj-$(CONFIG_SOC_AM33XX) += $(clock-common) dpll3xxx.o
+obj-$(CONFIG_SOC_OMAP5) += $(clock-common)
+obj-$(CONFIG_SOC_OMAP5) += dpll3xxx.o dpll44xx.o
# OMAP2 clock rate set data (old "OPP" data)
obj-$(CONFIG_SOC_OMAP2420) += opp2420_data.o
diff --git a/arch/arm/mach-omap2/common.c b/arch/arm/mach-omap2/common.c
index 73d2a0b..069f972 100644
--- a/arch/arm/mach-omap2/common.c
+++ b/arch/arm/mach-omap2/common.c
@@ -178,3 +178,27 @@ void __init omap4_map_io(void)
}
#endif
+#if defined(CONFIG_SOC_OMAP5)
+static struct omap_globals omap5_globals = {
+ .class = OMAP54XX_CLASS,
+ .tap = OMAP2_L4_IO_ADDRESS(OMAP54XX_SCM_BASE),
+ .ctrl = OMAP2_L4_IO_ADDRESS(OMAP54XX_SCM_BASE),
+ .ctrl_pad = OMAP2_L4_IO_ADDRESS(OMAP54XX_CTRL_BASE),
+ .prm = OMAP2_L4_IO_ADDRESS(OMAP54XX_PRM_BASE),
+ .cm = OMAP2_L4_IO_ADDRESS(OMAP54XX_CM_CORE_AON_BASE),
+ .cm2 = OMAP2_L4_IO_ADDRESS(OMAP54XX_CM_CORE_BASE),
+ .prcm_mpu = OMAP2_L4_IO_ADDRESS(OMAP54XX_PRCM_MPU_BASE),
+};
+
+void __init omap2_set_globals_5xxx(void)
+{
+ omap2_set_globals_tap(&omap5_globals);
+ omap2_set_globals_control(&omap5_globals);
+ omap2_set_globals_prcm(&omap5_globals);
+}
+
+void __init omap5_map_io(void)
+{
+ omap5_map_common_io();
+}
+#endif
diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h
index 404f172..399e5bb 100644
--- a/arch/arm/mach-omap2/common.h
+++ b/arch/arm/mach-omap2/common.h
@@ -115,6 +115,14 @@ static inline int omap_mux_late_init(void)
}
#endif
+#ifdef CONFIG_SOC_OMAP5
+extern void omap5_map_common_io(void);
+#else
+static inline void omap5_map_common_io(void)
+{
+}
+#endif
+
extern void omap2_init_common_infrastructure(void);
extern struct sys_timer omap2_timer;
@@ -134,6 +142,7 @@ void am35xx_init_early(void);
void ti81xx_init_early(void);
void am33xx_init_early(void);
void omap4430_init_early(void);
+void omap5_init_early(void);
void omap3_init_late(void); /* Do not use this one */
void omap4430_init_late(void);
void omap2420_init_late(void);
@@ -169,6 +178,7 @@ void omap2_set_globals_242x(void);
void omap2_set_globals_243x(void);
void omap2_set_globals_3xxx(void);
void omap2_set_globals_443x(void);
+void omap2_set_globals_5xxx(void);
void omap2_set_globals_ti81xx(void);
void omap2_set_globals_am33xx(void);
@@ -188,6 +198,7 @@ void omap243x_map_io(void);
void omap3_map_io(void);
void am33xx_map_io(void);
void omap4_map_io(void);
+void omap5_map_io(void);
void ti81xx_map_io(void);
void omap_barriers_init(void);
diff --git a/arch/arm/mach-omap2/include/mach/debug-macro.S
b/arch/arm/mach-omap2/include/mach/debug-macro.S
index d7f844a..93d10de 100644
--- a/arch/arm/mach-omap2/include/mach/debug-macro.S
+++ b/arch/arm/mach-omap2/include/mach/debug-macro.S
@@ -60,12 +60,12 @@ omap_uart_lsr: .word 0
beq 23f @ configure OMAP2UART3
cmp \rp, #OMAP3UART3 @ only on 34xx
beq 33f @ configure OMAP3UART3
- cmp \rp, #OMAP4UART3 @ only on 44xx
- beq 43f @ configure OMAP4UART3
+ cmp \rp, #OMAP4UART3 @ only on 44xx/54xx
+ beq 43f @ configure OMAP4/5UART3
cmp \rp, #OMAP3UART4 @ only on 36xx
beq 34f @ configure OMAP3UART4
- cmp \rp, #OMAP4UART4 @ only on 44xx
- beq 44f @ configure OMAP4UART4
+ cmp \rp, #OMAP4UART4 @ only on 44xx/54xx
+ beq 44f @ configure OMAP4/5UART4
cmp \rp, #TI81XXUART1 @ ti81Xx UART offsets different
beq 81f @ configure UART1
cmp \rp, #TI81XXUART2 @ ti81Xx UART offsets different
diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index cb6c11c..8976be9 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -233,6 +233,35 @@ static struct map_desc omap44xx_io_desc[] __initdata = {
};
#endif
+#ifdef CONFIG_SOC_OMAP5
+static struct map_desc omap54xx_io_desc[] __initdata = {
+ {
+ .virtual = L3_54XX_VIRT,
+ .pfn = __phys_to_pfn(L3_54XX_PHYS),
+ .length = L3_54XX_SIZE,
+ .type = MT_DEVICE,
+ },
+ {
+ .virtual = L4_54XX_VIRT,
+ .pfn = __phys_to_pfn(L4_54XX_PHYS),
+ .length = L4_54XX_SIZE,
+ .type = MT_DEVICE,
+ },
+ {
+ .virtual = L4_WK_54XX_VIRT,
+ .pfn = __phys_to_pfn(L4_WK_54XX_PHYS),
+ .length = L4_WK_54XX_SIZE,
+ .type = MT_DEVICE,
+ },
+ {
+ .virtual = L4_PER_54XX_VIRT,
+ .pfn = __phys_to_pfn(L4_PER_54XX_PHYS),
+ .length = L4_PER_54XX_SIZE,
+ .type = MT_DEVICE,
+ },
+};
+#endif
+
#ifdef CONFIG_SOC_OMAP2420
void __init omap242x_map_common_io(void)
{
@@ -278,6 +307,12 @@ void __init omap44xx_map_common_io(void)
}
#endif
+#ifdef CONFIG_SOC_OMAP5
+void __init omap5_map_common_io(void)
+{
+ iotable_init(omap54xx_io_desc, ARRAY_SIZE(omap54xx_io_desc));
+}
+#endif
/*
* omap2_init_reprogram_sdrc - reprogram SDRC timing parameters
*
@@ -513,6 +548,15 @@ void __init omap4430_init_late(void)
}
#endif
+#ifdef CONFIG_SOC_OMAP5
+void __init omap5_init_early(void)
+{
+ omap2_set_globals_5xxx();
+ omap5xxx_check_revision();
+ omap_common_init_early();
+}
+#endif
+
void __init omap_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
struct omap_sdrc_params *sdrc_cs1)
{
diff --git a/arch/arm/mach-omap2/iomap.h b/arch/arm/mach-omap2/iomap.h
index 80b8892..cce2b65 100644
--- a/arch/arm/mach-omap2/iomap.h
+++ b/arch/arm/mach-omap2/iomap.h
@@ -1,6 +1,14 @@
/*
* IO mappings for OMAP2+
*
+ * IO definitions for TI OMAP processors and boards
+ *
+ * Copied from arch/arm/mach-sa1100/include/mach/io.h
+ * Copyright (C) 1997-1999 Russell King
+ *
+ * Copyright (C) 2009-2012 Texas Instruments
+ * Added OMAP4/5 support - Santosh Shilimkar <santosh.shilimkar at ti.com>
+ *
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
@@ -166,4 +174,23 @@
/* 0x49000000 --> 0xfb000000 */
#define L4_ABE_44XX_VIRT (L4_ABE_44XX_PHYS + OMAP2_L4_IO_OFFSET)
#define L4_ABE_44XX_SIZE SZ_1M
+/*
+ * ----------------------------------------------------------------------------
+ * Omap5 specific IO mapping
+ * ----------------------------------------------------------------------------
+ */
+#define L3_54XX_PHYS L3_54XX_BASE /* 0x44000000 --> 0xf8000000 */
+#define L3_54XX_VIRT (L3_54XX_PHYS + OMAP4_L3_IO_OFFSET)
+#define L3_54XX_SIZE SZ_1M
+
+#define L4_54XX_PHYS L4_54XX_BASE /* 0x4a000000 --> 0xfc000000 */
+#define L4_54XX_VIRT (L4_54XX_PHYS + OMAP2_L4_IO_OFFSET)
+#define L4_54XX_SIZE SZ_4M
+
+#define L4_WK_54XX_PHYS L4_WK_54XX_BASE /* 0x4ae00000 --> 0xfce00000 */
+#define L4_WK_54XX_VIRT (L4_WK_54XX_PHYS + OMAP2_L4_IO_OFFSET)
+#define L4_WK_54XX_SIZE SZ_2M
+#define L4_PER_54XX_PHYS L4_PER_54XX_BASE /* 0x48000000 --> 0xfa000000 */
+#define L4_PER_54XX_VIRT (L4_PER_54XX_PHYS + OMAP2_L4_IO_OFFSET)
+#define L4_PER_54XX_SIZE SZ_4M
diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c
index ff76ef1..2ada364 100644
--- a/arch/arm/mach-omap2/omap_hwmod.c
+++ b/arch/arm/mach-omap2/omap_hwmod.c
@@ -3619,7 +3619,7 @@ void __init omap_hwmod_init(void)
soc_ops.assert_hardreset = _omap2_assert_hardreset;
soc_ops.deassert_hardreset = _omap2_deassert_hardreset;
soc_ops.is_hardreset_asserted = _omap2_is_hardreset_asserted;
- } else if (cpu_is_omap44xx()) {
+ } else if (cpu_is_omap44xx() || soc_is_omap54xx()) {
soc_ops.enable_module = _omap4_enable_module;
soc_ops.disable_module = _omap4_disable_module;
soc_ops.wait_target_ready = _omap4_wait_target_ready;
diff --git a/arch/arm/mach-omap2/prcm-common.h
b/arch/arm/mach-omap2/prcm-common.h
index 6da3ba4..44485a8 100644
--- a/arch/arm/mach-omap2/prcm-common.h
+++ b/arch/arm/mach-omap2/prcm-common.h
@@ -416,7 +416,7 @@ extern void __iomem *cm_base;
extern void __iomem *cm2_base;
extern void __iomem *prcm_mpu_base;
-#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_ARCH_OMAP5)
+#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5)
extern void omap_prm_base_init(void);
extern void omap_cm_base_init(void);
#else
diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c
index 28cbfb2..053e24e 100644
--- a/arch/arm/mach-omap2/prcm.c
+++ b/arch/arm/mach-omap2/prcm.c
@@ -160,7 +160,7 @@ void __init omap2_set_globals_prcm(struct
omap_globals *omap2_globals)
if (omap2_globals->prcm_mpu)
prcm_mpu_base = omap2_globals->prcm_mpu;
- if (cpu_is_omap44xx()) {
+ if (cpu_is_omap44xx() || soc_is_omap54xx()) {
omap_prm_base_init();
omap_cm_base_init();
}
diff --git a/arch/arm/plat-omap/include/plat/hardware.h
b/arch/arm/plat-omap/include/plat/hardware.h
index e897978..ddbde38 100644
--- a/arch/arm/plat-omap/include/plat/hardware.h
+++ b/arch/arm/plat-omap/include/plat/hardware.h
@@ -288,5 +288,6 @@
#include <plat/omap44xx.h>
#include <plat/ti81xx.h>
#include <plat/am33xx.h>
+#include <plat/omap54xx.h>
#endif /* __ASM_ARCH_OMAP_HARDWARE_H */
diff --git a/arch/arm/plat-omap/include/plat/multi.h
b/arch/arm/plat-omap/include/plat/multi.h
index 999ffba..045e320 100644
--- a/arch/arm/plat-omap/include/plat/multi.h
+++ b/arch/arm/plat-omap/include/plat/multi.h
@@ -99,4 +99,13 @@
# endif
#endif
+#ifdef CONFIG_SOC_OMAP5
+# ifdef OMAP_NAME
+# undef MULTI_OMAP2
+# define MULTI_OMAP2
+# else
+# define OMAP_NAME omap5
+# endif
+#endif
+
#endif /* __PLAT_OMAP_MULTI_H */
diff --git a/arch/arm/plat-omap/include/plat/omap54xx.h
b/arch/arm/plat-omap/include/plat/omap54xx.h
new file mode 100644
index 0000000..a2582bb
--- /dev/null
+++ b/arch/arm/plat-omap/include/plat/omap54xx.h
@@ -0,0 +1,32 @@
+/*:
+ * Address mappings and base address for OMAP5 interconnects
+ * and peripherals.
+ *
+ * Copyright (C) 2012 Texas Instruments
+ * Santosh Shilimkar <santosh.shilimkar at ti.com>
+ * Sricharan <r.sricharan at ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_SOC_OMAP54XX_H
+#define __ASM_SOC_OMAP54XX_H
+
+/*
+ * Please place only base defines here and put the rest in device
+ * specific headers.
+ */
+#define L4_54XX_BASE 0x4a000000
+#define L4_WK_54XX_BASE 0x4ae00000
+#define L4_PER_54XX_BASE 0x48000000
+#define L3_54XX_BASE 0x44000000
+#define OMAP54XX_32KSYNCT_BASE 0x4ae04000
+#define OMAP54XX_CM_CORE_AON_BASE 0x4a004000
+#define OMAP54XX_CM_CORE_BASE 0x4a008000
+#define OMAP54XX_PRM_BASE 0x4ae06000
+#define OMAP54XX_PRCM_MPU_BASE 0x48243000
+#define OMAP54XX_SCM_BASE 0x4a002000
+#define OMAP54XX_CTRL_BASE 0x4a002800
+
+#endif /* __ASM_SOC_OMAP555554XX_H */
diff --git a/arch/arm/plat-omap/include/plat/serial.h
b/arch/arm/plat-omap/include/plat/serial.h
index 28e2d25..65fce44 100644
--- a/arch/arm/plat-omap/include/plat/serial.h
+++ b/arch/arm/plat-omap/include/plat/serial.h
@@ -63,6 +63,14 @@
/* AM33XX serial port */
#define AM33XX_UART1_BASE 0x44E09000
+/* OMAP5 serial ports */
+#define OMAP5_UART1_BASE OMAP2_UART1_BASE
+#define OMAP5_UART2_BASE OMAP2_UART2_BASE
+#define OMAP5_UART3_BASE OMAP4_UART3_BASE
+#define OMAP5_UART4_BASE OMAP4_UART4_BASE
+#define OMAP5_UART5_BASE 0x48066000
+#define OMAP5_UART6_BASE 0x48068000
+
/* External port on Zoom2/3 */
#define ZOOM_UART_BASE 0x10000000
#define ZOOM_UART_VIRT 0xfa400000
@@ -97,6 +105,8 @@
#define TI81XXUART2 82
#define TI81XXUART3 83
#define AM33XXUART1 84
+#define OMAP5UART3 OMAP4UART3
+#define OMAP5UART4 OMAP4UART4
#define ZOOM_UART 95 /* Only on zoom2/3 */
/* This is only used by 8250.c for omap1510 */
diff --git a/arch/arm/plat-omap/include/plat/uncompress.h
b/arch/arm/plat-omap/include/plat/uncompress.h
index ac43233..b8d19a1 100644
--- a/arch/arm/plat-omap/include/plat/uncompress.h
+++ b/arch/arm/plat-omap/include/plat/uncompress.h
@@ -95,6 +95,9 @@ static inline void flush(void)
_DEBUG_LL_ENTRY(mach, OMAP4_UART##p##_BASE, OMAP_PORT_SHIFT, \
OMAP4UART##p)
+#define DEBUG_LL_OMAP5(p, mach) \
+ _DEBUG_LL_ENTRY(mach, OMAP5_UART##p##_BASE, OMAP_PORT_SHIFT, \
+ OMAP5UART##p)
/* Zoom2/3 shift is different for UART1 and external port */
#define DEBUG_LL_ZOOM(mach) \
_DEBUG_LL_ENTRY(mach, ZOOM_UART_BASE, ZOOM_PORT_SHIFT, ZOOM_UART)
@@ -177,6 +180,9 @@ static inline void __arch_decomp_setup(unsigned
long arch_id)
DEBUG_LL_OMAP4(3, omap_4430sdp);
DEBUG_LL_OMAP4(3, omap4_panda);
+ /* omap5 based boards using UART3 */
+ DEBUG_LL_OMAP5(3, omap5_sevm);
+
/* zoom2/3 external uart */
DEBUG_LL_ZOOM(omap_zoom2);
DEBUG_LL_ZOOM(omap_zoom3);
diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c
index 70cf825..766181c 100644
--- a/arch/arm/plat-omap/sram.c
+++ b/arch/arm/plat-omap/sram.c
@@ -6,8 +6,8 @@
* Copyright (C) 2005 Nokia Corporation
* Written by Tony Lindgren <tony at atomide.com>
*
- * Copyright (C) 2009 Texas Instruments
- * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar at ti.com>
+ * Copyright (C) 2009-2012 Texas Instruments
+ * Added OMAP4/5 support - Santosh Shilimkar <santosh.shilimkar at ti.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -44,6 +44,7 @@
#else
#define OMAP4_SRAM_PUB_PA (OMAP4_SRAM_PA + 0x4000)
#endif
+#define OMAP5_SRAM_PA 0x40300000
#if defined(CONFIG_ARCH_OMAP2PLUS)
#define SRAM_BOOTLOADER_SZ 0x00
@@ -118,6 +119,9 @@ static void __init omap_detect_sram(void)
} else if (cpu_is_omap44xx()) {
omap_sram_start = OMAP4_SRAM_PUB_PA;
omap_sram_size = 0xa000; /* 40K */
+ } else if (soc_is_omap54xx()) {
+ omap_sram_start = OMAP5_SRAM_PA;
+ omap_sram_size = SZ_128K; /* 128KB */
} else {
omap_sram_start = OMAP2_SRAM_PUB_PA;
omap_sram_size = 0x800; /* 2K */
@@ -132,6 +136,9 @@ static void __init omap_detect_sram(void)
} else if (cpu_is_omap44xx()) {
omap_sram_start = OMAP4_SRAM_PA;
omap_sram_size = 0xe000; /* 56K */
+ } else if (soc_is_omap54xx()) {
+ omap_sram_start = OMAP5_SRAM_PA;
+ omap_sram_size = SZ_128K; /* 128KB */
} else {
omap_sram_start = OMAP2_SRAM_PA;
if (cpu_is_omap242x())
--
1.7.9.5
More information about the linux-arm-kernel
mailing list