[FOR 3.4 PATCH 5/6] atmel/nand: add DT support
Simon Glass
sjg at chromium.org
Sun Jan 29 13:31:52 EST 2012
Hi,
On Fri, Jan 27, 2012 at 9:10 PM, Jean-Christophe PLAGNIOL-VILLARD
<plagnioj at jcrosoft.com> wrote:
> use a local copy of board informatin and fill with DT data
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre at atmel.com>
> Cc: devicetree-discuss at lists.ozlabs.org
> Cc: linux-mtd at lists.infradead.org
> ---
> .../devicetree/bindings/mtd/atmel-nand.txt | 41 ++++++++
> drivers/mtd/nand/atmel_nand.c | 107 ++++++++++++++++----
> 2 files changed, 130 insertions(+), 18 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/mtd/atmel-nand.txt
>
> diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> new file mode 100644
> index 0000000..a910ab9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> @@ -0,0 +1,41 @@
> +Atmel NAND flash
> +
> +Required properties:
> +- compatible : "atmel,at91rm9200-nand".
> +- reg : should specify localbus address and size used for the chip,
> + and if availlable the ECC.
> +- atmel,nand-addr-offset : offset for the address latch.
> +- atmel,nand-cmd-offset : offset for the command latch.
> +- #address-cells, #size-cells : Must be present if the device has sub-nodes
> + representing partitions.
> +
> +- gpios : specifies the gpio pins to control the NAND device. detect is an
> + optional gpio and may be set to 0 if not present.
What does this mean please? What is 'detect' and what 'control' do the
gpios provide?
Below you have two GPIOs pioC 13 and pioC 14. I think the binding
should document the two GPIOs, the order, and what they are for.
> +
> +Optional properties:
> +- nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default.
> + Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
> + "soft_bch".
> +- nand-bus-width : 8 or 16 bus width if not present 8
> +- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
> +
> +Examples:
> +nand0: nand at 40000000,0 {
> + compatible = "atmel,at91rm9200-nand";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0x40000000 0x10000000
> + 0xffffe800 0x200
> + >;
> + atmel,nand-addr-offset = <21>;
> + atmel,nand-cmd-offset = <22>;
> + nand-on-flash-bbt = <1>;
> + nand-ecc-mode = "soft";
> + gpios = <&pioC 13 0
> + &pioC 14 0
> + 0
Sorry, I haven't seen this before, perhaps it is a standard thing in
Linux. Does 0 mean end of list? Can we not just use the property's
size value for this?
Regards,
Simon
> + >;
> + partition at 0 {
> + ...
> + };
> +};
> diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c
> index d3bde9b..ea7643a 100644
> --- a/drivers/mtd/nand/atmel_nand.c
> +++ b/drivers/mtd/nand/atmel_nand.c
> @@ -27,6 +27,10 @@
> #include <linux/module.h>
> #include <linux/moduleparam.h>
> #include <linux/platform_device.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
> +#include <linux/of_mtd.h>
> #include <linux/mtd/mtd.h>
> #include <linux/mtd/nand.h>
> #include <linux/mtd/partitions.h>
> @@ -83,7 +87,7 @@ struct atmel_nand_host {
> struct mtd_info mtd;
> void __iomem *io_base;
> dma_addr_t io_phys;
> - struct atmel_nand_data *board;
> + struct atmel_nand_data board;
> struct device *dev;
> void __iomem *ecc;
>
> @@ -101,8 +105,8 @@ static int cpu_has_dma(void)
> */
> static void atmel_nand_enable(struct atmel_nand_host *host)
> {
> - if (gpio_is_valid(host->board->enable_pin))
> - gpio_set_value(host->board->enable_pin, 0);
> + if (gpio_is_valid(host->board.enable_pin))
> + gpio_set_value(host->board.enable_pin, 0);
> }
>
> /*
> @@ -110,8 +114,8 @@ static void atmel_nand_enable(struct atmel_nand_host *host)
> */
> static void atmel_nand_disable(struct atmel_nand_host *host)
> {
> - if (gpio_is_valid(host->board->enable_pin))
> - gpio_set_value(host->board->enable_pin, 1);
> + if (gpio_is_valid(host->board.enable_pin))
> + gpio_set_value(host->board.enable_pin, 1);
> }
>
> /*
> @@ -132,9 +136,9 @@ static void atmel_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl
> return;
>
> if (ctrl & NAND_CLE)
> - writeb(cmd, host->io_base + (1 << host->board->cle));
> + writeb(cmd, host->io_base + (1 << host->board.cle));
> else
> - writeb(cmd, host->io_base + (1 << host->board->ale));
> + writeb(cmd, host->io_base + (1 << host->board.ale));
> }
>
> /*
> @@ -145,8 +149,8 @@ static int atmel_nand_device_ready(struct mtd_info *mtd)
> struct nand_chip *nand_chip = mtd->priv;
> struct atmel_nand_host *host = nand_chip->priv;
>
> - return gpio_get_value(host->board->rdy_pin) ^
> - !!host->board->rdy_pin_active_low;
> + return gpio_get_value(host->board.rdy_pin) ^
> + !!host->board.rdy_pin_active_low;
> }
>
> static void dma_complete_func(void *completion)
> @@ -432,6 +436,54 @@ static void atmel_nand_hwctl(struct mtd_info *mtd, int mode)
> }
> }
>
> +static int __devinit atmel_of_init_port(struct atmel_nand_host *host,
> + struct device_node *np)
> +{
> + u32 val;
> + int ecc_mode;
> + struct atmel_nand_data *board = &host->board;
> + enum of_gpio_flags flags;
> +
> + if (of_property_read_u32(np, "atmel,nand-addr-offset", &val) == 0) {
> + if (val >= 32) {
> + dev_err(host->dev, "invalid addr-offset %u\n", val);
> + return -EINVAL;
> + }
> + board->ale = val;
> + }
> +
> + if (of_property_read_u32(np, "atmel,nand-cmd-offset", &val) == 0) {
> + if (val >= 32) {
> + dev_err(host->dev, "invalid cmd-offset %u\n", val);
> + return -EINVAL;
> + }
> + board->cle = val;
> + }
> +
> + ecc_mode = of_get_nand_ecc_mode(np);
> +
> + if (ecc_mode < 0)
> + board->ecc_mode = NAND_ECC_SOFT;
> + else
> + board->ecc_mode = ecc_mode;
> +
> + board->on_flash_bbt = of_get_nand_on_flash_bbt(np);
> +
> + if (of_get_nand_bus_width(np) == 16)
> + board->bus_width_16 = 1;
> +
> + board->rdy_pin = of_get_gpio_flags(np, 0, &flags);
> + if (flags == OF_GPIO_ACTIVE_LOW)
> + board->rdy_pin_active_low = 1;
> + else
> + board->rdy_pin_active_low = 0;
> +
> + board->enable_pin = of_get_gpio(np, 1);
> + board->det_pin = of_get_gpio(np, 2);
> +
> + return 0;
> +}
> +
> /*
> * Probe for the NAND device.
> */
> @@ -442,6 +494,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
> struct nand_chip *nand_chip;
> struct resource *regs;
> struct resource *mem;
> + struct mtd_part_parser_data ppdata = {};
> int res;
>
> mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> @@ -468,8 +521,15 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
>
> mtd = &host->mtd;
> nand_chip = &host->nand_chip;
> - host->board = pdev->dev.platform_data;
> host->dev = &pdev->dev;
> + if (pdev->dev.of_node) {
> + res = atmel_of_init_port(host, pdev->dev.of_node);
> + if (res)
> + goto err_nand_ioremap;
> + } else {
> + memcpy(&host->board, pdev->dev.platform_data,
> + sizeof(struct atmel_nand_data));
> + }
>
> nand_chip->priv = host; /* link the private data structures */
> mtd->priv = nand_chip;
> @@ -480,10 +540,10 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
> nand_chip->IO_ADDR_W = host->io_base;
> nand_chip->cmd_ctrl = atmel_nand_cmd_ctrl;
>
> - if (gpio_is_valid(host->board->rdy_pin))
> + if (gpio_is_valid(host->board.rdy_pin))
> nand_chip->dev_ready = atmel_nand_device_ready;
>
> - nand_chip->ecc.mode = host->board->ecc_mode;
> + nand_chip->ecc.mode = host->board.ecc_mode;
>
> regs = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> if (!regs && nand_chip->ecc.mode == NAND_ECC_HW) {
> @@ -508,7 +568,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
>
> nand_chip->chip_delay = 20; /* 20us command delay time */
>
> - if (host->board->bus_width_16) /* 16-bit bus width */
> + if (host->board.bus_width_16) /* 16-bit bus width */
> nand_chip->options |= NAND_BUSWIDTH_16;
>
> nand_chip->read_buf = atmel_read_buf;
> @@ -517,15 +577,15 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
> platform_set_drvdata(pdev, host);
> atmel_nand_enable(host);
>
> - if (gpio_is_valid(host->board->det_pin)) {
> - if (gpio_get_value(host->board->det_pin)) {
> + if (gpio_is_valid(host->board.det_pin)) {
> + if (gpio_get_value(host->board.det_pin)) {
> printk(KERN_INFO "No SmartMedia card inserted.\n");
> res = -ENXIO;
> goto err_no_card;
> }
> }
>
> - if (host->board->on_flash_bbt || on_flash_bbt) {
> + if (host->board.on_flash_bbt || on_flash_bbt) {
> printk(KERN_INFO "atmel_nand: Use On Flash BBT\n");
> nand_chip->bbt_options |= NAND_BBT_USE_FLASH;
> }
> @@ -600,8 +660,9 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
> }
>
> mtd->name = "atmel_nand";
> - res = mtd_device_parse_register(mtd, NULL, 0,
> - host->board->parts, host->board->num_parts);
> + ppdata.of_node = pdev->dev.of_node;
> + res = mtd_device_parse_register(mtd, NULL, &ppdata,
> + host->board.parts, host->board.num_parts);
> if (!res)
> return res;
>
> @@ -645,11 +706,21 @@ static int __exit atmel_nand_remove(struct platform_device *pdev)
> return 0;
> }
>
> +#if defined(CONFIG_OF)
> +static const struct of_device_id atmel_nand_dt_ids[] = {
> + { .compatible = "atmel,at91rm9200-nand" },
> + { /* sentinel */ }
> +};
> +
> +MODULE_DEVICE_TABLE(of, atmel_nand_dt_ids);
> +#endif
> +
> static struct platform_driver atmel_nand_driver = {
> .remove = __exit_p(atmel_nand_remove),
> .driver = {
> .name = "atmel_nand",
> .owner = THIS_MODULE,
> + .of_match_table = of_match_ptr(atmel_nand_dt_ids),
> },
> };
>
> --
> 1.7.7
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
More information about the linux-arm-kernel
mailing list