[PATCH] ARM: at91: removal of CAP9 SoC family
Jean-Christophe PLAGNIOL-VILLARD
plagnioj at jcrosoft.com
Thu Jan 26 08:07:09 EST 2012
Atmel CAP9 family is not maintained well and products may be
difficult to find now. It will allow to save workforce and
remove LOC during current cleanup process.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre at atmel.com>
---
Documentation/feature-removal-schedule.txt | 14 -
arch/arm/Kconfig | 2 +-
arch/arm/Kconfig.debug | 2 +-
arch/arm/configs/at91cap9_defconfig | 108 --
arch/arm/mach-at91/Kconfig | 26 +-
arch/arm/mach-at91/Makefile | 4 -
arch/arm/mach-at91/Makefile.boot | 6 +-
arch/arm/mach-at91/at91cap9.c | 396 -------
arch/arm/mach-at91/at91cap9_devices.c | 1273 ---------------------
arch/arm/mach-at91/board-cap9adk.c | 396 -------
arch/arm/mach-at91/clock.c | 5 +-
arch/arm/mach-at91/generic.h | 1 -
arch/arm/mach-at91/include/mach/at91_pmc.h | 16 +-
arch/arm/mach-at91/include/mach/at91cap9.h | 122 --
arch/arm/mach-at91/include/mach/at91cap9_matrix.h | 137 ---
arch/arm/mach-at91/include/mach/at91sam9_ddrsdr.h | 10 -
arch/arm/mach-at91/include/mach/cpu.h | 21 -
arch/arm/mach-at91/include/mach/hardware.h | 4 +-
arch/arm/mach-at91/pm.c | 5 -
arch/arm/mach-at91/pm.h | 18 -
arch/arm/mach-at91/pm_slowclock.S | 12 +-
arch/arm/mach-at91/setup.c | 17 -
arch/arm/mach-at91/soc.h | 5 -
arch/avr32/mach-at32ap/include/mach/cpu.h | 3 -
drivers/mmc/host/at91_mci.c | 1 -
drivers/usb/gadget/Kconfig | 4 +-
26 files changed, 18 insertions(+), 2590 deletions(-)
delete mode 100644 arch/arm/configs/at91cap9_defconfig
delete mode 100644 arch/arm/mach-at91/at91cap9.c
delete mode 100644 arch/arm/mach-at91/at91cap9_devices.c
delete mode 100644 arch/arm/mach-at91/board-cap9adk.c
delete mode 100644 arch/arm/mach-at91/include/mach/at91cap9.h
delete mode 100644 arch/arm/mach-at91/include/mach/at91cap9_matrix.h
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt
index a0ffac0..1bea46a 100644
--- a/Documentation/feature-removal-schedule.txt
+++ b/Documentation/feature-removal-schedule.txt
@@ -510,17 +510,3 @@ Why: The pci_scan_bus_parented() interface creates a new root bus. The
convert to using pci_scan_root_bus() so they can supply a list of
bus resources when the bus is created.
Who: Bjorn Helgaas <bhelgaas at google.com>
-
-----------------------------
-
-What: The CAP9 SoC family will be removed
-When: 3.4
-Files: arch/arm/mach-at91/at91cap9.c
- arch/arm/mach-at91/at91cap9_devices.c
- arch/arm/mach-at91/include/mach/at91cap9.h
- arch/arm/mach-at91/include/mach/at91cap9_matrix.h
- arch/arm/mach-at91/include/mach/at91cap9_ddrsdr.h
- arch/arm/mach-at91/board-cap9adk.c
-Why: The code is not actively maintained and platforms are now hard to find.
-Who: Nicolas Ferre <nicolas.ferre at atmel.com>
- Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index b0d8c6a..c0a13aa 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -325,7 +325,7 @@ config ARCH_AT91
select IRQ_DOMAIN
help
This enables support for systems based on the Atmel AT91RM9200,
- AT91SAM9 and AT91CAP9 processors.
+ AT91SAM9 processors.
config ARCH_BCMRING
bool "Broadcom BCMRING"
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index e0d236d..d0a9118 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -105,7 +105,7 @@ choice
depends on HAVE_AT91_DBGU0
config AT91_DEBUG_LL_DBGU1
- bool "Kernel low-level debugging on 9263, 9g45 and cap9"
+ bool "Kernel low-level debugging on 9263 and 9g45"
depends on HAVE_AT91_DBGU1
config DEBUG_FOOTBRIDGE_COM1
diff --git a/arch/arm/configs/at91cap9_defconfig b/arch/arm/configs/at91cap9_defconfig
deleted file mode 100644
index 8826eb2..0000000
--- a/arch/arm/configs/at91cap9_defconfig
+++ /dev/null
@@ -1,108 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-# CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_AT91=y
-CONFIG_ARCH_AT91CAP9=y
-CONFIG_MACH_AT91CAP9ADK=y
-CONFIG_MTD_AT91_DATAFLASH_CARD=y
-CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_AEABI=y
-CONFIG_LEDS=y
-CONFIG_LEDS_CPU=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/ram0 rw"
-CONFIG_FPE_NWFPE=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_JEDECPROBE=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_DATAFLASH=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ATMEL=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_SCSI_MULTI_LUN=y
-CONFIG_NETDEVICES=y
-CONFIG_MII=y
-CONFIG_MACB=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_ADS7846=y
-# CONFIG_SERIO is not set
-CONFIG_SERIAL_ATMEL=y
-CONFIG_SERIAL_ATMEL_CONSOLE=y
-CONFIG_HW_RANDOM=y
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_SPI=y
-CONFIG_SPI_ATMEL=y
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_WATCHDOG_NOWAYOUT=y
-CONFIG_FB=y
-CONFIG_FB_ATMEL=y
-CONFIG_LOGO=y
-# CONFIG_LOGO_LINUX_MONO is not set
-# CONFIG_LOGO_LINUX_CLUT224 is not set
-# CONFIG_USB_HID is not set
-CONFIG_USB=y
-CONFIG_USB_DEVICEFS=y
-CONFIG_USB_MON=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_ETH=m
-CONFIG_USB_FILE_STORAGE=m
-CONFIG_MMC=y
-CONFIG_MMC_AT91=m
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_AT91SAM9=y
-CONFIG_EXT2_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_CRAMFS=y
-CONFIG_NFS_FS=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_USER=y
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index f7fdd17..aca2d69 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -111,15 +111,6 @@ config ARCH_AT91SAM9X5
select HAVE_AT91_DBGU0
select AT91_SAM9G45_RESET
-config ARCH_AT91CAP9
- bool "AT91CAP9"
- select CPU_ARM926T
- select GENERIC_CLOCKEVENTS
- select HAVE_FB_ATMEL
- select HAVE_NET_MACB
- select HAVE_AT91_DBGU1
- select AT91_SAM9G45_RESET
-
config ARCH_AT91X40
bool "AT91x40"
select ARCH_USES_GETTIMEOFFSET
@@ -456,21 +447,6 @@ endif
# ----------------------------------------------------------
-if ARCH_AT91CAP9
-
-comment "AT91CAP9 Board Type"
-
-config MACH_AT91CAP9ADK
- bool "Atmel AT91CAP9A-DK Evaluation Kit"
- select HAVE_AT91_DATAFLASH_CARD
- help
- Select this if you are using Atmel's AT91CAP9A-DK Evaluation Kit.
- <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4138>
-
-endif
-
-# ----------------------------------------------------------
-
if ARCH_AT91X40
comment "AT91X40 Board Type"
@@ -553,7 +529,7 @@ config AT91_EARLY_DBGU0
depends on HAVE_AT91_DBGU0
config AT91_EARLY_DBGU1
- bool "DBGU on 9263, 9g45 and cap9"
+ bool "DBGU on 9263 and 9g45"
depends on HAVE_AT91_DBGU1
config AT91_EARLY_USART0
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 7b7ab6e..1b65185 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -21,7 +21,6 @@ obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl.o at91sam926x_time.o at91sam9rl_devi
obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o
obj-$(CONFIG_ARCH_AT91SAM9G45) += at91sam9g45.o at91sam926x_time.o at91sam9g45_devices.o sam9_smc.o
obj-$(CONFIG_ARCH_AT91SAM9X5) += at91sam9x5.o at91sam926x_time.o
-obj-$(CONFIG_ARCH_AT91CAP9) += at91cap9.o at91sam926x_time.o at91cap9_devices.o sam9_smc.o
obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o
# AT91RM9200 board-specific support
@@ -82,9 +81,6 @@ obj-$(CONFIG_MACH_AT91SAM9M10G45EK) += board-sam9m10g45ek.o
# AT91SAM board with device-tree
obj-$(CONFIG_MACH_AT91SAM_DT) += board-dt.o
-# AT91CAP9 board-specific support
-obj-$(CONFIG_MACH_AT91CAP9ADK) += board-cap9adk.o
-
# AT91X40 board-specific support
obj-$(CONFIG_MACH_AT91EB01) += board-eb01.o
diff --git a/arch/arm/mach-at91/Makefile.boot b/arch/arm/mach-at91/Makefile.boot
index 8ddafad..2fd051e 100644
--- a/arch/arm/mach-at91/Makefile.boot
+++ b/arch/arm/mach-at91/Makefile.boot
@@ -3,11 +3,7 @@
# PARAMS_PHYS must be within 4MB of ZRELADDR
# INITRD_PHYS must be in RAM
-ifeq ($(CONFIG_ARCH_AT91CAP9),y)
- zreladdr-y += 0x70008000
-params_phys-y := 0x70000100
-initrd_phys-y := 0x70410000
-else ifeq ($(CONFIG_ARCH_AT91SAM9G45),y)
+ifeq ($(CONFIG_ARCH_AT91SAM9G45),y)
zreladdr-y += 0x70008000
params_phys-y := 0x70000100
initrd_phys-y := 0x70410000
diff --git a/arch/arm/mach-at91/at91cap9.c b/arch/arm/mach-at91/at91cap9.c
deleted file mode 100644
index a42edc2..0000000
--- a/arch/arm/mach-at91/at91cap9.c
+++ /dev/null
@@ -1,396 +0,0 @@
-/*
- * arch/arm/mach-at91/at91cap9.c
- *
- * Copyright (C) 2007 Stelian Pop <stelian.pop at leadtechdesign.com>
- * Copyright (C) 2007 Lead Tech Design <www.leadtechdesign.com>
- * Copyright (C) 2007 Atmel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-
-#include <linux/module.h>
-
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <mach/cpu.h>
-#include <mach/at91cap9.h>
-#include <mach/at91_pmc.h>
-
-#include "soc.h"
-#include "generic.h"
-#include "clock.h"
-#include "sam9_smc.h"
-
-/* --------------------------------------------------------------------
- * Clocks
- * -------------------------------------------------------------------- */
-
-/*
- * The peripheral clocks.
- */
-static struct clk pioABCD_clk = {
- .name = "pioABCD_clk",
- .pmc_mask = 1 << AT91CAP9_ID_PIOABCD,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk mpb0_clk = {
- .name = "mpb0_clk",
- .pmc_mask = 1 << AT91CAP9_ID_MPB0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk mpb1_clk = {
- .name = "mpb1_clk",
- .pmc_mask = 1 << AT91CAP9_ID_MPB1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk mpb2_clk = {
- .name = "mpb2_clk",
- .pmc_mask = 1 << AT91CAP9_ID_MPB2,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk mpb3_clk = {
- .name = "mpb3_clk",
- .pmc_mask = 1 << AT91CAP9_ID_MPB3,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk mpb4_clk = {
- .name = "mpb4_clk",
- .pmc_mask = 1 << AT91CAP9_ID_MPB4,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart0_clk = {
- .name = "usart0_clk",
- .pmc_mask = 1 << AT91CAP9_ID_US0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart1_clk = {
- .name = "usart1_clk",
- .pmc_mask = 1 << AT91CAP9_ID_US1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart2_clk = {
- .name = "usart2_clk",
- .pmc_mask = 1 << AT91CAP9_ID_US2,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc0_clk = {
- .name = "mci0_clk",
- .pmc_mask = 1 << AT91CAP9_ID_MCI0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc1_clk = {
- .name = "mci1_clk",
- .pmc_mask = 1 << AT91CAP9_ID_MCI1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk can_clk = {
- .name = "can_clk",
- .pmc_mask = 1 << AT91CAP9_ID_CAN,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi_clk = {
- .name = "twi_clk",
- .pmc_mask = 1 << AT91CAP9_ID_TWI,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi0_clk = {
- .name = "spi0_clk",
- .pmc_mask = 1 << AT91CAP9_ID_SPI0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi1_clk = {
- .name = "spi1_clk",
- .pmc_mask = 1 << AT91CAP9_ID_SPI1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc0_clk = {
- .name = "ssc0_clk",
- .pmc_mask = 1 << AT91CAP9_ID_SSC0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc1_clk = {
- .name = "ssc1_clk",
- .pmc_mask = 1 << AT91CAP9_ID_SSC1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ac97_clk = {
- .name = "ac97_clk",
- .pmc_mask = 1 << AT91CAP9_ID_AC97C,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk tcb_clk = {
- .name = "tcb_clk",
- .pmc_mask = 1 << AT91CAP9_ID_TCB,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk pwm_clk = {
- .name = "pwm_clk",
- .pmc_mask = 1 << AT91CAP9_ID_PWMC,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk macb_clk = {
- .name = "pclk",
- .pmc_mask = 1 << AT91CAP9_ID_EMAC,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk aestdes_clk = {
- .name = "aestdes_clk",
- .pmc_mask = 1 << AT91CAP9_ID_AESTDES,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk adc_clk = {
- .name = "adc_clk",
- .pmc_mask = 1 << AT91CAP9_ID_ADC,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk isi_clk = {
- .name = "isi_clk",
- .pmc_mask = 1 << AT91CAP9_ID_ISI,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk lcdc_clk = {
- .name = "lcdc_clk",
- .pmc_mask = 1 << AT91CAP9_ID_LCDC,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk dma_clk = {
- .name = "dma_clk",
- .pmc_mask = 1 << AT91CAP9_ID_DMA,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk udphs_clk = {
- .name = "udphs_clk",
- .pmc_mask = 1 << AT91CAP9_ID_UDPHS,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ohci_clk = {
- .name = "ohci_clk",
- .pmc_mask = 1 << AT91CAP9_ID_UHP,
- .type = CLK_TYPE_PERIPHERAL,
-};
-
-static struct clk *periph_clocks[] __initdata = {
- &pioABCD_clk,
- &mpb0_clk,
- &mpb1_clk,
- &mpb2_clk,
- &mpb3_clk,
- &mpb4_clk,
- &usart0_clk,
- &usart1_clk,
- &usart2_clk,
- &mmc0_clk,
- &mmc1_clk,
- &can_clk,
- &twi_clk,
- &spi0_clk,
- &spi1_clk,
- &ssc0_clk,
- &ssc1_clk,
- &ac97_clk,
- &tcb_clk,
- &pwm_clk,
- &macb_clk,
- &aestdes_clk,
- &adc_clk,
- &isi_clk,
- &lcdc_clk,
- &dma_clk,
- &udphs_clk,
- &ohci_clk,
- // irq0 .. irq1
-};
-
-static struct clk_lookup periph_clocks_lookups[] = {
- /* One additional fake clock for macb_hclk */
- CLKDEV_CON_ID("hclk", &macb_clk),
- CLKDEV_CON_DEV_ID("hclk", "atmel_usba_udc", &utmi_clk),
- CLKDEV_CON_DEV_ID("pclk", "atmel_usba_udc", &udphs_clk),
- CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk),
- CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1", &mmc1_clk),
- CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
- CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
- CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk),
- CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
- CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
- /* fake hclk clock */
- CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
- CLKDEV_CON_ID("pioA", &pioABCD_clk),
- CLKDEV_CON_ID("pioB", &pioABCD_clk),
- CLKDEV_CON_ID("pioC", &pioABCD_clk),
- CLKDEV_CON_ID("pioD", &pioABCD_clk),
-};
-
-static struct clk_lookup usart_clocks_lookups[] = {
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
-};
-
-/*
- * The four programmable clocks.
- * You must configure pin multiplexing to bring these signals out.
- */
-static struct clk pck0 = {
- .name = "pck0",
- .pmc_mask = AT91_PMC_PCK0,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 0,
-};
-static struct clk pck1 = {
- .name = "pck1",
- .pmc_mask = AT91_PMC_PCK1,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 1,
-};
-static struct clk pck2 = {
- .name = "pck2",
- .pmc_mask = AT91_PMC_PCK2,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 2,
-};
-static struct clk pck3 = {
- .name = "pck3",
- .pmc_mask = AT91_PMC_PCK3,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 3,
-};
-
-static void __init at91cap9_register_clocks(void)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
- clk_register(periph_clocks[i]);
-
- clkdev_add_table(periph_clocks_lookups,
- ARRAY_SIZE(periph_clocks_lookups));
- clkdev_add_table(usart_clocks_lookups,
- ARRAY_SIZE(usart_clocks_lookups));
-
- clk_register(&pck0);
- clk_register(&pck1);
- clk_register(&pck2);
- clk_register(&pck3);
-}
-
-static struct clk_lookup console_clock_lookup;
-
-void __init at91cap9_set_console_clock(int id)
-{
- if (id >= ARRAY_SIZE(usart_clocks_lookups))
- return;
-
- console_clock_lookup.con_id = "usart";
- console_clock_lookup.clk = usart_clocks_lookups[id].clk;
- clkdev_add(&console_clock_lookup);
-}
-
-/* --------------------------------------------------------------------
- * GPIO
- * -------------------------------------------------------------------- */
-
-static struct at91_gpio_bank at91cap9_gpio[] __initdata = {
- {
- .id = AT91CAP9_ID_PIOABCD,
- .regbase = AT91CAP9_BASE_PIOA,
- }, {
- .id = AT91CAP9_ID_PIOABCD,
- .regbase = AT91CAP9_BASE_PIOB,
- }, {
- .id = AT91CAP9_ID_PIOABCD,
- .regbase = AT91CAP9_BASE_PIOC,
- }, {
- .id = AT91CAP9_ID_PIOABCD,
- .regbase = AT91CAP9_BASE_PIOD,
- }
-};
-
-/* --------------------------------------------------------------------
- * AT91CAP9 processor initialization
- * -------------------------------------------------------------------- */
-
-static void __init at91cap9_map_io(void)
-{
- at91_init_sram(0, AT91CAP9_SRAM_BASE, AT91CAP9_SRAM_SIZE);
-}
-
-static void __init at91cap9_ioremap_registers(void)
-{
- at91_ioremap_shdwc(AT91CAP9_BASE_SHDWC);
- at91_ioremap_rstc(AT91CAP9_BASE_RSTC);
- at91sam926x_ioremap_pit(AT91CAP9_BASE_PIT);
- at91sam9_ioremap_smc(0, AT91CAP9_BASE_SMC);
-}
-
-static void __init at91cap9_initialize(void)
-{
- arm_pm_restart = at91sam9g45_restart;
- at91_extern_irq = (1 << AT91CAP9_ID_IRQ0) | (1 << AT91CAP9_ID_IRQ1);
-
- /* Register GPIO subsystem */
- at91_gpio_init(at91cap9_gpio, 4);
-
- /* Remember the silicon revision */
- if (cpu_is_at91cap9_revB())
- system_rev = 0xB;
- else if (cpu_is_at91cap9_revC())
- system_rev = 0xC;
-}
-
-/* --------------------------------------------------------------------
- * Interrupt initialization
- * -------------------------------------------------------------------- */
-
-/*
- * The default interrupt priority levels (0 = lowest, 7 = highest).
- */
-static unsigned int at91cap9_default_irq_priority[NR_AIC_IRQS] __initdata = {
- 7, /* Advanced Interrupt Controller (FIQ) */
- 7, /* System Peripherals */
- 1, /* Parallel IO Controller A, B, C and D */
- 0, /* MP Block Peripheral 0 */
- 0, /* MP Block Peripheral 1 */
- 0, /* MP Block Peripheral 2 */
- 0, /* MP Block Peripheral 3 */
- 0, /* MP Block Peripheral 4 */
- 5, /* USART 0 */
- 5, /* USART 1 */
- 5, /* USART 2 */
- 0, /* Multimedia Card Interface 0 */
- 0, /* Multimedia Card Interface 1 */
- 3, /* CAN */
- 6, /* Two-Wire Interface */
- 5, /* Serial Peripheral Interface 0 */
- 5, /* Serial Peripheral Interface 1 */
- 4, /* Serial Synchronous Controller 0 */
- 4, /* Serial Synchronous Controller 1 */
- 5, /* AC97 Controller */
- 0, /* Timer Counter 0, 1 and 2 */
- 0, /* Pulse Width Modulation Controller */
- 3, /* Ethernet */
- 0, /* Advanced Encryption Standard, Triple DES*/
- 0, /* Analog-to-Digital Converter */
- 0, /* Image Sensor Interface */
- 3, /* LCD Controller */
- 0, /* DMA Controller */
- 2, /* USB Device Port */
- 2, /* USB Host port */
- 0, /* Advanced Interrupt Controller (IRQ0) */
- 0, /* Advanced Interrupt Controller (IRQ1) */
-};
-
-struct at91_init_soc __initdata at91cap9_soc = {
- .map_io = at91cap9_map_io,
- .default_irq_priority = at91cap9_default_irq_priority,
- .ioremap_registers = at91cap9_ioremap_registers,
- .register_clocks = at91cap9_register_clocks,
- .init = at91cap9_initialize,
-};
diff --git a/arch/arm/mach-at91/at91cap9_devices.c b/arch/arm/mach-at91/at91cap9_devices.c
deleted file mode 100644
index d298fb7..0000000
--- a/arch/arm/mach-at91/at91cap9_devices.c
+++ /dev/null
@@ -1,1273 +0,0 @@
-/*
- * arch/arm/mach-at91/at91cap9_devices.c
- *
- * Copyright (C) 2007 Stelian Pop <stelian.pop at leadtechdesign.com>
- * Copyright (C) 2007 Lead Tech Design <www.leadtechdesign.com>
- * Copyright (C) 2007 Atmel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/i2c-gpio.h>
-
-#include <video/atmel_lcdc.h>
-
-#include <mach/board.h>
-#include <mach/cpu.h>
-#include <mach/at91cap9.h>
-#include <mach/at91cap9_matrix.h>
-#include <mach/at91sam9_smc.h>
-
-#include "generic.h"
-
-
-/* --------------------------------------------------------------------
- * USB Host
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static u64 ohci_dmamask = DMA_BIT_MASK(32);
-static struct at91_usbh_data usbh_data;
-
-static struct resource usbh_resources[] = {
- [0] = {
- .start = AT91CAP9_UHP_BASE,
- .end = AT91CAP9_UHP_BASE + SZ_1M - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_UHP,
- .end = AT91CAP9_ID_UHP,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91_usbh_device = {
- .name = "at91_ohci",
- .id = -1,
- .dev = {
- .dma_mask = &ohci_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &usbh_data,
- },
- .resource = usbh_resources,
- .num_resources = ARRAY_SIZE(usbh_resources),
-};
-
-void __init at91_add_device_usbh(struct at91_usbh_data *data)
-{
- int i;
-
- if (!data)
- return;
-
- if (cpu_is_at91cap9_revB())
- irq_set_irq_type(AT91CAP9_ID_UHP, IRQ_TYPE_LEVEL_HIGH);
-
- /* Enable VBus control for UHP ports */
- for (i = 0; i < data->ports; i++) {
- if (gpio_is_valid(data->vbus_pin[i]))
- at91_set_gpio_output(data->vbus_pin[i], 0);
- }
-
- /* Enable overcurrent notification */
- for (i = 0; i < data->ports; i++) {
- if (data->overcurrent_pin[i])
- at91_set_gpio_input(data->overcurrent_pin[i], 1);
- }
-
- usbh_data = *data;
- platform_device_register(&at91_usbh_device);
-}
-#else
-void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * USB HS Device (Gadget)
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_ATMEL_USBA) || defined(CONFIG_USB_ATMEL_USBA_MODULE)
-
-static struct resource usba_udc_resources[] = {
- [0] = {
- .start = AT91CAP9_UDPHS_FIFO,
- .end = AT91CAP9_UDPHS_FIFO + SZ_512K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_BASE_UDPHS,
- .end = AT91CAP9_BASE_UDPHS + SZ_1K - 1,
- .flags = IORESOURCE_MEM,
- },
- [2] = {
- .start = AT91CAP9_ID_UDPHS,
- .end = AT91CAP9_ID_UDPHS,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-#define EP(nam, idx, maxpkt, maxbk, dma, isoc) \
- [idx] = { \
- .name = nam, \
- .index = idx, \
- .fifo_size = maxpkt, \
- .nr_banks = maxbk, \
- .can_dma = dma, \
- .can_isoc = isoc, \
- }
-
-static struct usba_ep_data usba_udc_ep[] = {
- EP("ep0", 0, 64, 1, 0, 0),
- EP("ep1", 1, 1024, 3, 1, 1),
- EP("ep2", 2, 1024, 3, 1, 1),
- EP("ep3", 3, 1024, 2, 1, 1),
- EP("ep4", 4, 1024, 2, 1, 1),
- EP("ep5", 5, 1024, 2, 1, 0),
- EP("ep6", 6, 1024, 2, 1, 0),
- EP("ep7", 7, 1024, 2, 0, 0),
-};
-
-#undef EP
-
-/*
- * pdata doesn't have room for any endpoints, so we need to
- * append room for the ones we need right after it.
- */
-static struct {
- struct usba_platform_data pdata;
- struct usba_ep_data ep[8];
-} usba_udc_data;
-
-static struct platform_device at91_usba_udc_device = {
- .name = "atmel_usba_udc",
- .id = -1,
- .dev = {
- .platform_data = &usba_udc_data.pdata,
- },
- .resource = usba_udc_resources,
- .num_resources = ARRAY_SIZE(usba_udc_resources),
-};
-
-void __init at91_add_device_usba(struct usba_platform_data *data)
-{
- if (cpu_is_at91cap9_revB()) {
- irq_set_irq_type(AT91CAP9_ID_UDPHS, IRQ_TYPE_LEVEL_HIGH);
- at91_sys_write(AT91_MATRIX_UDPHS, AT91_MATRIX_SELECT_UDPHS |
- AT91_MATRIX_UDPHS_BYPASS_LOCK);
- }
- else
- at91_sys_write(AT91_MATRIX_UDPHS, AT91_MATRIX_SELECT_UDPHS);
-
- /*
- * Invalid pins are 0 on AT91, but the usba driver is shared
- * with AVR32, which use negative values instead. Once/if
- * gpio_is_valid() is ported to AT91, revisit this code.
- */
- usba_udc_data.pdata.vbus_pin = -EINVAL;
- usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
- memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
-
- if (data && gpio_is_valid(data->vbus_pin)) {
- at91_set_gpio_input(data->vbus_pin, 0);
- at91_set_deglitch(data->vbus_pin, 1);
- usba_udc_data.pdata.vbus_pin = data->vbus_pin;
- }
-
- /* Pullup pin is handled internally by USB device peripheral */
-
- platform_device_register(&at91_usba_udc_device);
-}
-#else
-void __init at91_add_device_usba(struct usba_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * Ethernet
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
-static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct macb_platform_data eth_data;
-
-static struct resource eth_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_EMAC,
- .end = AT91CAP9_BASE_EMAC + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_EMAC,
- .end = AT91CAP9_ID_EMAC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91cap9_eth_device = {
- .name = "macb",
- .id = -1,
- .dev = {
- .dma_mask = ð_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = ð_data,
- },
- .resource = eth_resources,
- .num_resources = ARRAY_SIZE(eth_resources),
-};
-
-void __init at91_add_device_eth(struct macb_platform_data *data)
-{
- if (!data)
- return;
-
- if (gpio_is_valid(data->phy_irq_pin)) {
- at91_set_gpio_input(data->phy_irq_pin, 0);
- at91_set_deglitch(data->phy_irq_pin, 1);
- }
-
- /* Pins used for MII and RMII */
- at91_set_A_periph(AT91_PIN_PB21, 0); /* ETXCK_EREFCK */
- at91_set_A_periph(AT91_PIN_PB22, 0); /* ERXDV */
- at91_set_A_periph(AT91_PIN_PB25, 0); /* ERX0 */
- at91_set_A_periph(AT91_PIN_PB26, 0); /* ERX1 */
- at91_set_A_periph(AT91_PIN_PB27, 0); /* ERXER */
- at91_set_A_periph(AT91_PIN_PB28, 0); /* ETXEN */
- at91_set_A_periph(AT91_PIN_PB23, 0); /* ETX0 */
- at91_set_A_periph(AT91_PIN_PB24, 0); /* ETX1 */
- at91_set_A_periph(AT91_PIN_PB30, 0); /* EMDIO */
- at91_set_A_periph(AT91_PIN_PB29, 0); /* EMDC */
-
- if (!data->is_rmii) {
- at91_set_B_periph(AT91_PIN_PC25, 0); /* ECRS */
- at91_set_B_periph(AT91_PIN_PC26, 0); /* ECOL */
- at91_set_B_periph(AT91_PIN_PC22, 0); /* ERX2 */
- at91_set_B_periph(AT91_PIN_PC23, 0); /* ERX3 */
- at91_set_B_periph(AT91_PIN_PC27, 0); /* ERXCK */
- at91_set_B_periph(AT91_PIN_PC20, 0); /* ETX2 */
- at91_set_B_periph(AT91_PIN_PC21, 0); /* ETX3 */
- at91_set_B_periph(AT91_PIN_PC24, 0); /* ETXER */
- }
-
- eth_data = *data;
- platform_device_register(&at91cap9_eth_device);
-}
-#else
-void __init at91_add_device_eth(struct macb_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * MMC / SD
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
-static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct at91_mmc_data mmc0_data, mmc1_data;
-
-static struct resource mmc0_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_MCI0,
- .end = AT91CAP9_BASE_MCI0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_MCI0,
- .end = AT91CAP9_ID_MCI0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91cap9_mmc0_device = {
- .name = "at91_mci",
- .id = 0,
- .dev = {
- .dma_mask = &mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &mmc0_data,
- },
- .resource = mmc0_resources,
- .num_resources = ARRAY_SIZE(mmc0_resources),
-};
-
-static struct resource mmc1_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_MCI1,
- .end = AT91CAP9_BASE_MCI1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_MCI1,
- .end = AT91CAP9_ID_MCI1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91cap9_mmc1_device = {
- .name = "at91_mci",
- .id = 1,
- .dev = {
- .dma_mask = &mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &mmc1_data,
- },
- .resource = mmc1_resources,
- .num_resources = ARRAY_SIZE(mmc1_resources),
-};
-
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
-{
- if (!data)
- return;
-
- /* input/irq */
- if (gpio_is_valid(data->det_pin)) {
- at91_set_gpio_input(data->det_pin, 1);
- at91_set_deglitch(data->det_pin, 1);
- }
- if (gpio_is_valid(data->wp_pin))
- at91_set_gpio_input(data->wp_pin, 1);
- if (gpio_is_valid(data->vcc_pin))
- at91_set_gpio_output(data->vcc_pin, 0);
-
- if (mmc_id == 0) { /* MCI0 */
- /* CLK */
- at91_set_A_periph(AT91_PIN_PA2, 0);
-
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA1, 1);
-
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA0, 1);
- if (data->wire4) {
- at91_set_A_periph(AT91_PIN_PA3, 1);
- at91_set_A_periph(AT91_PIN_PA4, 1);
- at91_set_A_periph(AT91_PIN_PA5, 1);
- }
-
- mmc0_data = *data;
- platform_device_register(&at91cap9_mmc0_device);
- } else { /* MCI1 */
- /* CLK */
- at91_set_A_periph(AT91_PIN_PA16, 0);
-
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA17, 1);
-
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA18, 1);
- if (data->wire4) {
- at91_set_A_periph(AT91_PIN_PA19, 1);
- at91_set_A_periph(AT91_PIN_PA20, 1);
- at91_set_A_periph(AT91_PIN_PA21, 1);
- }
-
- mmc1_data = *data;
- platform_device_register(&at91cap9_mmc1_device);
- }
-}
-#else
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * NAND / SmartMedia
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
-static struct atmel_nand_data nand_data;
-
-#define NAND_BASE AT91_CHIPSELECT_3
-
-static struct resource nand_resources[] = {
- [0] = {
- .start = NAND_BASE,
- .end = NAND_BASE + SZ_256M - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_BASE_ECC,
- .end = AT91CAP9_BASE_ECC + SZ_512 - 1,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct platform_device at91cap9_nand_device = {
- .name = "atmel_nand",
- .id = -1,
- .dev = {
- .platform_data = &nand_data,
- },
- .resource = nand_resources,
- .num_resources = ARRAY_SIZE(nand_resources),
-};
-
-void __init at91_add_device_nand(struct atmel_nand_data *data)
-{
- unsigned long csa;
-
- if (!data)
- return;
-
- csa = at91_sys_read(AT91_MATRIX_EBICSA);
- at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
-
- /* enable pin */
- if (gpio_is_valid(data->enable_pin))
- at91_set_gpio_output(data->enable_pin, 1);
-
- /* ready/busy pin */
- if (gpio_is_valid(data->rdy_pin))
- at91_set_gpio_input(data->rdy_pin, 1);
-
- /* card detect pin */
- if (gpio_is_valid(data->det_pin))
- at91_set_gpio_input(data->det_pin, 1);
-
- nand_data = *data;
- platform_device_register(&at91cap9_nand_device);
-}
-#else
-void __init at91_add_device_nand(struct atmel_nand_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * TWI (i2c)
- * -------------------------------------------------------------------- */
-
-/*
- * Prefer the GPIO code since the TWI controller isn't robust
- * (gets overruns and underruns under load) and can only issue
- * repeated STARTs in one scenario (the driver doesn't yet handle them).
- */
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
-
-static struct i2c_gpio_platform_data pdata = {
- .sda_pin = AT91_PIN_PB4,
- .sda_is_open_drain = 1,
- .scl_pin = AT91_PIN_PB5,
- .scl_is_open_drain = 1,
- .udelay = 2, /* ~100 kHz */
-};
-
-static struct platform_device at91cap9_twi_device = {
- .name = "i2c-gpio",
- .id = -1,
- .dev.platform_data = &pdata,
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
- at91_set_GPIO_periph(AT91_PIN_PB4, 1); /* TWD (SDA) */
- at91_set_multi_drive(AT91_PIN_PB4, 1);
-
- at91_set_GPIO_periph(AT91_PIN_PB5, 1); /* TWCK (SCL) */
- at91_set_multi_drive(AT91_PIN_PB5, 1);
-
- i2c_register_board_info(0, devices, nr_devices);
- platform_device_register(&at91cap9_twi_device);
-}
-
-#elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
-
-static struct resource twi_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_TWI,
- .end = AT91CAP9_BASE_TWI + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_TWI,
- .end = AT91CAP9_ID_TWI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91cap9_twi_device = {
- .name = "at91_i2c",
- .id = -1,
- .resource = twi_resources,
- .num_resources = ARRAY_SIZE(twi_resources),
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
- /* pins used for TWI interface */
- at91_set_B_periph(AT91_PIN_PB4, 0); /* TWD */
- at91_set_multi_drive(AT91_PIN_PB4, 1);
-
- at91_set_B_periph(AT91_PIN_PB5, 0); /* TWCK */
- at91_set_multi_drive(AT91_PIN_PB5, 1);
-
- i2c_register_board_info(0, devices, nr_devices);
- platform_device_register(&at91cap9_twi_device);
-}
-#else
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices) {}
-#endif
-
-/* --------------------------------------------------------------------
- * SPI
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-static struct resource spi0_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_SPI0,
- .end = AT91CAP9_BASE_SPI0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_SPI0,
- .end = AT91CAP9_ID_SPI0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91cap9_spi0_device = {
- .name = "atmel_spi",
- .id = 0,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = spi0_resources,
- .num_resources = ARRAY_SIZE(spi0_resources),
-};
-
-static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA5, AT91_PIN_PA3, AT91_PIN_PD0, AT91_PIN_PD1 };
-
-static struct resource spi1_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_SPI1,
- .end = AT91CAP9_BASE_SPI1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_SPI1,
- .end = AT91CAP9_ID_SPI1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91cap9_spi1_device = {
- .name = "atmel_spi",
- .id = 1,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = spi1_resources,
- .num_resources = ARRAY_SIZE(spi1_resources),
-};
-
-static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB15, AT91_PIN_PB16, AT91_PIN_PB17, AT91_PIN_PB18 };
-
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
-{
- int i;
- unsigned long cs_pin;
- short enable_spi0 = 0;
- short enable_spi1 = 0;
-
- /* Choose SPI chip-selects */
- for (i = 0; i < nr_devices; i++) {
- if (devices[i].controller_data)
- cs_pin = (unsigned long) devices[i].controller_data;
- else if (devices[i].bus_num == 0)
- cs_pin = spi0_standard_cs[devices[i].chip_select];
- else
- cs_pin = spi1_standard_cs[devices[i].chip_select];
-
- if (devices[i].bus_num == 0)
- enable_spi0 = 1;
- else
- enable_spi1 = 1;
-
- /* enable chip-select pin */
- at91_set_gpio_output(cs_pin, 1);
-
- /* pass chip-select pin to driver */
- devices[i].controller_data = (void *) cs_pin;
- }
-
- spi_register_board_info(devices, nr_devices);
-
- /* Configure SPI bus(es) */
- if (enable_spi0) {
- at91_set_B_periph(AT91_PIN_PA0, 0); /* SPI0_MISO */
- at91_set_B_periph(AT91_PIN_PA1, 0); /* SPI0_MOSI */
- at91_set_B_periph(AT91_PIN_PA2, 0); /* SPI0_SPCK */
-
- platform_device_register(&at91cap9_spi0_device);
- }
- if (enable_spi1) {
- at91_set_A_periph(AT91_PIN_PB12, 0); /* SPI1_MISO */
- at91_set_A_periph(AT91_PIN_PB13, 0); /* SPI1_MOSI */
- at91_set_A_periph(AT91_PIN_PB14, 0); /* SPI1_SPCK */
-
- platform_device_register(&at91cap9_spi1_device);
- }
-}
-#else
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * Timer/Counter block
- * -------------------------------------------------------------------- */
-
-#ifdef CONFIG_ATMEL_TCLIB
-
-static struct resource tcb_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_TCB0,
- .end = AT91CAP9_BASE_TCB0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_TCB,
- .end = AT91CAP9_ID_TCB,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91cap9_tcb_device = {
- .name = "atmel_tcb",
- .id = 0,
- .resource = tcb_resources,
- .num_resources = ARRAY_SIZE(tcb_resources),
-};
-
-static void __init at91_add_device_tc(void)
-{
- platform_device_register(&at91cap9_tcb_device);
-}
-#else
-static void __init at91_add_device_tc(void) { }
-#endif
-
-
-/* --------------------------------------------------------------------
- * RTT
- * -------------------------------------------------------------------- */
-
-static struct resource rtt_resources[] = {
- {
- .start = AT91CAP9_BASE_RTT,
- .end = AT91CAP9_BASE_RTT + SZ_16 - 1,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct platform_device at91cap9_rtt_device = {
- .name = "at91_rtt",
- .id = 0,
- .resource = rtt_resources,
- .num_resources = ARRAY_SIZE(rtt_resources),
-};
-
-static void __init at91_add_device_rtt(void)
-{
- platform_device_register(&at91cap9_rtt_device);
-}
-
-
-/* --------------------------------------------------------------------
- * Watchdog
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
-static struct resource wdt_resources[] = {
- {
- .start = AT91CAP9_BASE_WDT,
- .end = AT91CAP9_BASE_WDT + SZ_16 - 1,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct platform_device at91cap9_wdt_device = {
- .name = "at91_wdt",
- .id = -1,
- .resource = wdt_resources,
- .num_resources = ARRAY_SIZE(wdt_resources),
-};
-
-static void __init at91_add_device_watchdog(void)
-{
- platform_device_register(&at91cap9_wdt_device);
-}
-#else
-static void __init at91_add_device_watchdog(void) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * PWM
- * --------------------------------------------------------------------*/
-
-#if defined(CONFIG_ATMEL_PWM)
-static u32 pwm_mask;
-
-static struct resource pwm_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_PWMC,
- .end = AT91CAP9_BASE_PWMC + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_PWMC,
- .end = AT91CAP9_ID_PWMC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91cap9_pwm0_device = {
- .name = "atmel_pwm",
- .id = -1,
- .dev = {
- .platform_data = &pwm_mask,
- },
- .resource = pwm_resources,
- .num_resources = ARRAY_SIZE(pwm_resources),
-};
-
-void __init at91_add_device_pwm(u32 mask)
-{
- if (mask & (1 << AT91_PWM0))
- at91_set_A_periph(AT91_PIN_PB19, 1); /* enable PWM0 */
-
- if (mask & (1 << AT91_PWM1))
- at91_set_B_periph(AT91_PIN_PB8, 1); /* enable PWM1 */
-
- if (mask & (1 << AT91_PWM2))
- at91_set_B_periph(AT91_PIN_PC29, 1); /* enable PWM2 */
-
- if (mask & (1 << AT91_PWM3))
- at91_set_B_periph(AT91_PIN_PA11, 1); /* enable PWM3 */
-
- pwm_mask = mask;
-
- platform_device_register(&at91cap9_pwm0_device);
-}
-#else
-void __init at91_add_device_pwm(u32 mask) {}
-#endif
-
-
-
-/* --------------------------------------------------------------------
- * AC97
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
-static u64 ac97_dmamask = DMA_BIT_MASK(32);
-static struct ac97c_platform_data ac97_data;
-
-static struct resource ac97_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_AC97C,
- .end = AT91CAP9_BASE_AC97C + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_AC97C,
- .end = AT91CAP9_ID_AC97C,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91cap9_ac97_device = {
- .name = "atmel_ac97c",
- .id = 1,
- .dev = {
- .dma_mask = &ac97_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &ac97_data,
- },
- .resource = ac97_resources,
- .num_resources = ARRAY_SIZE(ac97_resources),
-};
-
-void __init at91_add_device_ac97(struct ac97c_platform_data *data)
-{
- if (!data)
- return;
-
- at91_set_A_periph(AT91_PIN_PA6, 0); /* AC97FS */
- at91_set_A_periph(AT91_PIN_PA7, 0); /* AC97CK */
- at91_set_A_periph(AT91_PIN_PA8, 0); /* AC97TX */
- at91_set_A_periph(AT91_PIN_PA9, 0); /* AC97RX */
-
- /* reset */
- if (gpio_is_valid(data->reset_pin))
- at91_set_gpio_output(data->reset_pin, 0);
-
- ac97_data = *data;
- platform_device_register(&at91cap9_ac97_device);
-}
-#else
-void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * LCD Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
-
-static struct resource lcdc_resources[] = {
- [0] = {
- .start = AT91CAP9_LCDC_BASE,
- .end = AT91CAP9_LCDC_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_LCDC,
- .end = AT91CAP9_ID_LCDC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91_lcdc_device = {
- .name = "atmel_lcdfb",
- .id = 0,
- .dev = {
- .dma_mask = &lcdc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &lcdc_data,
- },
- .resource = lcdc_resources,
- .num_resources = ARRAY_SIZE(lcdc_resources),
-};
-
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
-{
- if (!data)
- return;
-
- if (cpu_is_at91cap9_revB())
- irq_set_irq_type(AT91CAP9_ID_LCDC, IRQ_TYPE_LEVEL_HIGH);
-
- at91_set_A_periph(AT91_PIN_PC1, 0); /* LCDHSYNC */
- at91_set_A_periph(AT91_PIN_PC2, 0); /* LCDDOTCK */
- at91_set_A_periph(AT91_PIN_PC3, 0); /* LCDDEN */
- at91_set_B_periph(AT91_PIN_PB9, 0); /* LCDCC */
- at91_set_A_periph(AT91_PIN_PC6, 0); /* LCDD2 */
- at91_set_A_periph(AT91_PIN_PC7, 0); /* LCDD3 */
- at91_set_A_periph(AT91_PIN_PC8, 0); /* LCDD4 */
- at91_set_A_periph(AT91_PIN_PC9, 0); /* LCDD5 */
- at91_set_A_periph(AT91_PIN_PC10, 0); /* LCDD6 */
- at91_set_A_periph(AT91_PIN_PC11, 0); /* LCDD7 */
- at91_set_A_periph(AT91_PIN_PC14, 0); /* LCDD10 */
- at91_set_A_periph(AT91_PIN_PC15, 0); /* LCDD11 */
- at91_set_A_periph(AT91_PIN_PC16, 0); /* LCDD12 */
- at91_set_A_periph(AT91_PIN_PC17, 0); /* LCDD13 */
- at91_set_A_periph(AT91_PIN_PC18, 0); /* LCDD14 */
- at91_set_A_periph(AT91_PIN_PC19, 0); /* LCDD15 */
- at91_set_A_periph(AT91_PIN_PC22, 0); /* LCDD18 */
- at91_set_A_periph(AT91_PIN_PC23, 0); /* LCDD19 */
- at91_set_A_periph(AT91_PIN_PC24, 0); /* LCDD20 */
- at91_set_A_periph(AT91_PIN_PC25, 0); /* LCDD21 */
- at91_set_A_periph(AT91_PIN_PC26, 0); /* LCDD22 */
- at91_set_A_periph(AT91_PIN_PC27, 0); /* LCDD23 */
-
- lcdc_data = *data;
- platform_device_register(&at91_lcdc_device);
-}
-#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * SSC -- Synchronous Serial Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
-static u64 ssc0_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc0_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_SSC0,
- .end = AT91CAP9_BASE_SSC0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_SSC0,
- .end = AT91CAP9_ID_SSC0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91cap9_ssc0_device = {
- .name = "ssc",
- .id = 0,
- .dev = {
- .dma_mask = &ssc0_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = ssc0_resources,
- .num_resources = ARRAY_SIZE(ssc0_resources),
-};
-
-static inline void configure_ssc0_pins(unsigned pins)
-{
- if (pins & ATMEL_SSC_TF)
- at91_set_A_periph(AT91_PIN_PB0, 1);
- if (pins & ATMEL_SSC_TK)
- at91_set_A_periph(AT91_PIN_PB1, 1);
- if (pins & ATMEL_SSC_TD)
- at91_set_A_periph(AT91_PIN_PB2, 1);
- if (pins & ATMEL_SSC_RD)
- at91_set_A_periph(AT91_PIN_PB3, 1);
- if (pins & ATMEL_SSC_RK)
- at91_set_A_periph(AT91_PIN_PB4, 1);
- if (pins & ATMEL_SSC_RF)
- at91_set_A_periph(AT91_PIN_PB5, 1);
-}
-
-static u64 ssc1_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc1_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_SSC1,
- .end = AT91CAP9_BASE_SSC1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_SSC1,
- .end = AT91CAP9_ID_SSC1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91cap9_ssc1_device = {
- .name = "ssc",
- .id = 1,
- .dev = {
- .dma_mask = &ssc1_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = ssc1_resources,
- .num_resources = ARRAY_SIZE(ssc1_resources),
-};
-
-static inline void configure_ssc1_pins(unsigned pins)
-{
- if (pins & ATMEL_SSC_TF)
- at91_set_A_periph(AT91_PIN_PB6, 1);
- if (pins & ATMEL_SSC_TK)
- at91_set_A_periph(AT91_PIN_PB7, 1);
- if (pins & ATMEL_SSC_TD)
- at91_set_A_periph(AT91_PIN_PB8, 1);
- if (pins & ATMEL_SSC_RD)
- at91_set_A_periph(AT91_PIN_PB9, 1);
- if (pins & ATMEL_SSC_RK)
- at91_set_A_periph(AT91_PIN_PB10, 1);
- if (pins & ATMEL_SSC_RF)
- at91_set_A_periph(AT91_PIN_PB11, 1);
-}
-
-/*
- * SSC controllers are accessed through library code, instead of any
- * kind of all-singing/all-dancing driver. For example one could be
- * used by a particular I2S audio codec's driver, while another one
- * on the same system might be used by a custom data capture driver.
- */
-void __init at91_add_device_ssc(unsigned id, unsigned pins)
-{
- struct platform_device *pdev;
-
- /*
- * NOTE: caller is responsible for passing information matching
- * "pins" to whatever will be using each particular controller.
- */
- switch (id) {
- case AT91CAP9_ID_SSC0:
- pdev = &at91cap9_ssc0_device;
- configure_ssc0_pins(pins);
- break;
- case AT91CAP9_ID_SSC1:
- pdev = &at91cap9_ssc1_device;
- configure_ssc1_pins(pins);
- break;
- default:
- return;
- }
-
- platform_device_register(pdev);
-}
-
-#else
-void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * UART
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SERIAL_ATMEL)
-static struct resource dbgu_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_DBGU,
- .end = AT91CAP9_BASE_DBGU + SZ_512 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91_ID_SYS,
- .end = AT91_ID_SYS,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data dbgu_data = {
- .use_dma_tx = 0,
- .use_dma_rx = 0, /* DBGU not capable of receive DMA */
-};
-
-static u64 dbgu_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91cap9_dbgu_device = {
- .name = "atmel_usart",
- .id = 0,
- .dev = {
- .dma_mask = &dbgu_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &dbgu_data,
- },
- .resource = dbgu_resources,
- .num_resources = ARRAY_SIZE(dbgu_resources),
-};
-
-static inline void configure_dbgu_pins(void)
-{
- at91_set_A_periph(AT91_PIN_PC30, 0); /* DRXD */
- at91_set_A_periph(AT91_PIN_PC31, 1); /* DTXD */
-}
-
-static struct resource uart0_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_US0,
- .end = AT91CAP9_BASE_US0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_US0,
- .end = AT91CAP9_ID_US0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart0_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static u64 uart0_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91cap9_uart0_device = {
- .name = "atmel_usart",
- .id = 1,
- .dev = {
- .dma_mask = &uart0_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart0_data,
- },
- .resource = uart0_resources,
- .num_resources = ARRAY_SIZE(uart0_resources),
-};
-
-static inline void configure_usart0_pins(unsigned pins)
-{
- at91_set_A_periph(AT91_PIN_PA22, 1); /* TXD0 */
- at91_set_A_periph(AT91_PIN_PA23, 0); /* RXD0 */
-
- if (pins & ATMEL_UART_RTS)
- at91_set_A_periph(AT91_PIN_PA24, 0); /* RTS0 */
- if (pins & ATMEL_UART_CTS)
- at91_set_A_periph(AT91_PIN_PA25, 0); /* CTS0 */
-}
-
-static struct resource uart1_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_US1,
- .end = AT91CAP9_BASE_US1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_US1,
- .end = AT91CAP9_ID_US1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart1_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static u64 uart1_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91cap9_uart1_device = {
- .name = "atmel_usart",
- .id = 2,
- .dev = {
- .dma_mask = &uart1_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart1_data,
- },
- .resource = uart1_resources,
- .num_resources = ARRAY_SIZE(uart1_resources),
-};
-
-static inline void configure_usart1_pins(unsigned pins)
-{
- at91_set_A_periph(AT91_PIN_PD0, 1); /* TXD1 */
- at91_set_A_periph(AT91_PIN_PD1, 0); /* RXD1 */
-
- if (pins & ATMEL_UART_RTS)
- at91_set_B_periph(AT91_PIN_PD7, 0); /* RTS1 */
- if (pins & ATMEL_UART_CTS)
- at91_set_B_periph(AT91_PIN_PD8, 0); /* CTS1 */
-}
-
-static struct resource uart2_resources[] = {
- [0] = {
- .start = AT91CAP9_BASE_US2,
- .end = AT91CAP9_BASE_US2 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91CAP9_ID_US2,
- .end = AT91CAP9_ID_US2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart2_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static u64 uart2_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91cap9_uart2_device = {
- .name = "atmel_usart",
- .id = 3,
- .dev = {
- .dma_mask = &uart2_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart2_data,
- },
- .resource = uart2_resources,
- .num_resources = ARRAY_SIZE(uart2_resources),
-};
-
-static inline void configure_usart2_pins(unsigned pins)
-{
- at91_set_A_periph(AT91_PIN_PD2, 1); /* TXD2 */
- at91_set_A_periph(AT91_PIN_PD3, 0); /* RXD2 */
-
- if (pins & ATMEL_UART_RTS)
- at91_set_B_periph(AT91_PIN_PD5, 0); /* RTS2 */
- if (pins & ATMEL_UART_CTS)
- at91_set_B_periph(AT91_PIN_PD6, 0); /* CTS2 */
-}
-
-static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
-struct platform_device *atmel_default_console_device; /* the serial console device */
-
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
-{
- struct platform_device *pdev;
- struct atmel_uart_data *pdata;
-
- switch (id) {
- case 0: /* DBGU */
- pdev = &at91cap9_dbgu_device;
- configure_dbgu_pins();
- break;
- case AT91CAP9_ID_US0:
- pdev = &at91cap9_uart0_device;
- configure_usart0_pins(pins);
- break;
- case AT91CAP9_ID_US1:
- pdev = &at91cap9_uart1_device;
- configure_usart1_pins(pins);
- break;
- case AT91CAP9_ID_US2:
- pdev = &at91cap9_uart2_device;
- configure_usart2_pins(pins);
- break;
- default:
- return;
- }
- pdata = pdev->dev.platform_data;
- pdata->num = portnr; /* update to mapped ID */
-
- if (portnr < ATMEL_MAX_UART)
- at91_uarts[portnr] = pdev;
-}
-
-void __init at91_set_serial_console(unsigned portnr)
-{
- if (portnr < ATMEL_MAX_UART) {
- atmel_default_console_device = at91_uarts[portnr];
- at91cap9_set_console_clock(at91_uarts[portnr]->id);
- }
-}
-
-void __init at91_add_device_serial(void)
-{
- int i;
-
- for (i = 0; i < ATMEL_MAX_UART; i++) {
- if (at91_uarts[i])
- platform_device_register(at91_uarts[i]);
- }
-
- if (!atmel_default_console_device)
- printk(KERN_INFO "AT91: No default serial console defined.\n");
-}
-#else
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
-void __init at91_add_device_serial(void) {}
-#endif
-
-
-/* -------------------------------------------------------------------- */
-/*
- * These devices are always present and don't need any board-specific
- * setup.
- */
-static int __init at91_add_standard_devices(void)
-{
- at91_add_device_rtt();
- at91_add_device_watchdog();
- at91_add_device_tc();
- return 0;
-}
-
-arch_initcall(at91_add_standard_devices);
diff --git a/arch/arm/mach-at91/board-cap9adk.c b/arch/arm/mach-at91/board-cap9adk.c
deleted file mode 100644
index ac3de4f..0000000
--- a/arch/arm/mach-at91/board-cap9adk.c
+++ /dev/null
@@ -1,396 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-cap9adk.c
- *
- * Copyright (C) 2007 Stelian Pop <stelian.pop at leadtechdesign.com>
- * Copyright (C) 2007 Lead Tech Design <www.leadtechdesign.com>
- * Copyright (C) 2005 SAN People
- * Copyright (C) 2007 Atmel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/fb.h>
-#include <linux/mtd/physmap.h>
-
-#include <video/atmel_lcdc.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <mach/board.h>
-#include <mach/at91cap9_matrix.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/system_rev.h>
-
-#include "sam9_smc.h"
-#include "generic.h"
-
-
-static void __init cap9adk_init_early(void)
-{
- /* Initialize processor: 12 MHz crystal */
- at91_initialize(12000000);
-
- /* Setup the LEDs: USER1 and USER2 LED for cpu/timer... */
- at91_init_leds(AT91_PIN_PA10, AT91_PIN_PA11);
- /* ... POWER LED always on */
- at91_set_gpio_output(AT91_PIN_PC29, 1);
-
- /* Setup the serial ports and console */
- at91_register_uart(0, 0, 0); /* DBGU = ttyS0 */
- at91_set_serial_console(0);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata cap9adk_usbh_data = {
- .ports = 2,
- .vbus_pin = {-EINVAL, -EINVAL},
- .overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB HS Device port
- */
-static struct usba_platform_data __initdata cap9adk_usba_udc_data = {
- .vbus_pin = AT91_PIN_PB31,
-};
-
-/*
- * ADS7846 Touchscreen
- */
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-static int ads7843_pendown_state(void)
-{
- return !at91_get_gpio_value(AT91_PIN_PC4); /* Touchscreen PENIRQ */
-}
-
-static struct ads7846_platform_data ads_info = {
- .model = 7843,
- .x_min = 150,
- .x_max = 3830,
- .y_min = 190,
- .y_max = 3830,
- .vref_delay_usecs = 100,
- .x_plate_ohms = 450,
- .y_plate_ohms = 250,
- .pressure_max = 15000,
- .debounce_max = 1,
- .debounce_rep = 0,
- .debounce_tol = (~0),
- .get_pendown_state = ads7843_pendown_state,
-};
-
-static void __init cap9adk_add_device_ts(void)
-{
- at91_set_gpio_input(AT91_PIN_PC4, 1); /* Touchscreen PENIRQ */
- at91_set_gpio_input(AT91_PIN_PC5, 1); /* Touchscreen BUSY */
-}
-#else
-static void __init cap9adk_add_device_ts(void) {}
-#endif
-
-
-/*
- * SPI devices.
- */
-static struct spi_board_info cap9adk_spi_devices[] = {
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
- { /* DataFlash card */
- .modalias = "mtd_dataflash",
- .chip_select = 0,
- .max_speed_hz = 15 * 1000 * 1000,
- .bus_num = 0,
- },
-#endif
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
- {
- .modalias = "ads7846",
- .chip_select = 3, /* can be 2 or 3, depending on J2 jumper */
- .max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */
- .bus_num = 0,
- .platform_data = &ads_info,
- .irq = AT91_PIN_PC4,
- },
-#endif
-};
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct at91_mmc_data __initdata cap9adk_mmc_data = {
- .wire4 = 1,
- .det_pin = -EINVAL,
- .wp_pin = -EINVAL,
- .vcc_pin = -EINVAL,
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata cap9adk_macb_data = {
- .phy_irq_pin = -EINVAL,
- .is_rmii = 1,
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata cap9adk_nand_partitions[] = {
- {
- .name = "NAND partition",
- .offset = 0,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct atmel_nand_data __initdata cap9adk_nand_data = {
- .ale = 21,
- .cle = 22,
- .det_pin = -EINVAL,
- .rdy_pin = -EINVAL,
- .enable_pin = AT91_PIN_PD15,
- .parts = cap9adk_nand_partitions,
- .num_parts = ARRAY_SIZE(cap9adk_nand_partitions),
-};
-
-static struct sam9_smc_config __initdata cap9adk_nand_smc_config = {
- .ncs_read_setup = 1,
- .nrd_setup = 2,
- .ncs_write_setup = 1,
- .nwe_setup = 2,
-
- .ncs_read_pulse = 6,
- .nrd_pulse = 4,
- .ncs_write_pulse = 6,
- .nwe_pulse = 4,
-
- .read_cycle = 8,
- .write_cycle = 8,
-
- .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
- .tdf_cycles = 1,
-};
-
-static void __init cap9adk_add_device_nand(void)
-{
- unsigned long csa;
-
- csa = at91_sys_read(AT91_MATRIX_EBICSA);
- at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V);
-
- cap9adk_nand_data.bus_width_16 = board_have_nand_16bit();
- /* setup bus-width (8 or 16) */
- if (cap9adk_nand_data.bus_width_16)
- cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_16;
- else
- cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
- /* configure chip-select 3 (NAND) */
- sam9_smc_configure(0, 3, &cap9adk_nand_smc_config);
-
- at91_add_device_nand(&cap9adk_nand_data);
-}
-
-
-/*
- * NOR flash
- */
-static struct mtd_partition cap9adk_nor_partitions[] = {
- {
- .name = "NOR partition",
- .offset = 0,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct physmap_flash_data cap9adk_nor_data = {
- .width = 2,
- .parts = cap9adk_nor_partitions,
- .nr_parts = ARRAY_SIZE(cap9adk_nor_partitions),
-};
-
-#define NOR_BASE AT91_CHIPSELECT_0
-#define NOR_SIZE SZ_8M
-
-static struct resource nor_flash_resources[] = {
- {
- .start = NOR_BASE,
- .end = NOR_BASE + NOR_SIZE - 1,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct platform_device cap9adk_nor_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &cap9adk_nor_data,
- },
- .resource = nor_flash_resources,
- .num_resources = ARRAY_SIZE(nor_flash_resources),
-};
-
-static struct sam9_smc_config __initdata cap9adk_nor_smc_config = {
- .ncs_read_setup = 2,
- .nrd_setup = 4,
- .ncs_write_setup = 2,
- .nwe_setup = 4,
-
- .ncs_read_pulse = 10,
- .nrd_pulse = 8,
- .ncs_write_pulse = 10,
- .nwe_pulse = 8,
-
- .read_cycle = 16,
- .write_cycle = 16,
-
- .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16,
- .tdf_cycles = 1,
-};
-
-static __init void cap9adk_add_device_nor(void)
-{
- unsigned long csa;
-
- csa = at91_sys_read(AT91_MATRIX_EBICSA);
- at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V);
-
- /* configure chip-select 0 (NOR) */
- sam9_smc_configure(0, 0, &cap9adk_nor_smc_config);
-
- platform_device_register(&cap9adk_nor_flash);
-}
-
-
-/*
- * LCD Controller
- */
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static struct fb_videomode at91_tft_vga_modes[] = {
- {
- .name = "TX09D50VM1CCA @ 60",
- .refresh = 60,
- .xres = 240, .yres = 320,
- .pixclock = KHZ2PICOS(4965),
-
- .left_margin = 1, .right_margin = 33,
- .upper_margin = 1, .lower_margin = 0,
- .hsync_len = 5, .vsync_len = 1,
-
- .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
- .vmode = FB_VMODE_NONINTERLACED,
- },
-};
-
-static struct fb_monspecs at91fb_default_monspecs = {
- .manufacturer = "HIT",
- .monitor = "TX09D70VM1CCA",
-
- .modedb = at91_tft_vga_modes,
- .modedb_len = ARRAY_SIZE(at91_tft_vga_modes),
- .hfmin = 15000,
- .hfmax = 64000,
- .vfmin = 50,
- .vfmax = 150,
-};
-
-#define AT91CAP9_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
- | ATMEL_LCDC_DISTYPE_TFT \
- | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-
-static void at91_lcdc_power_control(int on)
-{
- if (on)
- at91_set_gpio_value(AT91_PIN_PC0, 0); /* power up */
- else
- at91_set_gpio_value(AT91_PIN_PC0, 1); /* power down */
-}
-
-/* Driver datas */
-static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data = {
- .default_bpp = 16,
- .default_dmacon = ATMEL_LCDC_DMAEN,
- .default_lcdcon2 = AT91CAP9_DEFAULT_LCDCON2,
- .default_monspecs = &at91fb_default_monspecs,
- .atmel_lcdfb_power_control = at91_lcdc_power_control,
- .guard_time = 1,
-};
-
-#else
-static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data;
-#endif
-
-
-/*
- * AC97
- */
-static struct ac97c_platform_data cap9adk_ac97_data = {
- .reset_pin = -EINVAL,
-};
-
-
-static void __init cap9adk_board_init(void)
-{
- /* Serial */
- at91_add_device_serial();
- /* USB Host */
- at91_add_device_usbh(&cap9adk_usbh_data);
- /* USB HS */
- at91_add_device_usba(&cap9adk_usba_udc_data);
- /* SPI */
- at91_add_device_spi(cap9adk_spi_devices, ARRAY_SIZE(cap9adk_spi_devices));
- /* Touchscreen */
- cap9adk_add_device_ts();
- /* MMC */
- at91_add_device_mmc(1, &cap9adk_mmc_data);
- /* Ethernet */
- at91_add_device_eth(&cap9adk_macb_data);
- /* NAND */
- cap9adk_add_device_nand();
- /* NOR Flash */
- cap9adk_add_device_nor();
- /* I2C */
- at91_add_device_i2c(NULL, 0);
- /* LCD Controller */
- at91_add_device_lcdc(&cap9adk_lcdc_data);
- /* AC97 */
- at91_add_device_ac97(&cap9adk_ac97_data);
-}
-
-MACHINE_START(AT91CAP9ADK, "Atmel AT91CAP9A-DK")
- /* Maintainer: Stelian Pop <stelian.pop at leadtechdesign.com> */
- .timer = &at91sam926x_timer,
- .map_io = at91_map_io,
- .init_early = cap9adk_init_early,
- .init_irq = at91_init_irq_default,
- .init_machine = cap9adk_board_init,
-MACHINE_END
diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c
index ca76b5a..a5291e0 100644
--- a/arch/arm/mach-at91/clock.c
+++ b/arch/arm/mach-at91/clock.c
@@ -47,8 +47,7 @@
/*
* Chips have some kind of clocks : group them by functionality
*/
-#define cpu_has_utmi() ( cpu_is_at91cap9() \
- || cpu_is_at91sam9rl() \
+#define cpu_has_utmi() ( cpu_is_at91sam9rl() \
|| cpu_is_at91sam9g45() \
|| cpu_is_at91sam9x5())
@@ -637,8 +636,6 @@ static void __init at91_pllb_usbfs_clock_init(unsigned long main_clock)
cpu_is_at91sam9g10()) {
uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
udpck.pmc_mask = AT91SAM926x_PMC_UDP;
- } else if (cpu_is_at91cap9()) {
- uhpck.pmc_mask = AT91CAP9_PMC_UHP;
}
at91_sys_write(AT91_CKGR_PLLBR, 0);
diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h
index 07f5505..78cd605 100644
--- a/arch/arm/mach-at91/generic.h
+++ b/arch/arm/mach-at91/generic.h
@@ -46,7 +46,6 @@ extern void __init at91sam9261_set_console_clock(int id);
extern void __init at91sam9263_set_console_clock(int id);
extern void __init at91sam9rl_set_console_clock(int id);
extern void __init at91sam9g45_set_console_clock(int id);
-extern void __init at91cap9_set_console_clock(int id);
#ifdef CONFIG_AT91_PMC_UNIT
extern int __init at91_clock_init(unsigned long main_clock);
#else
diff --git a/arch/arm/mach-at91/include/mach/at91_pmc.h b/arch/arm/mach-at91/include/mach/at91_pmc.h
index 1782178..4675789 100644
--- a/arch/arm/mach-at91/include/mach/at91_pmc.h
+++ b/arch/arm/mach-at91/include/mach/at91_pmc.h
@@ -23,10 +23,8 @@
#define AT91_PMC_PCK (1 << 0) /* Processor Clock */
#define AT91RM9200_PMC_UDP (1 << 1) /* USB Devcice Port Clock [AT91RM9200 only] */
#define AT91RM9200_PMC_MCKUDP (1 << 2) /* USB Device Port Master Clock Automatic Disable on Suspend [AT91RM9200 only] */
-#define AT91CAP9_PMC_DDR (1 << 2) /* DDR Clock [CAP9 revC & some SAM9 only] */
#define AT91RM9200_PMC_UHP (1 << 4) /* USB Host Port Clock [AT91RM9200 only] */
#define AT91SAM926x_PMC_UHP (1 << 6) /* USB Host Port Clock [AT91SAM926x only] */
-#define AT91CAP9_PMC_UHP (1 << 6) /* USB Host Port Clock [AT91CAP9 only] */
#define AT91SAM926x_PMC_UDP (1 << 7) /* USB Devcice Port Clock [AT91SAM926x only] */
#define AT91_PMC_PCK0 (1 << 8) /* Programmable Clock 0 */
#define AT91_PMC_PCK1 (1 << 9) /* Programmable Clock 1 */
@@ -40,7 +38,7 @@
#define AT91_PMC_PCDR (AT91_PMC + 0x14) /* Peripheral Clock Disable Register */
#define AT91_PMC_PCSR (AT91_PMC + 0x18) /* Peripheral Clock Status Register */
-#define AT91_CKGR_UCKR (AT91_PMC + 0x1C) /* UTMI Clock Register [some SAM9, CAP9] */
+#define AT91_CKGR_UCKR (AT91_PMC + 0x1C) /* UTMI Clock Register [some SAM9] */
#define AT91_PMC_UPLLEN (1 << 16) /* UTMI PLL Enable */
#define AT91_PMC_UPLLCOUNT (0xf << 20) /* UTMI PLL Start-up Time */
#define AT91_PMC_BIASEN (1 << 24) /* UTMI BIAS Enable */
@@ -48,7 +46,7 @@
#define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register [not on SAM9RL] */
#define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */
-#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [SAM9x, CAP9] */
+#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [SAM9x] */
#define AT91_PMC_MOSCRCEN (1 << 3) /* Main On-Chip RC Oscillator Enable [some SAM9] */
#define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */
#define AT91_PMC_KEY (0x37 << 16) /* MOR Writing Key */
@@ -101,7 +99,7 @@
#define AT91RM9200_PMC_MDIV_2 (1 << 8)
#define AT91RM9200_PMC_MDIV_3 (2 << 8)
#define AT91RM9200_PMC_MDIV_4 (3 << 8)
-#define AT91SAM9_PMC_MDIV_1 (0 << 8) /* [SAM9,CAP9 only] */
+#define AT91SAM9_PMC_MDIV_1 (0 << 8) /* [SAM9 only] */
#define AT91SAM9_PMC_MDIV_2 (1 << 8)
#define AT91SAM9_PMC_MDIV_4 (2 << 8)
#define AT91SAM9_PMC_MDIV_6 (3 << 8) /* [some SAM9 only] */
@@ -126,7 +124,7 @@
#define AT91_PMC_PCKR(n) (AT91_PMC + 0x40 + ((n) * 4)) /* Programmable Clock 0-N Registers */
#define AT91_PMC_ALT_PCKR_CSS (0x7 << 0) /* Programmable Clock Source Selection [alternate length] */
-#define AT91_PMC_CSS_MASTER (4 << 0) /* [some SAM9 only] */
+#define AT91_PMC_CSS_MASTER (4 << 0) /* [some SAM9] */
#define AT91_PMC_CSSMCK (0x1 << 8) /* CSS or Master Clock Selection */
#define AT91_PMC_CSSMCK_CSS (0 << 8)
#define AT91_PMC_CSSMCK_MCK (1 << 8)
@@ -138,8 +136,7 @@
#define AT91_PMC_LOCKA (1 << 1) /* PLLA Lock */
#define AT91_PMC_LOCKB (1 << 2) /* PLLB Lock */
#define AT91_PMC_MCKRDY (1 << 3) /* Master Clock */
-#define AT91_PMC_LOCKU (1 << 6) /* UPLL Lock [some SAM9, AT91CAP9 only] */
-#define AT91_PMC_OSCSEL (1 << 7) /* Slow Clock Oscillator [AT91CAP9 revC only] */
+#define AT91_PMC_LOCKU (1 << 6) /* UPLL Lock [some SAM9] */
#define AT91_PMC_PCK0RDY (1 << 8) /* Programmable Clock 0 */
#define AT91_PMC_PCK1RDY (1 << 9) /* Programmable Clock 1 */
#define AT91_PMC_PCK2RDY (1 << 10) /* Programmable Clock 2 */
@@ -149,7 +146,7 @@
#define AT91_PMC_CFDEV (1 << 18) /* Clock Failure Detector Event [some SAM9] */
#define AT91_PMC_IMR (AT91_PMC + 0x6c) /* Interrupt Mask Register */
-#define AT91_PMC_PROT (AT91_PMC + 0xe4) /* Write Protect Mode Register [some SAM9, AT91CAP9 revC only] */
+#define AT91_PMC_PROT (AT91_PMC + 0xe4) /* Write Protect Mode Register [some SAM9] */
#define AT91_PMC_WPEN (0x1 << 0) /* Write Protect Enable */
#define AT91_PMC_WPKEY (0xffffff << 8) /* Write Protect Key */
#define AT91_PMC_PROTKEY (0x504d43 << 8) /* Activation Code */
@@ -158,7 +155,6 @@
#define AT91_PMC_WPVS (0x1 << 0) /* Write Protect Violation Status */
#define AT91_PMC_WPVSRC (0xffff << 8) /* Write Protect Violation Source */
-#define AT91_PMC_VER (AT91_PMC + 0xfc) /* PMC Module Version [AT91CAP9 only] */
#define AT91_PMC_PCR (AT91_PMC + 0x10c) /* Peripheral Control Register [some SAM9] */
#define AT91_PMC_PCR_PID (0x3f << 0) /* Peripheral ID */
diff --git a/arch/arm/mach-at91/include/mach/at91cap9.h b/arch/arm/mach-at91/include/mach/at91cap9.h
deleted file mode 100644
index 61d9529..0000000
--- a/arch/arm/mach-at91/include/mach/at91cap9.h
+++ /dev/null
@@ -1,122 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91cap9.h
- *
- * Copyright (C) 2007 Stelian Pop <stelian.pop at leadtechdesign.com>
- * Copyright (C) 2007 Lead Tech Design <www.leadtechdesign.com>
- * Copyright (C) 2007 Atmel Corporation.
- *
- * Common definitions.
- * Based on AT91CAP9 datasheet revision B (Preliminary).
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91CAP9_H
-#define AT91CAP9_H
-
-/*
- * Peripheral identifiers/interrupts.
- */
-#define AT91CAP9_ID_PIOABCD 2 /* Parallel IO Controller A, B, C and D */
-#define AT91CAP9_ID_MPB0 3 /* MP Block Peripheral 0 */
-#define AT91CAP9_ID_MPB1 4 /* MP Block Peripheral 1 */
-#define AT91CAP9_ID_MPB2 5 /* MP Block Peripheral 2 */
-#define AT91CAP9_ID_MPB3 6 /* MP Block Peripheral 3 */
-#define AT91CAP9_ID_MPB4 7 /* MP Block Peripheral 4 */
-#define AT91CAP9_ID_US0 8 /* USART 0 */
-#define AT91CAP9_ID_US1 9 /* USART 1 */
-#define AT91CAP9_ID_US2 10 /* USART 2 */
-#define AT91CAP9_ID_MCI0 11 /* Multimedia Card Interface 0 */
-#define AT91CAP9_ID_MCI1 12 /* Multimedia Card Interface 1 */
-#define AT91CAP9_ID_CAN 13 /* CAN */
-#define AT91CAP9_ID_TWI 14 /* Two-Wire Interface */
-#define AT91CAP9_ID_SPI0 15 /* Serial Peripheral Interface 0 */
-#define AT91CAP9_ID_SPI1 16 /* Serial Peripheral Interface 0 */
-#define AT91CAP9_ID_SSC0 17 /* Serial Synchronous Controller 0 */
-#define AT91CAP9_ID_SSC1 18 /* Serial Synchronous Controller 1 */
-#define AT91CAP9_ID_AC97C 19 /* AC97 Controller */
-#define AT91CAP9_ID_TCB 20 /* Timer Counter 0, 1 and 2 */
-#define AT91CAP9_ID_PWMC 21 /* Pulse Width Modulation Controller */
-#define AT91CAP9_ID_EMAC 22 /* Ethernet */
-#define AT91CAP9_ID_AESTDES 23 /* Advanced Encryption Standard, Triple DES */
-#define AT91CAP9_ID_ADC 24 /* Analog-to-Digital Converter */
-#define AT91CAP9_ID_ISI 25 /* Image Sensor Interface */
-#define AT91CAP9_ID_LCDC 26 /* LCD Controller */
-#define AT91CAP9_ID_DMA 27 /* DMA Controller */
-#define AT91CAP9_ID_UDPHS 28 /* USB High Speed Device Port */
-#define AT91CAP9_ID_UHP 29 /* USB Host Port */
-#define AT91CAP9_ID_IRQ0 30 /* Advanced Interrupt Controller (IRQ0) */
-#define AT91CAP9_ID_IRQ1 31 /* Advanced Interrupt Controller (IRQ1) */
-
-/*
- * User Peripheral physical base addresses.
- */
-#define AT91CAP9_BASE_UDPHS 0xfff78000
-#define AT91CAP9_BASE_TCB0 0xfff7c000
-#define AT91CAP9_BASE_TC0 0xfff7c000
-#define AT91CAP9_BASE_TC1 0xfff7c040
-#define AT91CAP9_BASE_TC2 0xfff7c080
-#define AT91CAP9_BASE_MCI0 0xfff80000
-#define AT91CAP9_BASE_MCI1 0xfff84000
-#define AT91CAP9_BASE_TWI 0xfff88000
-#define AT91CAP9_BASE_US0 0xfff8c000
-#define AT91CAP9_BASE_US1 0xfff90000
-#define AT91CAP9_BASE_US2 0xfff94000
-#define AT91CAP9_BASE_SSC0 0xfff98000
-#define AT91CAP9_BASE_SSC1 0xfff9c000
-#define AT91CAP9_BASE_AC97C 0xfffa0000
-#define AT91CAP9_BASE_SPI0 0xfffa4000
-#define AT91CAP9_BASE_SPI1 0xfffa8000
-#define AT91CAP9_BASE_CAN 0xfffac000
-#define AT91CAP9_BASE_PWMC 0xfffb8000
-#define AT91CAP9_BASE_EMAC 0xfffbc000
-#define AT91CAP9_BASE_ADC 0xfffc0000
-#define AT91CAP9_BASE_ISI 0xfffc4000
-
-/*
- * System Peripherals (offset from AT91_BASE_SYS)
- */
-#define AT91_BCRAMC (0xffffe400 - AT91_BASE_SYS)
-#define AT91_DDRSDRC0 (0xffffe600 - AT91_BASE_SYS)
-#define AT91_MATRIX (0xffffea00 - AT91_BASE_SYS)
-#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
-#define AT91_GPBR (cpu_is_at91cap9_revB() ? \
- (0xfffffd50 - AT91_BASE_SYS) : \
- (0xfffffd60 - AT91_BASE_SYS))
-
-#define AT91CAP9_BASE_ECC 0xffffe200
-#define AT91CAP9_BASE_DMA 0xffffec00
-#define AT91CAP9_BASE_SMC 0xffffe800
-#define AT91CAP9_BASE_DBGU AT91_BASE_DBGU1
-#define AT91CAP9_BASE_PIOA 0xfffff200
-#define AT91CAP9_BASE_PIOB 0xfffff400
-#define AT91CAP9_BASE_PIOC 0xfffff600
-#define AT91CAP9_BASE_PIOD 0xfffff800
-#define AT91CAP9_BASE_RSTC 0xfffffd00
-#define AT91CAP9_BASE_SHDWC 0xfffffd10
-#define AT91CAP9_BASE_RTT 0xfffffd20
-#define AT91CAP9_BASE_PIT 0xfffffd30
-#define AT91CAP9_BASE_WDT 0xfffffd40
-
-#define AT91_USART0 AT91CAP9_BASE_US0
-#define AT91_USART1 AT91CAP9_BASE_US1
-#define AT91_USART2 AT91CAP9_BASE_US2
-
-
-/*
- * Internal Memory.
- */
-#define AT91CAP9_SRAM_BASE 0x00100000 /* Internal SRAM base address */
-#define AT91CAP9_SRAM_SIZE (32 * SZ_1K) /* Internal SRAM size (32Kb) */
-
-#define AT91CAP9_ROM_BASE 0x00400000 /* Internal ROM base address */
-#define AT91CAP9_ROM_SIZE (32 * SZ_1K) /* Internal ROM size (32Kb) */
-
-#define AT91CAP9_LCDC_BASE 0x00500000 /* LCD Controller */
-#define AT91CAP9_UDPHS_FIFO 0x00600000 /* USB High Speed Device Port */
-#define AT91CAP9_UHP_BASE 0x00700000 /* USB Host controller */
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91cap9_matrix.h b/arch/arm/mach-at91/include/mach/at91cap9_matrix.h
deleted file mode 100644
index 4b9d4af..0000000
--- a/arch/arm/mach-at91/include/mach/at91cap9_matrix.h
+++ /dev/null
@@ -1,137 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91cap9_matrix.h
- *
- * Copyright (C) 2007 Stelian Pop <stelian.pop at leadtechdesign.com>
- * Copyright (C) 2007 Lead Tech Design <www.leadtechdesign.com>
- * Copyright (C) 2006 Atmel Corporation.
- *
- * Memory Controllers (MATRIX, EBI) - System peripherals registers.
- * Based on AT91CAP9 datasheet revision B (Preliminary).
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91CAP9_MATRIX_H
-#define AT91CAP9_MATRIX_H
-
-#define AT91_MATRIX_MCFG0 (AT91_MATRIX + 0x00) /* Master Configuration Register 0 */
-#define AT91_MATRIX_MCFG1 (AT91_MATRIX + 0x04) /* Master Configuration Register 1 */
-#define AT91_MATRIX_MCFG2 (AT91_MATRIX + 0x08) /* Master Configuration Register 2 */
-#define AT91_MATRIX_MCFG3 (AT91_MATRIX + 0x0C) /* Master Configuration Register 3 */
-#define AT91_MATRIX_MCFG4 (AT91_MATRIX + 0x10) /* Master Configuration Register 4 */
-#define AT91_MATRIX_MCFG5 (AT91_MATRIX + 0x14) /* Master Configuration Register 5 */
-#define AT91_MATRIX_MCFG6 (AT91_MATRIX + 0x18) /* Master Configuration Register 6 */
-#define AT91_MATRIX_MCFG7 (AT91_MATRIX + 0x1C) /* Master Configuration Register 7 */
-#define AT91_MATRIX_MCFG8 (AT91_MATRIX + 0x20) /* Master Configuration Register 8 */
-#define AT91_MATRIX_MCFG9 (AT91_MATRIX + 0x24) /* Master Configuration Register 9 */
-#define AT91_MATRIX_MCFG10 (AT91_MATRIX + 0x28) /* Master Configuration Register 10 */
-#define AT91_MATRIX_MCFG11 (AT91_MATRIX + 0x2C) /* Master Configuration Register 11 */
-#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */
-#define AT91_MATRIX_ULBT_INFINITE (0 << 0)
-#define AT91_MATRIX_ULBT_SINGLE (1 << 0)
-#define AT91_MATRIX_ULBT_FOUR (2 << 0)
-#define AT91_MATRIX_ULBT_EIGHT (3 << 0)
-#define AT91_MATRIX_ULBT_SIXTEEN (4 << 0)
-
-#define AT91_MATRIX_SCFG0 (AT91_MATRIX + 0x40) /* Slave Configuration Register 0 */
-#define AT91_MATRIX_SCFG1 (AT91_MATRIX + 0x44) /* Slave Configuration Register 1 */
-#define AT91_MATRIX_SCFG2 (AT91_MATRIX + 0x48) /* Slave Configuration Register 2 */
-#define AT91_MATRIX_SCFG3 (AT91_MATRIX + 0x4C) /* Slave Configuration Register 3 */
-#define AT91_MATRIX_SCFG4 (AT91_MATRIX + 0x50) /* Slave Configuration Register 4 */
-#define AT91_MATRIX_SCFG5 (AT91_MATRIX + 0x54) /* Slave Configuration Register 5 */
-#define AT91_MATRIX_SCFG6 (AT91_MATRIX + 0x58) /* Slave Configuration Register 6 */
-#define AT91_MATRIX_SCFG7 (AT91_MATRIX + 0x5C) /* Slave Configuration Register 7 */
-#define AT91_MATRIX_SCFG8 (AT91_MATRIX + 0x60) /* Slave Configuration Register 8 */
-#define AT91_MATRIX_SCFG9 (AT91_MATRIX + 0x64) /* Slave Configuration Register 9 */
-#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */
-#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */
-#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16)
-#define AT91_MATRIX_DEFMSTR_TYPE_LAST (1 << 16)
-#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16)
-#define AT91_MATRIX_FIXED_DEFMSTR (0xf << 18) /* Fixed Index of Default Master */
-#define AT91_MATRIX_ARBT (3 << 24) /* Arbitration Type */
-#define AT91_MATRIX_ARBT_ROUND_ROBIN (0 << 24)
-#define AT91_MATRIX_ARBT_FIXED_PRIORITY (1 << 24)
-
-#define AT91_MATRIX_PRAS0 (AT91_MATRIX + 0x80) /* Priority Register A for Slave 0 */
-#define AT91_MATRIX_PRBS0 (AT91_MATRIX + 0x84) /* Priority Register B for Slave 0 */
-#define AT91_MATRIX_PRAS1 (AT91_MATRIX + 0x88) /* Priority Register A for Slave 1 */
-#define AT91_MATRIX_PRBS1 (AT91_MATRIX + 0x8C) /* Priority Register B for Slave 1 */
-#define AT91_MATRIX_PRAS2 (AT91_MATRIX + 0x90) /* Priority Register A for Slave 2 */
-#define AT91_MATRIX_PRBS2 (AT91_MATRIX + 0x94) /* Priority Register B for Slave 2 */
-#define AT91_MATRIX_PRAS3 (AT91_MATRIX + 0x98) /* Priority Register A for Slave 3 */
-#define AT91_MATRIX_PRBS3 (AT91_MATRIX + 0x9C) /* Priority Register B for Slave 3 */
-#define AT91_MATRIX_PRAS4 (AT91_MATRIX + 0xA0) /* Priority Register A for Slave 4 */
-#define AT91_MATRIX_PRBS4 (AT91_MATRIX + 0xA4) /* Priority Register B for Slave 4 */
-#define AT91_MATRIX_PRAS5 (AT91_MATRIX + 0xA8) /* Priority Register A for Slave 5 */
-#define AT91_MATRIX_PRBS5 (AT91_MATRIX + 0xAC) /* Priority Register B for Slave 5 */
-#define AT91_MATRIX_PRAS6 (AT91_MATRIX + 0xB0) /* Priority Register A for Slave 6 */
-#define AT91_MATRIX_PRBS6 (AT91_MATRIX + 0xB4) /* Priority Register B for Slave 6 */
-#define AT91_MATRIX_PRAS7 (AT91_MATRIX + 0xB8) /* Priority Register A for Slave 7 */
-#define AT91_MATRIX_PRBS7 (AT91_MATRIX + 0xBC) /* Priority Register B for Slave 7 */
-#define AT91_MATRIX_PRAS8 (AT91_MATRIX + 0xC0) /* Priority Register A for Slave 8 */
-#define AT91_MATRIX_PRBS8 (AT91_MATRIX + 0xC4) /* Priority Register B for Slave 8 */
-#define AT91_MATRIX_PRAS9 (AT91_MATRIX + 0xC8) /* Priority Register A for Slave 9 */
-#define AT91_MATRIX_PRBS9 (AT91_MATRIX + 0xCC) /* Priority Register B for Slave 9 */
-#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */
-#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */
-#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */
-#define AT91_MATRIX_M3PR (3 << 12) /* Master 3 Priority */
-#define AT91_MATRIX_M4PR (3 << 16) /* Master 4 Priority */
-#define AT91_MATRIX_M5PR (3 << 20) /* Master 5 Priority */
-#define AT91_MATRIX_M6PR (3 << 24) /* Master 6 Priority */
-#define AT91_MATRIX_M7PR (3 << 28) /* Master 7 Priority */
-#define AT91_MATRIX_M8PR (3 << 0) /* Master 8 Priority (in Register B) */
-#define AT91_MATRIX_M9PR (3 << 4) /* Master 9 Priority (in Register B) */
-#define AT91_MATRIX_M10PR (3 << 8) /* Master 10 Priority (in Register B) */
-#define AT91_MATRIX_M11PR (3 << 12) /* Master 11 Priority (in Register B) */
-
-#define AT91_MATRIX_MRCR (AT91_MATRIX + 0x100) /* Master Remap Control Register */
-#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
-#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
-#define AT91_MATRIX_RCB2 (1 << 2)
-#define AT91_MATRIX_RCB3 (1 << 3)
-#define AT91_MATRIX_RCB4 (1 << 4)
-#define AT91_MATRIX_RCB5 (1 << 5)
-#define AT91_MATRIX_RCB6 (1 << 6)
-#define AT91_MATRIX_RCB7 (1 << 7)
-#define AT91_MATRIX_RCB8 (1 << 8)
-#define AT91_MATRIX_RCB9 (1 << 9)
-#define AT91_MATRIX_RCB10 (1 << 10)
-#define AT91_MATRIX_RCB11 (1 << 11)
-
-#define AT91_MPBS0_SFR (AT91_MATRIX + 0x114) /* MPBlock Slave 0 Special Function Register */
-#define AT91_MPBS1_SFR (AT91_MATRIX + 0x11C) /* MPBlock Slave 1 Special Function Register */
-
-#define AT91_MATRIX_UDPHS (AT91_MATRIX + 0x118) /* USBHS Special Function Register [AT91CAP9 only] */
-#define AT91_MATRIX_SELECT_UDPHS (0 << 31) /* select High Speed UDP */
-#define AT91_MATRIX_SELECT_UDP (1 << 31) /* select standard UDP */
-#define AT91_MATRIX_UDPHS_BYPASS_LOCK (1 << 30) /* bypass lock bit */
-
-#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x120) /* EBI Chip Select Assignment Register */
-#define AT91_MATRIX_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */
-#define AT91_MATRIX_EBI_CS1A_SMC (0 << 1)
-#define AT91_MATRIX_EBI_CS1A_BCRAMC (1 << 1)
-#define AT91_MATRIX_EBI_CS3A (1 << 3) /* Chip Select 3 Assignment */
-#define AT91_MATRIX_EBI_CS3A_SMC (0 << 3)
-#define AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA (1 << 3)
-#define AT91_MATRIX_EBI_CS4A (1 << 4) /* Chip Select 4 Assignment */
-#define AT91_MATRIX_EBI_CS4A_SMC (0 << 4)
-#define AT91_MATRIX_EBI_CS4A_SMC_CF1 (1 << 4)
-#define AT91_MATRIX_EBI_CS5A (1 << 5) /* Chip Select 5 Assignment */
-#define AT91_MATRIX_EBI_CS5A_SMC (0 << 5)
-#define AT91_MATRIX_EBI_CS5A_SMC_CF2 (1 << 5)
-#define AT91_MATRIX_EBI_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */
-#define AT91_MATRIX_EBI_DQSPDC (1 << 9) /* Data Qualifier Strobe Pull-Down Configuration */
-#define AT91_MATRIX_EBI_VDDIOMSEL (1 << 16) /* Memory voltage selection */
-#define AT91_MATRIX_EBI_VDDIOMSEL_1_8V (0 << 16)
-#define AT91_MATRIX_EBI_VDDIOMSEL_3_3V (1 << 16)
-
-#define AT91_MPBS2_SFR (AT91_MATRIX + 0x12C) /* MPBlock Slave 2 Special Function Register */
-#define AT91_MPBS3_SFR (AT91_MATRIX + 0x130) /* MPBlock Slave 3 Special Function Register */
-#define AT91_APB_SFR (AT91_MATRIX + 0x134) /* APB Bridge Special Function Register */
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9_ddrsdr.h b/arch/arm/mach-at91/include/mach/at91sam9_ddrsdr.h
index e2f8da8..5d4a9f8 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9_ddrsdr.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9_ddrsdr.h
@@ -59,7 +59,6 @@
#define AT91_DDRSDRC_TRP (0xf << 16) /* Row precharge delay */
#define AT91_DDRSDRC_TRRD (0xf << 20) /* Active BankA to BankB */
#define AT91_DDRSDRC_TWTR (0x7 << 24) /* Internal Write to Read delay */
-#define AT91CAP9_DDRSDRC_TWTR (1 << 24) /* Internal Write to Read delay */
#define AT91_DDRSDRC_RED_WRRD (0x1 << 27) /* Reduce Write to Read Delay [SAM9 Only] */
#define AT91_DDRSDRC_TMRD (0xf << 28) /* Load mode to active/refresh delay */
@@ -76,7 +75,6 @@
#define AT91_DDRSDRC_TRTP (0x7 << 12) /* Read to Precharge delay */
#define AT91_DDRSDRC_LPR 0x1C /* Low Power Register */
-#define AT91CAP9_DDRSDRC_LPR 0x18 /* Low Power Register */
#define AT91_DDRSDRC_LPCB (3 << 0) /* Low-power Configurations */
#define AT91_DDRSDRC_LPCB_DISABLE 0
#define AT91_DDRSDRC_LPCB_SELF_REFRESH 1
@@ -94,11 +92,9 @@
#define AT91_DDRSDRC_UPD_MR (3 << 20) /* Update load mode register and extended mode register */
#define AT91_DDRSDRC_MDR 0x20 /* Memory Device Register */
-#define AT91CAP9_DDRSDRC_MDR 0x1C /* Memory Device Register */
#define AT91_DDRSDRC_MD (3 << 0) /* Memory Device Type */
#define AT91_DDRSDRC_MD_SDR 0
#define AT91_DDRSDRC_MD_LOW_POWER_SDR 1
-#define AT91CAP9_DDRSDRC_MD_DDR 2
#define AT91_DDRSDRC_MD_LOW_POWER_DDR 3
#define AT91_DDRSDRC_MD_DDR2 6 /* [SAM9 Only] */
#define AT91_DDRSDRC_DBW (1 << 4) /* Data Bus Width */
@@ -106,16 +102,10 @@
#define AT91_DDRSDRC_DBW_16BITS (1 << 4)
#define AT91_DDRSDRC_DLL 0x24 /* DLL Information Register */
-#define AT91CAP9_DDRSDRC_DLL 0x20 /* DLL Information Register */
#define AT91_DDRSDRC_MDINC (1 << 0) /* Master Delay increment */
#define AT91_DDRSDRC_MDDEC (1 << 1) /* Master Delay decrement */
#define AT91_DDRSDRC_MDOVF (1 << 2) /* Master Delay Overflow */
-#define AT91CAP9_DDRSDRC_SDCOVF (1 << 3) /* Slave Delay Correction Overflow */
-#define AT91CAP9_DDRSDRC_SDCUDF (1 << 4) /* Slave Delay Correction Underflow */
-#define AT91CAP9_DDRSDRC_SDERF (1 << 5) /* Slave Delay Correction error */
#define AT91_DDRSDRC_MDVAL (0xff << 8) /* Master Delay value */
-#define AT91CAP9_DDRSDRC_SDVAL (0xff << 16) /* Slave Delay value */
-#define AT91CAP9_DDRSDRC_SDCVAL (0xff << 24) /* Slave Delay Correction value */
#define AT91_DDRSDRC_HS 0x2C /* High Speed Register [SAM9 Only] */
#define AT91_DDRSDRC_DIS_ATCP_RD (1 << 2) /* Anticip read access is disabled */
diff --git a/arch/arm/mach-at91/include/mach/cpu.h b/arch/arm/mach-at91/include/mach/cpu.h
index f6ce936..0118c33 100644
--- a/arch/arm/mach-at91/include/mach/cpu.h
+++ b/arch/arm/mach-at91/include/mach/cpu.h
@@ -25,7 +25,6 @@
#define ARCH_ID_AT91SAM9G45MRL 0x819b05a2 /* aka 9G45-ES2 & non ES lots */
#define ARCH_ID_AT91SAM9G45ES 0x819b05a1 /* 9G45-ES (Engineering Sample) */
#define ARCH_ID_AT91SAM9X5 0x819a05a0
-#define ARCH_ID_AT91CAP9 0x039A03A0
#define ARCH_ID_AT91SAM9XE128 0x329973a0
#define ARCH_ID_AT91SAM9XE256 0x329a93a0
@@ -51,10 +50,6 @@
#define ARCH_FAMILY_AT91SAM9 0x01900000
#define ARCH_FAMILY_AT91SAM9XE 0x02900000
-/* PMC revision */
-#define ARCH_REVISION_CAP9_B 0x399
-#define ARCH_REVISION_CAP9_C 0x601
-
/* RM9200 type */
#define ARCH_REVISON_9200_BGA (0 << 0)
#define ARCH_REVISON_9200_PQFP (1 << 0)
@@ -63,9 +58,6 @@ enum at91_soc_type {
/* 920T */
AT91_SOC_RM9200,
- /* CAP */
- AT91_SOC_CAP9,
-
/* SAM92xx */
AT91_SOC_SAM9260, AT91_SOC_SAM9261, AT91_SOC_SAM9263,
@@ -86,9 +78,6 @@ enum at91_soc_subtype {
/* RM9200 */
AT91_SOC_RM9200_BGA, AT91_SOC_RM9200_PQFP,
- /* CAP9 */
- AT91_SOC_CAP9_REV_B, AT91_SOC_CAP9_REV_C,
-
/* SAM9260 */
AT91_SOC_SAM9XE,
@@ -195,16 +184,6 @@ static inline int at91_soc_is_detected(void)
#define cpu_is_at91sam9x25() (0)
#endif
-#ifdef CONFIG_ARCH_AT91CAP9
-#define cpu_is_at91cap9() (at91_soc_initdata.type == AT91_SOC_CAP9)
-#define cpu_is_at91cap9_revB() (at91_soc_initdata.subtype == AT91_SOC_CAP9_REV_B)
-#define cpu_is_at91cap9_revC() (at91_soc_initdata.subtype == AT91_SOC_CAP9_REV_C)
-#else
-#define cpu_is_at91cap9() (0)
-#define cpu_is_at91cap9_revB() (0)
-#define cpu_is_at91cap9_revC() (0)
-#endif
-
/*
* Since this is ARM, we will never run on any AVR32 CPU. But these
* definitions may reduce clutter in common drivers.
diff --git a/arch/arm/mach-at91/include/mach/hardware.h b/arch/arm/mach-at91/include/mach/hardware.h
index 12ad180..fd7dce4 100644
--- a/arch/arm/mach-at91/include/mach/hardware.h
+++ b/arch/arm/mach-at91/include/mach/hardware.h
@@ -19,7 +19,7 @@
/* DBGU base */
/* rm9200, 9260/9g20, 9261/9g10, 9rl */
#define AT91_BASE_DBGU0 0xfffff200
-/* 9263, 9g45, cap9 */
+/* 9263, 9g45 */
#define AT91_BASE_DBGU1 0xffffee00
#if defined(CONFIG_ARCH_AT91RM9200)
@@ -36,8 +36,6 @@
#include <mach/at91sam9g45.h>
#elif defined(CONFIG_ARCH_AT91SAM9X5)
#include <mach/at91sam9x5.h>
-#elif defined(CONFIG_ARCH_AT91CAP9)
-#include <mach/at91cap9.h>
#elif defined(CONFIG_ARCH_AT91X40)
#include <mach/at91x40.h>
#else
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index 1606379..87be5aa 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -150,11 +150,6 @@ static int at91_pm_verify_clocks(void)
pr_err("AT91: PM - Suspend-to-RAM with USB still active\n");
return 0;
}
- } else if (cpu_is_at91cap9()) {
- if ((scsr & AT91CAP9_PMC_UHP) != 0) {
- pr_err("AT91: PM - Suspend-to-RAM with USB still active\n");
- return 0;
- }
}
#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS
diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h
index 7eb40d2..218d816 100644
--- a/arch/arm/mach-at91/pm.h
+++ b/arch/arm/mach-at91/pm.h
@@ -24,24 +24,6 @@ static inline u32 sdram_selfrefresh_enable(void)
#define wait_for_interrupt_enable() asm volatile ("mcr p15, 0, %0, c7, c0, 4" \
: : "r" (0))
-#elif defined(CONFIG_ARCH_AT91CAP9)
-#include <mach/at91sam9_ddrsdr.h>
-
-
-static inline u32 sdram_selfrefresh_enable(void)
-{
- u32 saved_lpr, lpr;
-
- saved_lpr = at91_ramc_read(0, AT91CAP9_DDRSDRC_LPR);
-
- lpr = saved_lpr & ~AT91_DDRSDRC_LPCB;
- at91_ramc_write(0, AT91CAP9_DDRSDRC_LPR, lpr | AT91_DDRSDRC_LPCB_SELF_REFRESH);
- return saved_lpr;
-}
-
-#define sdram_selfrefresh_disable(saved_lpr) at91_ramc_write(0, AT91CAP9_DDRSDRC_LPR, saved_lpr)
-#define wait_for_interrupt_enable() cpu_do_idle()
-
#elif defined(CONFIG_ARCH_AT91SAM9G45)
#include <mach/at91sam9_ddrsdr.h>
diff --git a/arch/arm/mach-at91/pm_slowclock.S b/arch/arm/mach-at91/pm_slowclock.S
index 92dfb84..f8539a8 100644
--- a/arch/arm/mach-at91/pm_slowclock.S
+++ b/arch/arm/mach-at91/pm_slowclock.S
@@ -18,8 +18,7 @@
#if defined(CONFIG_ARCH_AT91RM9200)
#include <mach/at91rm9200_mc.h>
-#elif defined(CONFIG_ARCH_AT91CAP9) \
- || defined(CONFIG_ARCH_AT91SAM9G45)
+#elif defined(CONFIG_ARCH_AT91SAM9G45)
#include <mach/at91sam9_ddrsdr.h>
#else
#include <mach/at91sam9_sdramc.h>
@@ -130,8 +129,7 @@ ENTRY(at91_slow_clock)
/* Put SDRAM in self-refresh mode */
mov r3, #1
str r3, [r2, #AT91_SDRAMC_SRR]
-#elif defined(CONFIG_ARCH_AT91CAP9) \
- || defined(CONFIG_ARCH_AT91SAM9G45)
+#elif defined(CONFIG_ARCH_AT91SAM9G45)
/* prepare for DDRAM self-refresh mode */
ldr r3, [r2, #AT91_DDRSDRC_LPR]
@@ -263,8 +261,7 @@ ENTRY(at91_slow_clock)
#ifdef CONFIG_ARCH_AT91RM9200
/* Do nothing - self-refresh is automatically disabled. */
-#elif defined(CONFIG_ARCH_AT91CAP9) \
- || defined(CONFIG_ARCH_AT91SAM9G45)
+#elif defined(CONFIG_ARCH_AT91SAM9G45)
/* Restore LPR on AT91 with DDRAM */
ldr r3, .saved_sam9_lpr
str r3, [r2, #AT91_DDRSDRC_LPR]
@@ -305,8 +302,7 @@ ENTRY(at91_slow_clock)
#ifdef CONFIG_ARCH_AT91RM9200
.at91_va_base_sdramc:
.word AT91_VA_BASE_SYS
-#elif defined(CONFIG_ARCH_AT91CAP9) \
- || defined(CONFIG_ARCH_AT91SAM9G45)
+#elif defined(CONFIG_ARCH_AT91SAM9G45)
.at91_va_base_sdramc:
.word AT91_VA_BASE_SYS + AT91_DDRSDRC0
#else
diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c
index 69d3fc4..620c67e 100644
--- a/arch/arm/mach-at91/setup.c
+++ b/arch/arm/mach-at91/setup.c
@@ -86,20 +86,6 @@ static void __init soc_detect(u32 dbgu_base)
socid = cidr & ~AT91_CIDR_VERSION;
switch (socid) {
- case ARCH_ID_AT91CAP9: {
-#ifdef CONFIG_AT91_PMC_UNIT
- u32 pmc_ver = at91_sys_read(AT91_PMC_VER);
-
- if (pmc_ver == ARCH_REVISION_CAP9_B)
- at91_soc_initdata.subtype = AT91_SOC_CAP9_REV_B;
- else if (pmc_ver == ARCH_REVISION_CAP9_C)
- at91_soc_initdata.subtype = AT91_SOC_CAP9_REV_C;
-#endif
- at91_soc_initdata.type = AT91_SOC_CAP9;
- at91_boot_soc = at91cap9_soc;
- break;
- }
-
case ARCH_ID_AT91RM9200:
at91_soc_initdata.type = AT91_SOC_RM9200;
at91_boot_soc = at91rm9200_soc;
@@ -200,7 +186,6 @@ static void __init soc_detect(u32 dbgu_base)
static const char *soc_name[] = {
[AT91_SOC_RM9200] = "at91rm9200",
- [AT91_SOC_CAP9] = "at91cap9",
[AT91_SOC_SAM9260] = "at91sam9260",
[AT91_SOC_SAM9261] = "at91sam9261",
[AT91_SOC_SAM9263] = "at91sam9263",
@@ -221,8 +206,6 @@ EXPORT_SYMBOL(at91_get_soc_type);
static const char *soc_subtype_name[] = {
[AT91_SOC_RM9200_BGA] = "at91rm9200 BGA",
[AT91_SOC_RM9200_PQFP] = "at91rm9200 PQFP",
- [AT91_SOC_CAP9_REV_B] = "at91cap9 revB",
- [AT91_SOC_CAP9_REV_C] = "at91cap9 revC",
[AT91_SOC_SAM9XE] = "at91sam9xe",
[AT91_SOC_SAM9G45ES] = "at91sam9g45es",
[AT91_SOC_SAM9M10] = "at91sam9m10",
diff --git a/arch/arm/mach-at91/soc.h b/arch/arm/mach-at91/soc.h
index 4588ae6..5db4aa4 100644
--- a/arch/arm/mach-at91/soc.h
+++ b/arch/arm/mach-at91/soc.h
@@ -13,7 +13,6 @@ struct at91_init_soc {
};
extern struct at91_init_soc at91_boot_soc;
-extern struct at91_init_soc at91cap9_soc;
extern struct at91_init_soc at91rm9200_soc;
extern struct at91_init_soc at91sam9260_soc;
extern struct at91_init_soc at91sam9261_soc;
@@ -27,10 +26,6 @@ static inline int at91_soc_is_enabled(void)
return at91_boot_soc.init != NULL;
}
-#if !defined(CONFIG_ARCH_AT91CAP9)
-#define at91cap9_soc at91_boot_soc
-#endif
-
#if !defined(CONFIG_ARCH_AT91RM9200)
#define at91rm9200_soc at91_boot_soc
#endif
diff --git a/arch/avr32/mach-at32ap/include/mach/cpu.h b/arch/avr32/mach-at32ap/include/mach/cpu.h
index 8181293..16a24b1 100644
--- a/arch/avr32/mach-at32ap/include/mach/cpu.h
+++ b/arch/avr32/mach-at32ap/include/mach/cpu.h
@@ -30,9 +30,6 @@
#define cpu_is_at91sam9261() (0)
#define cpu_is_at91sam9263() (0)
#define cpu_is_at91sam9rl() (0)
-#define cpu_is_at91cap9() (0)
-#define cpu_is_at91cap9_revB() (0)
-#define cpu_is_at91cap9_revC() (0)
#define cpu_is_at91sam9g10() (0)
#define cpu_is_at91sam9g20() (0)
#define cpu_is_at91sam9g45() (0)
diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c
index 947faa5..efdb81d 100644
--- a/drivers/mmc/host/at91_mci.c
+++ b/drivers/mmc/host/at91_mci.c
@@ -86,7 +86,6 @@ static inline int at91mci_is_mci1rev2xx(void)
{
return ( cpu_is_at91sam9260()
|| cpu_is_at91sam9263()
- || cpu_is_at91cap9()
|| cpu_is_at91sam9rl()
|| cpu_is_at91sam9g10()
|| cpu_is_at91sam9g20()
diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
index 7ecb68a..85ae4b4 100644
--- a/drivers/usb/gadget/Kconfig
+++ b/drivers/usb/gadget/Kconfig
@@ -137,7 +137,7 @@ choice
config USB_AT91
tristate "Atmel AT91 USB Device Port"
- depends on ARCH_AT91 && !ARCH_AT91SAM9RL && !ARCH_AT91CAP9 && !ARCH_AT91SAM9G45
+ depends on ARCH_AT91 && !ARCH_AT91SAM9RL && !ARCH_AT91SAM9G45
help
Many Atmel AT91 processors (such as the AT91RM2000) have a
full speed USB Device Port with support for five configurable
@@ -150,7 +150,7 @@ config USB_AT91
config USB_ATMEL_USBA
tristate "Atmel USBA"
select USB_GADGET_DUALSPEED
- depends on AVR32 || ARCH_AT91CAP9 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
+ depends on AVR32 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
help
USBA is the integrated high-speed USB Device controller on
the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel.
--
1.7.7
More information about the linux-arm-kernel
mailing list