[PATCH 3/3] ARM: AT91: Add the ADC to the sam9g20ek board

[Nicolas Ferre]

On 01/16/2012 10:36 PM, Maxime Ripard :
> Signed-off-by: Maxime Ripard <maxime.ripard at free-electrons.com>
> 
> Cc: Nicolas Ferre <nicolas.ferre at atmel.com>

Signed-off-by: Nicolas Ferre <nicolas.ferre at atmel.com>

> Cc: Patrice Vilchez <patrice.vilchez at atmel.com>
> Cc: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
> ---
>  arch/arm/mach-at91/at91sam9260_devices.c |   53 ++++++++++++++++++++++++++++++
>  arch/arm/mach-at91/board-sam9g20ek.c     |   13 +++++++
>  2 files changed, 66 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
> index 39f81f4..3598540 100644
> --- a/arch/arm/mach-at91/at91sam9260_devices.c
> +++ b/arch/arm/mach-at91/at91sam9260_devices.c
> @@ -16,6 +16,8 @@
>  #include <linux/platform_device.h>
>  #include <linux/i2c-gpio.h>
>  
> +#include <linux/platform_data/at91_adc.h>
> +
>  #include <mach/board.h>
>  #include <mach/gpio.h>
>  #include <mach/cpu.h>
> @@ -1312,6 +1314,57 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
>  void __init at91_add_device_cf(struct at91_cf_data * data) {}
>  #endif
>  
> +/* --------------------------------------------------------------------
> + *  ADCs
> + * -------------------------------------------------------------------- */
> +
> +#if defined(CONFIG_IIO_AT91_ADC) || defined(CONFIG_IIO_AT91_ADC_MODULE)
> +static struct at91_adc_data adc_data;
> +
> +static struct resource adc_resources[] = {
> +	[0] = {
> +		.start	= AT91SAM9260_BASE_ADC,
> +		.end	= AT91SAM9260_BASE_ADC + SZ_16K - 1,
> +		.flags	= IORESOURCE_MEM,
> +	},
> +	[1] = {
> +		.start	= AT91SAM9260_ID_ADC,
> +		.end	= AT91SAM9260_ID_ADC,
> +		.flags	= IORESOURCE_IRQ,
> +	},
> +};
> +
> +static struct platform_device at91_adc_device = {
> +	.name		= "at91_adc",
> +	.id		= -1,
> +	.dev		= {
> +				.platform_data		= &adc_data,
> +	},
> +	.resource	= adc_resources,
> +	.num_resources	= ARRAY_SIZE(adc_resources),
> +};
> +
> +void __init at91_add_device_adc(struct at91_adc_data *data)
> +{
> +	if (!data)
> +		return;
> +
> +	if (test_bit(0, &data->channels_used))
> +		at91_set_A_periph(AT91_PIN_PC0, 0);
> +	if (test_bit(1, &data->channels_used))
> +		at91_set_A_periph(AT91_PIN_PC1, 0);
> +	if (test_bit(2, &data->channels_used))
> +		at91_set_A_periph(AT91_PIN_PC2, 0);
> +	if (test_bit(3, &data->channels_used))
> +		at91_set_A_periph(AT91_PIN_PC3, 0);
> +
> +	adc_data = *data;
> +	platform_device_register(&at91_adc_device);
> +}
> +#else
> +void __init at91_add_device_adc(struct at91_adc_data *data) {}
> +#endif
> +
>  /* -------------------------------------------------------------------- */
>  /*
>   * These devices are always present and don't need any board-specific
> diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
> index 817f59d..29dae9f 100644
> --- a/arch/arm/mach-at91/board-sam9g20ek.c
> +++ b/arch/arm/mach-at91/board-sam9g20ek.c
> @@ -31,6 +31,8 @@
>  #include <linux/regulator/fixed.h>
>  #include <linux/regulator/consumer.h>
>  
> +#include <linux/platform_data/at91_adc.h>
> +
>  #include <mach/hardware.h>
>  #include <asm/setup.h>
>  #include <asm/mach-types.h>
> @@ -314,6 +316,15 @@ static void __init ek_add_device_buttons(void)
>  static void __init ek_add_device_buttons(void) {}
>  #endif
>  
> +/*
> + * ADCs
> + */
> +
> +static struct at91_adc_data ek_adc_data = {
> +	.channels_used = BIT(0) | BIT(1) | BIT(2) | BIT(3),
> +	.vref = 3300,
> +};
> +
>  #if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
>  static struct regulator_consumer_supply ek_audio_consumer_supplies[] = {
>  	REGULATOR_SUPPLY("AVDD", "0-001b"),
> @@ -389,6 +400,8 @@ static void __init ek_board_init(void)
>  	ek_add_device_gpio_leds();
>  	/* Push Buttons */
>  	ek_add_device_buttons();
> +	/* ADCs */
> +	at91_add_device_adc(&ek_adc_data);
>  	/* PCK0 provides MCLK to the WM8731 */
>  	at91_set_B_periph(AT91_PIN_PC1, 0);
>  	/* SSC (for WM8731) */


-- 
Nicolas Ferre