[PATCH] ARM: Exynos: Use lcd power control driver for lcd panel

[Thomas Abraham]

The Hydis hv070wsa lcd panel used with the Origen board uses a gpio
for reset and the Vcc supply to the panel can be controlled using
a voltage regulator. Switch to using the lcd power control driver
for controlling the power to the lcd panel.

Signed-off-by: Thomas Abraham <thomas.abraham at linaro.org>
---
The 'apply_uV' of buck7 regulator which controls the Vcc of the lcd panel
is modified to be 0. The regulator need not start supplying power to the
lcd panel at boot time. The lcd driver will turn on the power to the lcd
panel when frame buffer driver has to output data to the lcd panel.

 arch/arm/mach-exynos/mach-origen.c |   36 +++++++++++-------------------------
 1 files changed, 11 insertions(+), 25 deletions(-)

diff --git a/arch/arm/mach-exynos/mach-origen.c b/arch/arm/mach-exynos/mach-origen.c
index 23fc5cb..522fad7 100644
--- a/arch/arm/mach-exynos/mach-origen.c
+++ b/arch/arm/mach-exynos/mach-origen.c
@@ -25,7 +25,7 @@
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
 
-#include <video/platform_lcd.h>
+#include <video/lcd_pwrctrl.h>
 
 #include <plat/regs-serial.h>
 #include <plat/regs-fb-v4.h>
@@ -127,7 +127,7 @@ static struct regulator_consumer_supply __initdata buck3_consumer[] = {
 	REGULATOR_SUPPLY("vdd_g3d", "mali_drm"), /* G3D */
 };
 static struct regulator_consumer_supply __initdata buck7_consumer[] = {
-	REGULATOR_SUPPLY("vcc", "platform-lcd"), /* LCD */
+	REGULATOR_SUPPLY("vcc-lcd", "lcd-pwrctrl.0"), /* LCD */
 };
 
 static struct regulator_init_data __initdata max8997_ldo1_data = {
@@ -382,9 +382,10 @@ static struct regulator_init_data __initdata max8997_buck7_data = {
 		.name		= "VDD_LCD_3.3V",
 		.min_uV		= 3300000,
 		.max_uV		= 3300000,
-		.boot_on	= 1,
-		.apply_uV	= 1,
-		.valid_ops_mask	= REGULATOR_CHANGE_STATUS,
+		.boot_on	= 0,
+		.apply_uV	= 0,
+		.valid_ops_mask	= REGULATOR_CHANGE_STATUS |
+					REGULATOR_CHANGE_VOLTAGE,
 		.state_mem	= {
 			.disabled	= 1
 		},
@@ -554,29 +555,14 @@ static struct platform_device origen_device_gpiokeys = {
 	},
 };
 
-static void lcd_hv070wsa_set_power(struct plat_lcd_data *pd, unsigned int power)
-{
-	int ret;
-
-	if (power)
-		ret = gpio_request_one(EXYNOS4_GPE3(4),
-					GPIOF_OUT_INIT_HIGH, "GPE3_4");
-	else
-		ret = gpio_request_one(EXYNOS4_GPE3(4),
-					GPIOF_OUT_INIT_LOW, "GPE3_4");
-
-	gpio_free(EXYNOS4_GPE3(4));
-
-	if (ret)
-		pr_err("failed to request gpio for LCD power: %d\n", ret);
-}
-
-static struct plat_lcd_data origen_lcd_hv070wsa_data = {
-	.set_power = lcd_hv070wsa_set_power,
+static struct lcd_pwrctrl_data origen_lcd_hv070wsa_data = {
+	.gpio	= EXYNOS4_GPE3(4),
+	.min_uV = 3300000,
+	.max_uV	= 3300000,
 };
 
 static struct platform_device origen_lcd_hv070wsa = {
-	.name			= "platform-lcd",
+	.name			= "lcd-pwrctrl",
 	.dev.parent		= &s5p_device_fimd0.dev,
 	.dev.platform_data	= &origen_lcd_hv070wsa_data,
 };
-- 
1.6.6.rc2