[PATCH v5 1/2] pxa/hx4700: Add Synaptics NavPoint (PXA27x SSP/SPI) driver
Shubhrajyoti
shubhrajyoti at ti.com
Mon Jan 2 01:26:52 EST 2012
Hi Paul,
Some minor comments / suggestions
On Saturday 31 December 2011 07:16 PM, Paul Parsons wrote:
> Add support for the Synaptics NavPoint touchpad connected to a PXA27x SSP port
> in SPI slave mode. The driver implements a simple navigation pad. The four
> raised dots are mapped to UP/DOWN/LEFT/RIGHT buttons and the centre of the
> touchpad is mapped to the ENTER button.
>
> Signed-off-by: Paul Parsons <lost.distance at yahoo.com>
> ---
>
> V5:
> Workaround for HaRET, which does not disable devices before jumping into Linux.
> Rebased to linux-3.2-rc7.
>
> diff -uprN clean-3.2-rc7/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h linux-3.2-rc7/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h
> --- clean-3.2-rc7/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h 2011-12-24 05:51:06.000000000 +0000
> +++ linux-3.2-rc7/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h 2011-12-31 11:54:02.859594707 +0000
> @@ -206,6 +206,7 @@
> #define GPIO113_I2S_SYSCLK MFP_CFG_OUT(GPIO113, AF1, DRIVE_LOW)
>
> /* SSP 1 */
> +#define GPIO23_SSP1_SCLK_IN MFP_CFG_IN(GPIO23, AF2)
> #define GPIO23_SSP1_SCLK MFP_CFG_OUT(GPIO23, AF2, DRIVE_LOW)
> #define GPIO29_SSP1_SCLK MFP_CFG_IN(GPIO29, AF3)
> #define GPIO27_SSP1_SYSCLK MFP_CFG_OUT(GPIO27, AF1, DRIVE_LOW)
> diff -uprN clean-3.2-rc7/drivers/input/mouse/Kconfig linux-3.2-rc7/drivers/input/mouse/Kconfig
> --- clean-3.2-rc7/drivers/input/mouse/Kconfig 2011-12-24 05:51:06.000000000 +0000
> +++ linux-3.2-rc7/drivers/input/mouse/Kconfig 2011-12-31 11:54:02.859594707 +0000
> @@ -322,4 +322,13 @@ config MOUSE_SYNAPTICS_I2C
> To compile this driver as a module, choose M here: the
> module will be called synaptics_i2c.
>
> +config MOUSE_NAVPOINT_PXA27x
> + tristate "Synaptics NavPoint (PXA27x SSP/SPI)"
> + depends on PXA27x && PXA_SSP
> + help
> + This option enables support for the Synaptics NavPoint connected to
> + a PXA27x SSP port in SPI slave mode. The driver implements a simple
> + navigation pad. The four raised dots are mapped to UP/DOWN/LEFT/RIGHT
> + buttons and the centre of the touchpad is mapped to the ENTER button.
Maybe some help on module building as tristate.
> +
> endif
> diff -uprN clean-3.2-rc7/drivers/input/mouse/Makefile linux-3.2-rc7/drivers/input/mouse/Makefile
> --- clean-3.2-rc7/drivers/input/mouse/Makefile 2011-12-24 05:51:06.000000000 +0000
> +++ linux-3.2-rc7/drivers/input/mouse/Makefile 2011-12-31 11:54:02.859594707 +0000
> @@ -12,6 +12,7 @@ obj-$(CONFIG_MOUSE_GPIO) += gpio_mouse.
> obj-$(CONFIG_MOUSE_INPORT) += inport.o
> obj-$(CONFIG_MOUSE_LOGIBM) += logibm.o
> obj-$(CONFIG_MOUSE_MAPLE) += maplemouse.o
> +obj-$(CONFIG_MOUSE_NAVPOINT_PXA27x) += navpoint.o
> obj-$(CONFIG_MOUSE_PC110PAD) += pc110pad.o
> obj-$(CONFIG_MOUSE_PS2) += psmouse.o
> obj-$(CONFIG_MOUSE_PXA930_TRKBALL) += pxa930_trkball.o
> diff -uprN clean-3.2-rc7/drivers/input/mouse/navpoint.c linux-3.2-rc7/drivers/input/mouse/navpoint.c
> --- clean-3.2-rc7/drivers/input/mouse/navpoint.c 1970-01-01 01:00:00.000000000 +0100
> +++ linux-3.2-rc7/drivers/input/mouse/navpoint.c 2011-12-31 11:58:45.563587396 +0000
> @@ -0,0 +1,337 @@
> +/*
> + * Copyright (C) 2011 Paul Parsons <lost.distance at yahoo.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/gpio.h>
> +#include <linux/input.h>
> +#include <linux/input/navpoint.h>
> +#include <linux/interrupt.h>
> +#include <linux/pxa2xx_ssp.h>
> +#include <linux/slab.h>
> +
> +/*
> + * Synaptics NavPoint (PXA27x SSP/SPI) driver.
> + */
> +
> +/*
> + * Synaptics Modular Embedded Protocol: Module Packet Format.
> + * Module header byte 2:0 = Length (# bytes that follow)
> + * Module header byte 4:3 = Control
> + * Module header byte 7:5 = Module Address
> + */
> +#define HEADER_LENGTH(byte) ((byte) & 0x07)
> +#define HEADER_CONTROL(byte) (((byte) >> 3) & 0x03)
> +#define HEADER_ADDRESS(byte) ((byte) >> 5)
> +
> +struct driver_data {
> + struct ssp_device *ssp;
> + int gpio;
> + struct input_dev *input;
> + int index;
> + uint8_t data[1+HEADER_LENGTH(0xff)];
> + int pressed; /* 1 = pressed, 0 = released */
Could this be bool ?
> + unsigned code; /* Code of last key pressed */
> +};
> +
> +static const u32 sscr0 = 0
> + | SSCR0_TUM /* TIM = 1; No TUR interrupts */
> + | SSCR0_RIM /* RIM = 1; No ROR interrupts */
> + | SSCR0_SSE /* SSE = 1; SSP enabled */
> + | SSCR0_Motorola /* FRF = 0; Motorola SPI */
> + | SSCR0_DataSize(16) /* DSS = 15; Data size = 16-bit */
> + ;
> +static const u32 sscr1 = 0
> + | SSCR1_SCFR /* SCFR = 1; SSPSCLK only during transfers */
> + | SSCR1_SCLKDIR /* SCLKDIR = 1; Slave mode */
> + | SSCR1_SFRMDIR /* SFRMDIR = 1; Slave mode */
> + | SSCR1_RWOT /* RWOT = 1; Receive without transmit mode */
> + | SSCR1_RxTresh(1) /* RFT = 0; Receive FIFO threshold = 1 */
> + | SSCR1_SPH /* SPH = 1; SSPSCLK inactive 0.5 + 1 cycles */
> + | SSCR1_RIE /* RIE = 1; Receive FIFO interrupt enabled */
> + ;
> +static const u32 sssr = 0
> + | SSSR_BCE /* BCE = 1; Clear BCE */
> + | SSSR_TUR /* TUR = 1; Clear TUR */
> + | SSSR_EOC /* EOC = 1; Clear EOC */
> + | SSSR_TINT /* TINT = 1; Clear TINT */
> + | SSSR_PINT /* PINT = 1; Clear PINT */
> + | SSSR_ROR /* ROR = 1; Clear ROR */
> + ;
> +
> +/*
> + * MEP Query $22: Touchpad Coordinate Range Query is not supported by
> + * the NavPoint module, so sampled values provide the default limits.
> + */
> +
> +static int west = 2416; /* 1/3 width */
> +module_param(west, int, 0644);
> +MODULE_PARM_DESC(west, "X coordinate limit for KEY_LEFT. Default = 2416");
> +static int east = 3904; /* 2/3 width */
> +module_param(east, int, 0644);
> +MODULE_PARM_DESC(east, "X coordinate limit for KEY_RIGHT. Default = 3904");
> +static int south = 2480; /* 1/3 height */
> +module_param(south, int, 0644);
> +MODULE_PARM_DESC(south, "Y coordinate limit for KEY_DOWN. Default = 2480");
> +static int north = 3424; /* 2/3 height */
> +module_param(north, int, 0644);
> +MODULE_PARM_DESC(north, "Y coordinate limit for KEY_UP. Default = 3424");
> +
> +static void navpoint_packet(struct device *dev)
> +{
> + struct driver_data *drv_data = dev_get_drvdata(dev);
> + int pressed;
> + unsigned x, y;
> + unsigned code;
> +
> + switch (drv_data->data[0]) {
> + case 0xff: /* Garbage (packet?) between reset and Hello packet */
> + case 0x00: /* Module 0, NULL packet */
> + break;
> + case 0x0e: /* Module 0, Absolute packet */
> + pressed = (drv_data->data[1] & 0x01);
> + if ((drv_data->pressed ^ pressed) == 0) /* No change */
> + break;
> + drv_data->pressed = pressed;
> + x = ((drv_data->data[2] & 0x1f) << 8) | drv_data->data[3];
> + y = ((drv_data->data[4] & 0x1f) << 8) | drv_data->data[5];
> + if (x < west)
> + code = KEY_LEFT;
> + else if (x > east)
> + code = KEY_RIGHT;
> + else if (y < south)
> + code = KEY_DOWN;
> + else if (y > north)
> + code = KEY_UP;
> + else
> + code = KEY_ENTER;
> + if (pressed)
> + drv_data->code = code;
> + input_report_key(drv_data->input, drv_data->code, pressed);
> + input_sync(drv_data->input);
> + break;
> + case 0x19: /* Module 0, Hello packet */
> + if ((drv_data->data[1] & 0xf0) == 0x10)
> + break;
> + /* FALLTHROUGH */
> + default:
> + dev_warn(dev, "spurious packet: 0x%02x,0x%02x,...\n",
> + drv_data->data[0],
> + drv_data->data[1]);
> + break;
> + }
> +
> + drv_data->index = 0;
> +}
> +
> +static irqreturn_t navpoint_int(int irq, void *dev_id)
> +{
> + struct device *dev = dev_id;
> + struct driver_data *drv_data = dev_get_drvdata(dev);
> + struct ssp_device *ssp = drv_data->ssp;
> + u32 status;
> + irqreturn_t ret;
> +
> + status = pxa_ssp_read_reg(ssp, SSSR);
> + ret = IRQ_NONE;
> +
> + if (status & sssr) {
> + dev_warn(dev, "spurious interrupt: 0x%02x\n", status);
> + pxa_ssp_write_reg(ssp, SSSR, (status & sssr));
> + ret = IRQ_HANDLED;
> + }
> +
> + if (status & SSSR_RFS) {
> + while (status & SSSR_RNE) {
> + u32 data;
> +
> + data = pxa_ssp_read_reg(ssp, SSDR);
> + drv_data->data[drv_data->index + 0] = (data >> 8);
> + drv_data->data[drv_data->index + 1] = data;
> + drv_data->index += 2;
> + if (HEADER_LENGTH(drv_data->data[0]) < drv_data->index)
> + navpoint_packet(dev);
> + status = pxa_ssp_read_reg(ssp, SSSR);
> + }
> + ret = IRQ_HANDLED;
> + }
> +
> + return ret;
> +}
> +
> +static int navpoint_suspend(struct device *dev)
> +{
> + struct driver_data *drv_data = dev_get_drvdata(dev);
> + struct ssp_device *ssp = drv_data->ssp;
> +
> + gpio_set_value(drv_data->gpio, 0);
> +
> + pxa_ssp_write_reg(ssp, SSCR0, 0);
> +
> + clk_disable(ssp->clk);
> +
> + return 0;
> +}
> +
> +static int navpoint_resume(struct device *dev)
> +{
> + struct driver_data *drv_data = dev_get_drvdata(dev);
> + struct ssp_device *ssp = drv_data->ssp;
> + int timeout;
> +
> + clk_enable(ssp->clk);
> +
> + pxa_ssp_write_reg(ssp, SSCR1, sscr1);
> + pxa_ssp_write_reg(ssp, SSSR, sssr);
> + pxa_ssp_write_reg(ssp, SSTO, 0);
> + pxa_ssp_write_reg(ssp, SSCR0, sscr0); /* SSCR0_SSE written last */
> +
> + /* Wait until SSP port is ready for slave clock operations */
> + for (timeout = 100; timeout != 0; --timeout) {
> + if (!(pxa_ssp_read_reg(ssp, SSSR) & SSSR_CSS))
> + break;
> + msleep(1);
> + }
> + if (timeout == 0)
> + dev_err(dev, "timeout waiting for SSSR[CSS] to clear\n");
> +
> + gpio_set_value(drv_data->gpio, 1);
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_SUSPEND
> +static const struct dev_pm_ops navpoint_pm_ops = {
> + .suspend = navpoint_suspend,
> + .resume = navpoint_resume,
> +};
> +#endif
> +
> +static int __devinit navpoint_probe(struct platform_device *pdev)
> +{
> + struct navpoint_platform_data *pdata = pdev->dev.platform_data;
> + int ret;
> + struct driver_data *drv_data;
> + struct ssp_device *ssp;
> + struct input_dev *input;
> +
> + drv_data = kzalloc(sizeof(*drv_data), GFP_KERNEL);
> + if (!drv_data) {
> + ret = -ENOMEM;
> + goto ret0;
> + }
> +
> + ssp = pxa_ssp_request(pdata->port, pdev->name);
> + if (!ssp) {
> + ret = -ENODEV;
> + goto ret1;
> + }
> +
> + /* HaRET does not disable devices before jumping into Linux */
> + if (pxa_ssp_read_reg(ssp, SSCR0) & SSCR0_SSE) {
> + gpio_set_value(pdata->gpio, 0);
> + pxa_ssp_write_reg(ssp, SSCR0, 0);
> + dev_warn(&pdev->dev, "ssp%d already enabled\n", pdata->port);
> + }
> +
> + input = input_allocate_device();
> + if (!input) {
> + ret = -ENOMEM;
> + goto ret2;
> + }
> + input->name = pdev->name;
> + __set_bit(EV_KEY, input->evbit);
> + __set_bit(KEY_ENTER, input->keybit);
> + __set_bit(KEY_UP, input->keybit);
> + __set_bit(KEY_LEFT, input->keybit);
> + __set_bit(KEY_RIGHT, input->keybit);
> + __set_bit(KEY_DOWN, input->keybit);
> + input->dev.parent = &pdev->dev;
> + ret = input_register_device(input);
> + if (ret) {
> + input_free_device(input);
> + goto ret2;
> + }
> +
> + drv_data->ssp = ssp;
> + drv_data->gpio = pdata->gpio;
> + drv_data->input = input;
> +
> + platform_set_drvdata(pdev, drv_data);
> +
> + ret = request_irq(ssp->irq, navpoint_int, 0, pdev->name, &pdev->dev);
Could this be a threadded irq?
> + if (ret)
> + goto ret3;
> +
> + navpoint_resume(&pdev->dev);
Could this be pushed to open instead?
> +
> + dev_info(&pdev->dev, "ssp%d, irq %d\n", pdata->port, ssp->irq);
> +
> + return 0;
> +
> +ret3:
> + input_unregister_device(input);
> +ret2:
> + pxa_ssp_free(ssp);
> +ret1:
> + kfree(drv_data);
> +ret0:
> + return ret;
> +}
> +
> +static int __devexit navpoint_remove(struct platform_device *pdev)
> +{
> + struct driver_data *drv_data = platform_get_drvdata(pdev);
> + struct ssp_device *ssp = drv_data->ssp;
> + struct input_dev *input = drv_data->input;
> +
> + navpoint_suspend(&pdev->dev);
> +
> + free_irq(ssp->irq, drv_data);
> +
> + input_unregister_device(input);
> +
> + pxa_ssp_free(ssp);
> +
> + kfree(drv_data);
> +
> + return 0;
> +}
> +
> +static struct platform_driver navpoint_driver = {
> + .probe = navpoint_probe,
> + .remove = __devexit_p(navpoint_remove),
> + .driver = {
> + .name = "navpoint",
> + .owner = THIS_MODULE,
> +#ifdef CONFIG_SUSPEND
> + .pm = &navpoint_pm_ops,
> +#endif
> + },
> +};
> +
> +static int __init navpoint_init(void)
> +{
> + return platform_driver_register(&navpoint_driver);
> +}
> +
> +static void __exit navpoint_exit(void)
> +{
> + platform_driver_unregister(&navpoint_driver);
> +}
> +
> +module_init(navpoint_init);
> +module_exit(navpoint_exit);
> +
> +MODULE_AUTHOR("Paul Parsons <lost.distance at yahoo.com>");
> +MODULE_DESCRIPTION("Synaptics NavPoint (PXA27x SSP/SPI) driver");
> +MODULE_LICENSE("GPL");
> diff -uprN clean-3.2-rc7/include/linux/input/navpoint.h linux-3.2-rc7/include/linux/input/navpoint.h
> --- clean-3.2-rc7/include/linux/input/navpoint.h 1970-01-01 01:00:00.000000000 +0100
> +++ linux-3.2-rc7/include/linux/input/navpoint.h 2011-12-31 11:54:02.859594707 +0000
> @@ -0,0 +1,12 @@
> +/*
> + * Copyright (C) 2011 Paul Parsons <lost.distance at yahoo.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +struct navpoint_platform_data {
> + int port; /* PXA SSP port for pxa_ssp_request() */
> + int gpio; /* GPIO for power on/off */
> +};
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-input" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
More information about the linux-arm-kernel
mailing list